Wheel type rollers

Outer diameter: 13 mm - 35 mm
Force: 49 N - 196 N
Inside diameter: 4 µm - 8 µm

・Roller pin for should be prepared by the customer. ・Do not use in applications where impact load or thrust load is applied. ・“Allowable Load” mentioned above means allowable radial load based on the test of rotating ...

Outer diameter: 22 mm
Inside diameter: 6 mm

・Roller pin for should be prepared by the customer. ・Do not use in applications where impact load or thrust load is applied. ・“Allowable Load” mentioned above means allowable radial load based on the test of rotating ...

Outer diameter: 30 mm - 70 mm
Force: 2,260 N - 7,650 N
Inside diameter: 6 mm - 15 mm

Roller pin for should be prepared by the customer. The results below are based on a test run under the non-stress conditions.

Yoke type track rollers can be single- or double-row units and are fitted on studs. They consist of a needle roller and cage assemblies as well as thick-walled ...

Schaeffler stud type track rollers are available in a variety of designs both with and without an eccentric. They can handle high radial loads as well as axial loads resulting from alignment issues and ...

Inside diameter: 5 mm - 40 mm

... rings of the track rollers. In instances where there is a misalignment in relation to the raceway, designs with a crowned outside surface are used. Edge stresses must be avoided in these cases. Designed ...

Inside diameter: 0.5 in - 2.43 in

Browning® VER Style Ball Bearings Browning® VER bearings feature black oxide treated inner and outer rings, and extended inner race bearing with ball riding nylon retainer. Shaft lock is achieved by 120° spaced diamond faceted ...

Force: 0 N - 400,000 N

... load capacity of full complement cylindrical roller bearing / twin-roller The guide rollers are mounted into a sliding cassette which can be optimally positioned during final installation. ...

Outer diameter: 55 mm - 115 mm
Force: 11.9 kN - 190 kN
Inside diameter: 21 mm - 42 mm

... sandblasted or ground surface treatment. Guide rollers are executed in ball, needle or tapered roller bearing designs to offer a wide range of load capacities at various price levels. ...

Outer diameter: 55 mm - 115 mm
Force: 11.9 kN - 190 kN
Inside diameter: 15 mm - 35 mm

... sandblasted or ground surface treatment. Guide rollers are executed in ball, needle or tapered roller bearing designs to offer a wide range of load capacities at various price levels. ...

Outer diameter: 55 mm - 115 mm
Force: 3 kN - 190 kN
Inside diameter: 21 mm - 42 mm

... hardened race surfaces that can be supplied both with sandblasted or ground surface treatment. Guide rollers are executed in ball, needle or tapered roller bearing designs to offer a ...

Outer diameter: 26 mm - 290 mm

... operating environment, and cycle counts. The Heavy- Duty Idler Rollers and Rails' engineering expertise and manufacturing skills are what set the Load Runners® brand apart. The Heavy-Duty Idler Rollers ...

Outer diameter: 30 mm - 75 mm
Force: 200 N - 1,250 N
Inside diameter: 5 mm - 25 mm

The FTH series is a range of guide rollers from Blickle that can accommodate 15-100 kg loads. The models in the series are offered in various diameters ranging from 30 up to 75 mm. These rollers are forged ...

Outer diameter: 40 mm - 125 mm
Force: 450 N - 3,300 N
Inside diameter: 10 mm - 25 mm

... series by Blickle Räder+Rollen GmbH u. Co is a Guide roller which is made of high-quality materials. For this specific unit, it is reaction injected with polyurethane elastomer. This is the ideal guide roller ...

Outer diameter: 60 mm - 125 mm
Force: 20 N - 25 N
Inside diameter: 15 mm - 25 mm

... by Blickle, is a guide roller equipped with a thermoplastic polyureth tyre and running tread. It has an operating temperature that ranges from -25° C up to +70° C, weight of 150 kg, and dimensions of 80 x 20 mm. ...

Outer diameter: 80 mm - 85 mm
Force: 320 kN - 1,000 kN

Excellent for use on electric pallet trucks, also in case of heavy loads and high speed handling (up to 16 km/h). Their excellent values of rolling resistance make the manual handling of heavy loads easier.

Outer diameter: 80 mm - 85 mm
Force: 320 N - 1,000 N

Excellent for use on electric pallet trucks, also in case of heavy loads and high speed handling (up to 16 km/h). Their excellent values of rolling resistance make the manual handling of heavy loads easier.The model with electrowelded ...

Outer diameter: 40 mm - 82 mm
Force: 700 daN - 1,200 daN

Suitable for use on manual pallet trucks, also with humidity and highly aggressive chemical agents. Their excellent values of rolling resistance make the manual handling of heavy loads easier. It is specifically recommended for use in ...

Outer diameter: 0.771 in - 1.803 in

MadeWell® – Radial Wheels & Crown Rollers MadeWell represents simple solutions for complex problems. This product line takes us back to our roots of solving everyday challenges for industries such as ...

