- Robotics - Automation - Industrial IT >
- Automation >
- Serial input module
Serial input modules
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
... differential, two single-ended - Input type: mV, V, mA - Sampling rate: 10 samples/sec. (total) The ADAM-4017 is a 16-bit, 8-channel analog input module that provides programmable ...
ADVANTECH
... 16 digital input channels - Digital input for dry contact or wet contact - Input Voltage level: 10~50V - Over voltage protection: 70 Vdc - 2,500 Vdc optical isolation The ...
ADVANTECH
... operating temperature range - LED display allows to monitor the status address settings - Higher noise immunity: 1 kV surge protection on power inputs, 3 kV EFT, and 8 kV ESD protection - ...
ADVANTECH
... 124H: 32 channels digital input, sink or source, 34Pin male connector, 24Vdc, counting function supported (counting frequency up to 200Hz) ◆ the module supports 32 channels digital input, ...
... MODBUS RTU through the RS485 serial interface. A 16 bit counter is available on each input, the maximum frequency input is 100 Hz and it is possible to set one input ...
SENECA | Automation Interfaces
Z-10-D-IN is a module with 10 digital inputs, 16 Vdc self-powered common negative and removable terminals section 2.5 mm. Unlike Rev. Hw1, this module includes 10 inputs ...
SENECA | Automation Interfaces
... protocol selectable through dip-switch). It disposes of 32 bit counters (N.8), maximum frequency input is 10 KHz. A 3-way galvanic isolation among Power supply // input // RS485 circuits assures the integrity ...
SENECA | Automation Interfaces
The module MU110-24.1TD is a 1-channel input module for resistor bridges (strain gauge). The module enables the direct connection of a resistor measurement bridge. The ...
akYtec GmbH
... In addition, the inputs can be used as digital inputs. The available voltage value at the outputs is 10...36 V DC. The module requires 24 V DC power supply and supports Modbus RTU/ASCII ...
akYtec GmbH
The analog input module MV110-24.8AS has 8 analog inputs (0-10 V, 0-5 mA, 0(4)-20 mA). The module requires 24 V DC power supply and supports Modbus RTU/ASCII communication ...
akYtec GmbH
The SM1 - 2 channels module of analogue inputs is destined to convert standard signals, resistance or temperature signals into numerical data accessible through the RS-485 or RS-232 port by means of the ...
LUMEL
... sensors, mV, V or mA input signals connected to the universal analog input. It is also capable acquire up to 3 digital inputs and to drive one solid-state relay and two SPST relays and ...
DATEXEL SRL
... EN60947-5-6 NAMUR), NO or NC input and for NO or NC floating solid-state relay (photo-MOS) isolated output compatible with logic circuits. Configuration is programmable from PC by the GM Pocket Portable Adapter PPC5092 ...
supply voltage 24V= LED indicator for input 1 potentiometer power consumption 0,5W nominal input specification 24V= min. 5 mA protection class terminals IP20 housing IP50 screws pozidrive ...
... acquisition modules, which are also called distributed IO modules, IO modules, data acquisition cards, data loggers, and IO cards. FEATURES * Portable * Modbus connectivity ...
BRAINCHILD ELECTRONIC CO., LTD
... 24Vdc ( ±%20) Power Consumption - 1,5W Communication Port - 1x RS-485 Program Installation/Configuration - 1x USB (Mini USB2.0) Inputs - 2x or 4x (Pt-100, Pt-1000, PTC, NTC, 0…50mV) ADC Resolution ...
... channel Digital Output slave module of TPM EtherCAT® Add-on modules with NPN type. EZC-D102-XN can support local CAN bus through CAN Coupler, EZC-N100. With EtherCAT® control, it will lead to fast ethernet ...
... other modules and devices. For a similar module with two isolated channels, see SNAP-AIARMS-i. Part of the SNAP PAC System, the module mounts on a SNAP PAC rack with a SNAP PAC ...
Opto 22
... life power supply with protection for over temperature, short circuit, overcurrent/overvoltage The TELEPRO-HEIM-48Input Module is a flexible, functional and reliable solution for protection and ...
2DI Remote Digital Input Module(2 digital input,supports pulse counter and TTL) Model no:DAM102 The DAM102 remote data acquisition module is designed for harsh industrial ...
【W-M1B103】8 Channels Analog Input (3 Types) Module (High Common Mode Voltage Protection) High Common Mode Voltage Protection 3-in-1 Analog Intput Voltage / Current / Thermocouple Input ...
ADVANIO TECHNOLOGY Co., Ltd.
... monitoring 24 digital input(can be used as pulse counter). It supports Modbus RTU Protocol over RS485 serial port. Powered up by 10~30VDC. The DAM142 is used widely in industrial automation control ...
King Pigeon Hi-Tech Co., Ltd.
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining