Voltage: 207 V - 253 V
Current: 2 A
Power: 2 W
... Application: Isolating switch amplifier with intrinsically safe control circuit class [Ex ia] IIC for inductive contacts according to DIN 19234 or NAMUR or mechanical contacts in hazardous industrial plants. Case:NORYL SE 0 (self ...
Manfred Jünemann Mess- und Regeltechnik GmbH
Voltage: 80 V
Current: 5 A
... The PA09 is a 5A, 80V power operational amplifier designed to drive a variety of loads from DC through the video frequency range. Excellent input accuracy is achieved with a dual monolithic FET input transistor which ...
Apex Precision Product
Voltage: 0.78 V - 1 V
Power: 1,800 W - 5,500 W
Frequency: 20 Hz - 20,000 Hz
Guangzhou Proaudio Industrial Co., Ltd.
... Features Offset/gain controls Self contained globally compatible power supply Integral summing amplifier for thickness output Three outputs 0-10 V dc output jacks 2 CH + Thickness Bar graph display, Optional digital ...
MTI Instruments
Voltage: 100 mV - 15,000 mV
Frequency: 10 Hz - 100,000 Hz
... component characterisation, bridge networks and to measure the resistance of superconductors. The output from a lock-in amplifier is a DC voltage proportional to the amplitude of the input signal but with the noise ...
Scitec Instruments
Voltage: 5 V
Current: 5 mA
Frequency: 100 kHz - 10,000 kHz
... without adding more clocks Output capabilities include AC and DC coupled modes. In AC-coupled mode, the unit can receive and distribute timebase and reference frequency signals up to 10 MHz. In DC-coupled mode, Model ...
Power: 5 W
Frequency: 750 MHz - 4,000 MHz
... Up to 3.5GHz, 4W,2х2mm ● Built with leading edge RF IC design technology ● Passive RF IC，no need external DC power supply ● Wide Freq range 750-4000MHz ● Small Size:2.0 x 2.0 mm ● Very Low Loss & Low VSWR ● Excellent directivity ● ...
Yantel Corporation
Voltage: 0 kV - 50 kV
Current: 0 mA - 12 mA
... Specifications Output Voltage Range: 0 to ±50 kV DC or peak AC Output Current Range: 0 to ±12 mA DC or peak AC Slew Rate: Greater than 350 V/μs Large Signal Bandwidth: DC to greater than 1.4 kHz (2% ...
TREK, INC.
Current: 50 A
... The CGS-MV_I card is a precision DC measurement amplifier module (limited AC measurement). It is designed to measure, depending on the shunt resistor, up to 50 A continuously. The typical accuracy is 0.05 % with resolutions ...
Voltage: 15 V - 18 V
Current: 800 mA
The MOBALine-Booster is a device for the amplification of MOBALine signals. Extensions of more than 1000 meters and with approximately 70 additional clocks are achievable. Existing installations can easily be extended without the need for an additional ...
The Impulse Booster is a device for the amplification of impulse signals or line voltage transforming. Clock line extensions of more than 1000 meters and with approximately 100 additional clocks are achievable. Existing installation can easily be extended ...
Voltage: 24 V
Current: 1 A
... Amplifier series 400 for flow sensors Indication of the flow rate via LED strip Switching or analogue output To activate and deactivate fans and warning devices To signal flow failures For trend detection ...
Voltage: 24 V - 230 V
... ATEX amplifier series 400 for Ex flow sensors ST.../STS... Designs for AC or DC supply voltage Rail mounting in the control cabinet Visualisation of the flow rate via LED strip To activate and ...
Voltage: 30 V - 253 V
... in a switch cabinet in a non-explosive area Intuitive operation by means of potentiometer and LED display Power supply AC / DC variants ...
Voltage: 0 V - 10 V
Current: 4 mA - 20 mA
... The high-precision industrial DC- amplifier of the model series TesT 854 provides load-proportional signals. On the basis of a power supply of 24V or 230V an initially stable voltage will be generated, in order to feed ...