To guide moving parts in the slot of the aluminum profile, with ball bearing Material Nylon PA, glass ball reinforced Color Black Pack Quantity 10 pieces Specials conductive, other colors on request

Description To guide moving parts in the slot of the aluminum profile Material Roller: Nylon PA, glass ball reinforced Bush: Steel, zinc plated Washer: Steel, zinc plated Color Black Pack Quantity 10 pieces Specials conductive, ...

Description To guide moving parts in the slot of the aluminum profile Material Roller: Nylon PA, glass ball reinforced Bush: Steel, zinc plated Washer: Steel, zinc plated Color Black Pack Quantity 10 pieces Specials conductive, ...

Outer diameter: 48, 80 mm

Outer diameter: 26 mm - 200 mm
Force: 2.8 N - 159 N
Inside diameter: 10 mm - 64 mm

MPCR: Plain Stud Type MPCR Series bearings are designed to handle both axial and radial loads by using Tapered Roller Bearings or Deep Groove Ball Bearings. These bearings should be used when standard ...

Outer diameter: 26 mm - 200 mm
Force: 2.8 N - 159 N
Inside diameter: 10 mm - 64 mm

MFCR: Flanged Stud Type MFCR Series bearings are designed to handle both axial and radial loads by using Tapered Roller Bearings or Deep Groove Ball Bearings. These bearings should be used when standard ...

Outer diameter: 40 mm - 165 mm
Force: 2.8 N - 148.1 N
Inside diameter: 10 mm - 48 mm

MVCR: V-Groove Stud Type MVCR Series bearings are designed to handle both axial and radial loads by using Tapered Roller Bearings or Deep Groove Ball Bearings. These bearings should be used when standard ...

Outer diameter: 10, 60, 80, 120 mm

... version of TRAPOROL's all-side rollers can be mounted around the axles. The rollers are extremely robust and ensure smooth and trouble-free handling during conveying, turning and pushing. TRAPOROL’s polydirectional ...

... high precision LR series Track rollers with cylindrical or crowned outer ring are used in applications where friction has to be lowered as in case of heavy loads track or as idler wheel. ...

Outer diameter: 50 mm - 60 mm
Inside diameter: 12.7 mm

ROLLERS WITH NIB AND ORDER FORM MODELS RO 30 - RO 40 - RO 50 Characteristics: All rollers are realized in nylon with 1 or 2 nibs, using the injection moulding technique; assembly on mm 12 diameter ...

Outer diameter: 52.5 mm - 149 mm
Force: 10,000 N - 353,000 N
Inside diameter: 30 mm - 60 mm

Combined Rollers Centric combined bearings Functionality and properties: Combined bearings are made of high quality steel and have hardened treads. The welding bolts can be welded to mounting plates or directly onto ...

Roller bearing for inspection machines suitable for SGCC, EMHART, OI equipment we provide rollers fitted with ball bearings and covered with a PU (vulcolan) coating with 90 - 95 Shores A. Technical ...

Outer diameter: 1.5 in
Inside diameter: 0.88, 0.887 in

Solid rollers have a smooth surface and are permanently bonded to a steel insert. The steel insert provides rigidity and allows the user to customize the mounting configuration based on the application. Rollers ...

Outer diameter: 2, 2.5, 4 in
Inside diameter: 1.25 in

Finned rollers have grooves on the surface and are permanently bonded to a steel insert. The steel insert provides rigidity and allows the user to customize the mounting configuration based on the application. ...

Outer diameter: 1.5 in - 6 in
Inside diameter: 0.5 in - 0.505 in

Solid rollers have a smooth surface and are permanently bonded to a steel insert with the bearings held into place with snap rings. Rollers are available in neoprene, nitrile and urethane materials with ...

Outer diameter: 36 mm - 49.5 mm
Force: 0 daN - 840 daN

Rollers for TWIN-RAIL production lines Outer casing in polyacetal Nitrile rubber seals Outer and inner rings with heat and surface treatments to reinforce resistance to loads and corrosion. Balls in 100Cr6, cage in polyamide Special ...

Outer diameter: 40 mm
Force: 0 daN - 525 daN

... points on the tubular guide rail. Improved resistance to sudden shocks and shifts in direction. Axial clearance allows the rollers to continue functionning efficiently even in bends in the production lines.

Outer diameter: 36 mm - 49.5 mm
Force: 0 daN - 840 daN

ROLLERS WITH ANGULAR CONTACT FOR MONO-RAIL PRODUCTION LINES Geometric studies have been used to optimize load distribution. Angular contact ball bearings are filled with an optimized number of balls on both rows. The ...

Outer diameter: 68 mm - 197 mm
Inside diameter: 20 mm

Inside diameter: 25 mm - 40 mm

Outer diameter: 197 mm - 317 mm

Roller followers without = spherical -X = cylindrical IKO: -R spherical -ZZ with cover plate ZZUU with cover plate and sealing lip

Inside diameter: 3 mm - 90 mm