Voltage: 24 V
Current: 4 mA - 20 mA
... features wide amplification range (gain from 20 to 5,000) and the capability to amplify either strain gage signal 2mV/V or semiconductor gage signal 50 mV/V. •Input voltage: 24 AC/DC •Output voltage: 0 to 10 DC (4 ...
Voltage: 12 V - 24 V
Current: 100, 50 mA
Frequency: 10 Hz - 55 Hz
... Control output The load voltage is below 24V DC, and the load current is below 100mA. NPN open set electric output type (nesidual voltage below 1V) When light in ON /when light out ON, switching mode Automatic on time opération funclon Delay OFF, ...
Voltage: 0 V - 10 V
Current: 4 mA - 20 mA
... designed to amplify a signal to equipment with current loop 4-20mA or 0-10V. For 35mm DIN rail. Features: Range of operation temperature Min:-10ºC / Max: +40ºC. Power supply: 24VDC. Range of input signal: 0 – 30 ...
Ascell Sensor,S.L.
Voltage: 110 V - 200 V
Frequency: 0 Hz - 20,000 Hz
... All DynaLabs vibration shakers come included with an amplifier out of the box. PM-20, PM-100, MS-20 and MS-100 shakers have integrated amplifiers. With this integrated amplifier it is very easy to ...
Voltage: 100 V - 1,200 V
Frequency: 2 Hz - 20,000 Hz
... Backgroundlit multifunctional display • Safety management system monitors temperature, overcurrent, clipping and overtravel • High Signal to noise ratio of >90 dB • Low distortion factor <0.1% • Selectable operation voltage range ...
Voltage: 30 V
... Waveform Amplifier 30 volts pk-pk • Extends the output range of function generators • 30 Volts peak to peak output swing • DC to 1MHz bandwidth • High impedance input, 0dB to +20dB gain • 50 Ohm and 600 Ohm ...
Voltage: 20 V - 253 V
Current: 1 mA
Power: 1 W
... amplifier filling level, Conductive, 23x114x99mm, 2 Channels,Clamp, IP20, Polyamide, With LED display Description Filling level sensors - Switching amplifiers Filling level and level sensors operate according to ...
Voltage: 250 V
Current: 1 A
... Galvanic Isolation Simple USB Configuration Port The SEM1630 is a DIN rail mounted trip amplifier which accepts RTD, Thermocouple, mV and passive current signals and provides a dual trip output. Isolation is provided ...
... total energy output, meeting the requirements of dual energy range experimental setups, avoiding the split of the signal on two shaping amplifiers. ...
Power: 6 W
Frequency: 2 MHz
... Laser light with variable wavelengths are available via optical parametric amplifiers. The AVUS Optical Parametric Amplifier (OPA) provides widely tunable high-energy pulses. It is ideal for use with 1 μm femtosecond ...
Power: 60 W
... ERBIUM-DOPED FIBER AMPLIFIER (EDFA) Neptec’s Erbium-doped fiber amplifier (EDFA) modules are designed for optical network signal amplification and long term reliability. Neptec’s EFDA and Polarization ...
neptec optical solutions
Voltage: 0 V - 10 V
Current: 0 mA - 1 mA
... millivolt-level transducer output signals to a 0-to-10 Volt DC signal proportional to tension and a 0-to-1mA signal proportional to tension. Using an iAMP2™ module is a simple alternative to mounting ...
... features TDP is a digital measuring amplifier for strain gauges bridge, including a 24 bit acquisition circuit with programmable gain .Through the Profinet I/O interface it is possible to program all operational parameters of the unit: ...
Celmi
Voltage: 5 mV
Current: 59 mA
... Portable strain gauge amplifier and display About the TR150 Strain Gauge Amplifiers The TR150 is a completely portable, precision instrument packaged in a small, robust IP65 (NEMA 4) enclosure, weighing only 260 grams. ...
Althen sensors
Frequency: 90 Hz - 520 Hz
... The isolation amplifier Transcont TVA-120-U0 is used for galvanic isolation or for conversion of a signal into another signal. The integrated sensor supply allows the direct connection and by this the ...
ACS Control-System GmbH
Voltage: 50, 2 mV
Current: 4 mA - 20 mA
... features wide amplification range (gain from 20 to 5,000) and the capability to amplify either strain gage signal 2mV/V or semiconductor gage signal 50 mV/V. ...
the best suppliers