... Mounting Kit. Cast aluminium clamp used to attach 25-50 mm diameter antenna mast or boom to 50 or 75 mm diameter mounting pipe. U-Bolts to attach to mounting pipe to be ordered separately (two required). ...
Clamping force: 20 kN - 100 kN
... sliding model using the press T-slot - variable clamping stroke (up to 8 - 12 mm depending on the model) - can be used on both the bolster and the ram - it can be fixed to provide fully automated clamping ...
SERAPID
... Multiple clamping for fewer tool changes and longer spindle running times on 5-axis machines. Best accessibility for short tools. Our 5-axis pyramids enable precise and efficient multiple clamping ...
... Bolt the clamp down to your worktable using the 3/8″ hole in the base. The 1/2″ copper plated Acme spindle resists weld spatter, and the swivel tip makes quick contact with your workpiece. Copper Plated Acme Screw / Ductile Iron Body Hold ...
Strong Hand Tools
... reacts and makes a clamping cylinder in the clamp push against it. By this the contacting is established. A black push button is installed on the clamp to disconnect the contacting. It is no problem ...
Clamping force: 0 kN - 150 kN
... • side operation • low profile • with through-hole thread ...
JAKOB Antriebstechnik GmbH
Clamping force: 15,000 N
... Product details Clamping force of up to 15,000 N Nearly unbreakable and tempered Tried-and-true BESSEY all-steel quality ...
BESSEY Tool GmbH & Co. KG
... For faster cycles and higher clamping force. The SHG / SH pneumatic clamping device impresses with its high clamping force and fast cycles, ideal for precise and efficient clamping ...
... For use in the printing cylinder of sheet-fed printing presses. Clamp ring made of higher strength steel sheet ensures a secure fit on the shaft. Punched part with a tolerance measurement on the front faces and spring support attached ...
... Application : Suitable for Food and Beverage, Pharmaceutical, Personal care, Pet Products, Dairy, Chemical, Breweries, Wineries & Distilleries Can be installed anywhere a traditional tri-clamp is used Features: Consistent, controlled compression of ...
... The Girder Clamp is a critical fastener designed to securely hold onto structural members, such as crane frames or girders. This clamp provides a sturdy and reliable attachment point for lifting and moving heavy loads. The ...
... ensures two- sided acting lift and allows you to open and close the clamp quickly. Through the mounting holes the clamp kann mounted on a T-Slotplate or a thread grid plate. Pneumatik clamp PS-150-AL chuck ...
Stritzelberger GmbH
Clamping force: 56 tf - 224 tf
... swing clamp arm allows the EAS double acting swing clamp to clamp vertically after swinging 90 degrees. To allow unobstructed loading and unloading of dies or parts, this product is mounted beneath the ...
Clamping force: 40 kN - 90 kN
... pressure die casting ■protected Trademark Multi Quick ■stepless vertically and horizontally adjustable ■strong clamping pressure for small clamping torque ...
Lenzkes Spanntechnik GmbH
... treated: HRC 32°~38° Surface finish: Black Oxide. Features: The cylindrical pin minimizes contact area and is useful for clamping in horizontal holes & round profiles. ...
Leave Industrial
... Speed and synchronization are easily adjusted when equipped with direct mount speed controllers. Air venting is QUICK with speed controller or air vent valve. Speed controller and air valve are for use with manifold (C type) hydraulic supply. ...
KOSMEK
Clamping force: 14,100, 14,250 N
... - Made of anodized aluminium - Swinging clamp to allow an easier up/down-loading of the slabs - Air fittings diameter can be chosen from the most common options - Quick up/down-loading - Quick air fittings - Stainless steel screws - ...
GNC Meccanica
Clamping force: 1.5 kN - 13 kN
... compensation system, these swing clamp cylinders maintain the clamping point with maximum precision over a long operating time. They can be equipped with clamp arm position control valves to ensure precise workpiece clamping. ...
HYDROBLOCK
... hydraulic sliding clamps are integrated with a maximum clamping force of 80 kN, and are specially designed for minimizing down time when setting up or when it need to be frequently replaced. They are characterized by ...
... B TYPE (ALUMINUM ALLOY BODY) Product Description Model No. LD-30B / LD-40B / LD-50B Vertical and horizontal configuration. Applicable to BT, CAT, DIN tapers. ...
Clamping force: 400 N - 5,000 N
... Pneumatic Clamping Element For rails : 15 to 65 mm Type: Closed without pressure Body in steel Operating temp. -20°C to 80°C Operation Pressure 5,5 to 8 bar ...
FLI - France Linéaire Industrie
... Complex clamping devices Custom made machine tool clamping devices for workpiece positioning - hydraulic or pneumatic. • Hydraulic clamping device ...
... We have shown rapid growth in the market and we provide our customers premium quality of Brass Component. We make the components with accuracy of as low as 10 microns. High Quality Customized Turned Parts with great precision & Accuracy can be made very ...
... We have metal clamps in multiple sizes to hold bellows, sleeves, hose … ...
... Transfer Deck This unique piece is a brilliantly simple way to transfer material efficiently. There are no chains, gears, or motors, which makes operation simple with little maintenance. ...
the best suppliers