Voltage: 0.5 mV - 10 mV
Current: 30 mA
Frequency: 1,000, 10,000, 25,000 Hz
... FUTEK's IAA100 Analog Load Cell Amplifier with Voltage Output is FUTEK’s brand new general purpose amplifier solution for in-line amplification of any full bridge strain gauge type sensor with mV/V range output. The new ...
Voltage: 5 V - 10 V
Current: 0 mA - 20 mA
Frequency: 1 Hz - 5,000 Hz
... powered from 110/230 VAC or 18-24 VDC (selected at time of order). An optional isolated power supply module can extend the DC power input range from 9 to 36 V. Housed in a black surface mounted ABS case, it offers IP65 ...
Voltage: 0 V - 250 V
Current: 5 A
Power: 8, 6 W
... Small signal amplifier that enables 2 programmable alarms to the values desired in each case. Each alarm level has an output for a voltage-free contact normally open (when unit is powered ) that withstands maximum 250V and 5A. It admits ...
Voltage: 18 V - 30 V
Current: 2 mA - 10 mA
Frequency: 0 Hz - 20,000 Hz
... Side exit, high temp 260°C, high frequency 20 mV/g sensor & charge amplifier system w/ 16' J3 integral cable, case isolated, ATEX certified for use in Zone 0 and Zone 1 hazardous areas • Industrial ruggedness • ATEX certified Zone ...
Voltage: 24 V
Current: 4 mA - 20 mA
... gauge Ability to increase the signal of the 50 mV/V Semiconductor stress Gauge Input voltage: 24 AC/ DC Output voltage: 0 to 10 DC Zero compensation: +/-50% of FS Temperature range : -10 to 50°C ...
Voltage: 400 V
Current: 40, 13, 26, 52 A
Frequency: 20 kHz
... • Mobile power amplifier • AC/ DC 4-quadrant amplifier • DC to 20 kHz • Output current max. 52 A ±100 V • Extensive service functions • Intergrated in 19? mobile cabinet Applications Specially ...
Voltage: 24 V
Current: 1 A
Power: 30 W
... power amplifier for electro-hydraulic proportional control valve Control signal input voltage: 0 ~ +10 V ...
Voltage: 24 V - 230 V
... mounting rail/DIN rail 35 × 7.5 mm Voltage supply - AC/ DC 24 to 230 V Configuration - Via DIP switch Input - 0(4) to 20 mA, supply isolation amplifier operation or input isolating amplifier operation ...
Voltage: 180 V
Frequency: 40 Hz - 100,000 Hz
... For all vibration exciters that require a 180 VA power amplifier (load impedance 0.8 Ω). The PA 180 DM offers a max. frequency range DC ... 100 kHz, small harmonic distortion, excellent stability even with temperature ...
SPEKTRA Schwingungstechnik und Akustik GmbH Dresden
Voltage: 240, 120, 220, 110, 115 V
Current: 50, 100 A
Frequency: 100 kHz
... Guildline Instruments 7810 Wideband Transconductance Amplifier is the latest innovation for High Current, Wide Bandwidth AC Outputs. The 7810 opérâtes from DC to 100 kHz with very low distortion. By connecting the output ...
Voltage: 12 V - 24 V
Current: 60 mA
... Lanbao fiber amplifier and optical fibers; Built-in high-speed digital processing chip; Rich functions, easy to set up, and widely used in various applications; NPN and PNP, depends on different part numbers; 12- 24VDC; 4-digit LED digital ...
Voltage: 24 V
Current: 4 mA - 20 mA
... capability to amplify either strain gage signal 2mV/V or semiconductor gage signal 50 mV/V. •Input voltage: 24 AC/ DC •Output voltage: 0 to 10 DC (4 – 20 mA as an option) •Zero compensation: +/-50% of FS •Temperature ...
Voltage: 0 V - 10 V
Current: 0 mA - 20 mA
Frequency: 1 kHz - 5 kHz
... powered from AC or DC supplies providing excitation for up to four x 350 Ohm strain gauge bridges. The conditioned output signal can be selected from 0-20 mA, 4-20 mA, 0-10 V, 0-5 V, ±5 V or ±10 V. Options include: Isolated DC ...
the best suppliers