- Robotics - Automation - Industrial IT >
- Automation >
- Modbus RTU input module
Modbus RTU input modules
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
... 16 digital input channels - Digital input for dry contact or wet contact - Input Voltage level: 10~50V - Over voltage protection: 70 Vdc - 2,500 Vdc optical isolation The ...
... operating temperature range - LED display allows to monitor the status address settings - Higher noise immunity: 1 kV surge protection on power inputs, 3 kV EFT, and 8 kV ESD protection - ...
... 124H: 32 channels digital input, sink or source, 34Pin male connector, 24Vdc, counting function supported (counting frequency up to 200Hz) ◆ the module supports 32 channels digital input, ...
ODOT Automation
... required) ◆ the internal bus of the module and field input adopts magnetic insulation. ◆ the module input channel is to be connected to the field active analog ...
ODOT Automation
CT-1218: 8 channels digital input/24VDC/PNP ◆the module supports 8 channels digital input, supports sink input,and the input voltage is 24VDC and ...
ODOT Automation
... protocol MODBUS RTU through the RS485 serial interface. A 16 bit counter is available on each input, the maximum frequency input is 100 Hz and it is possible to set one ...
SENECA | Automation Interfaces
Z-10-D-IN is a module with 10 digital inputs, 16 Vdc self-powered common negative and removable terminals section 2.5 mm. Unlike Rev. Hw1, this module includes 10 inputs ...
SENECA | Automation Interfaces
... communicate by the protocols CANopen or ModBUS RTU (protocol selectable through dip-switch). It disposes of 32 bit counters (N.8), maximum frequency input is 10 KHz. A 3-way galvanic ...
SENECA | Automation Interfaces
... disabled the corresponding solid-state relay (photo-MOS) repeats the input line open or closed status as configured. D6231E has eight inputs and eight independent outputs. Modbus ...
The module MU110-24.1TD is a 1-channel input module for resistor bridges (strain gauge). The module enables the direct connection of a resistor measurement bridge. The ...
akYtec GmbH
... In addition, the inputs can be used as digital inputs. The available voltage value at the outputs is 10...36 V DC. The module requires 24 V DC power supply and supports Modbus ...
akYtec GmbH
The analog input module MV110-24.8AS has 8 analog inputs (0-10 V, 0-5 mA, 0(4)-20 mA). The module requires 24 V DC power supply and supports Modbus ...
akYtec GmbH
The PCH Input Box adds six DC process inputs and one Loop power input for external sensors to PCH Engineering’s advanced PCH 1420 vibration monitor. PCH Input Box ...
The SM1 - 2 channels module of analogue inputs is destined to convert standard signals, resistance or temperature signals into numerical data accessible through the RS-485 or RS-232 port by means of the ...
6 RTD inputs DESCRIPTION : These modules are used with HMI, PLC or SCADA via Modbus RTU protocol. IO Studio is its PC software for setting communication. Data Acquisition ...
BRAINCHILD ELECTRONIC CO., LTD
3-channel Digital Input with Open/Short Circuit Detection and 1-channel Relay Output Module Features Power Relay Output Dry Contact Digital Input Digital Input With ...
... , mV, V or mA input signals connected to the universal analog input. It is also capable acquire up to 3 digital inputs and to drive one solid-state relay and two SPST relays and is available ...
DATEXEL SRL
... MPNC030 product is an expansion module for analog inputs. The MPNC030 module has 4 independent and individually programmable analog inputs for acquisition of voltage, ...
... life power supply with protection for over temperature, short circuit, overcurrent/overvoltage The TELEPRO-HEIM-48Input Module is a flexible, functional and reliable solution for protection and ...
... returned to the host through the digital input, and the digital input has a counting function, which can be used as a pulse counter input. 1. 2 digital inputs(Dry ...
Current Input ±20mA, 4~20mA, 0~20mA Input Impedance Current: 120 Ω Sampling Rates 2.5 Samples/Second per Channel Communication Protocol: Modbus RTU Introduction W-M1B109 ...
ADVANIO TECHNOLOGY Co., Ltd.
... monitoring 24 digital input(can be used as pulse counter). It supports Modbus RTU Protocol over RS485 serial port. Powered up by 10~30VDC. The DAM142 is used widely in industrial automation ...
King Pigeon Hi-Tech Co., Ltd.
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining