DOLD DIN rail monitoring relays
Tripping current: 5, 10 A
Trigger voltage: 115, 230 V
Fluid Level Monitoring Relay 230VAC Sensitivity Adjust On Delay and Off Delay Timer Filling & Emptying Functions Key Features • Compact 36mm Design • Filling and Emptying Functions • ...
Tripping current: 4, 6 A
Trigger voltage: 24, 250 V
... groups of signal output functional safety relays. Manual or automatic reset is supported, and diagnosis information can be determined by indicator changes. It has the function of short circuit monitoring ...
Bytorent Technology Co., Ltd.
Tripping current: 4, 6 A
Trigger voltage: 250, 240, 24 V
Supports emergency stop switch, safety door lock, PNP type safety light curtain, and photoelectric input Precise control, can be adapted to different safety functions through the function DIP switch. Dual-channel, single-channel-dual-channel, ...
Bytorent Technology Co., Ltd.
Tripping current: 6, 4 A
Trigger voltage: 240, 250, 24 V
Supports resistive, normally open, normally closed contact/carpet, 4-wire contact/carpet signal input Precise control, can be adapted to different safety functions through the function DIP switch. Dual-channel, single-channel-dual-channel, ...
Bytorent Technology Co., Ltd.
Tripping current: 5 A
Trigger voltage: 30, 230 V
The BMRCD-01 modular residual current device can be installed with MCCB and MCB in addition to shunt/under-voltage release for residual current protection. BMRCD-01 consists of a controlling module and detecting modules (only B-type detecting ...
Tripping current: 0.2 A - 10 A
Trigger voltage: 230 V
... 2 to 200 Hz). Monitoring is accomplished by recognizing the phase shift between current and voltage. This phase angle varies depending on the motor load. The functions can be adjusted by means of bridges S1 - S2 - S3S1 ...
METZ CONNECT
Tripping current: 4 A
Trigger voltage: 24, 230 V
The thermistor relay is used as protection relay for motors against thermal overload (inadmissible heating). This heating might be caused by mechanical overload on the shaft or when operating the motor ...
METZ CONNECT
Tripping current: 6 A
Trigger voltage: 24, 230 V
The level sensor monitors filling levels or leakage of all conductive, noncombustible media. The trigger can be adjusted by means of a proportional potentiometer. As monitor, the device works with an electrode (EO) and the ground connection ...
METZ CONNECT
Tripping current: 8 A
Trigger voltage: 250 V
... LEDs for diagnostics • Reset: configurable by dip-switch (SR=Automatic, N=manual) • Mounting: symmetrical DIN 35mm rail on DIN 50022 • Mounting: IP 20 electrical box ...
COMITRONIC - BTI
Tripping current: 8 A
Trigger voltage: 250 V
... diagnostics and 1 LED for power Reset: configurable by dip-switch (SR=Automatic, N=manual) Mounting: symmetrical DIN 35mm rail on DIN 50022 Mounting: IP 54 electrical box Electrical ...
COMITRONIC - BTI
Tripping current: 8 A
Trigger voltage: 250 V
... Indicators: 3 LEDs for diagnostics Reset: configurable by dip-switch (SR=Automatic, N=manual) Mounting: symmetrical DIN 35mm rail on DIN 50022 Mounting: IP 54 electrical box Electrical ...
COMITRONIC - BTI
Tripping current: 0.25 A - 10 A
... points independently adjustable • LED indicators for power supply, relay 1 (R1) and relay 2 (R2) Control relay for monitoring AC and DC voltage with two separately ...
HIQUEL
Trigger voltage: 80, 150, 350, 600 V
... True RMS measurement). -LCD display. – Measuring frequency range:45Hz-65Hz. – Voltage measurement accuracy<1%. – 2-MODULE,DIN rail mounting. • Control for connection of moving equipment(site equipment,agricultural ...
Zhejiang Geya Electrical Co., Ltd
Trigger voltage: 24, 42, 115, 230 V
The Klaschka Pulse Rate Measuring Relays can be applied as a standstill monitor of turning equipment, in a wide range of applications that involve machines and plants, vehicles and ships, mining industry, process engineering, ...
KLASCHKA Industrieelektronik
Trigger voltage: 24, 42, 115, 230 V
FSN Frequency and pulse rate measuring relays complete the ISN pulse rate measuring relay with high frequencies. Three threshold ranges from 100 Hz to| 120 kHz can be selected.
KLASCHKA Industrieelektronik
Tripping current: 1 mA - 15,000 mA
The undervoltage and overvoltage protection relay, manufactured by Klaschka, is a robust version relay that is incorporated with a self-supervision system and restriction settings. This is built to control ...
KLASCHKA Industrieelektronik
Tripping current: 10 A
Trigger voltage: 250 V
- Changeover contact - Contact material AgSnO2 Insulation Contact/contact 4 kV / 1 min Contact/coil 2 kV / 1 min Rated impulse withstand voltage open contact 1 kV / 1 min Pollution degree 3 Overvoltage category III General data Storage ...
Releco
Trigger voltage: 20 V - 240 V
... function Local Reset function Local Remote Output relays 2 changeovers (TRIP+SAFE, ALARM) 5 A (240 VAC) 0,3 A (110 VDC) 2 A (48 VDC) Display indications LED green(power ON) LED red TRIP (Relay ...
... Chordn’s three-phase monitoring relays HMPB7 series are mainly used to monitor the phase sequence, phase loss and over-undervoltage of power supply system. The width of these monitoring ...
... The 17.5mm pitch of our Chordn’s three-phase monitoring relays HMPA5C series are appropriate for monitoring the phase sequence-loss and undervoltage. Standard 35mm DIN ...
The 17.5mm pitch of our Chordn’s three-phase monitoring relays HMPA5A series are mainly designed for monitoring the phase sequence and phase loss. Standard 35mm DIN ...
Trigger voltage: 24 V
Multifuncton safety module with delayed outputs – Suitable for commanding interlocking devices with guards, associated with machinery with inertia, where the dangerous situation can last for a defined time after stop signal generation 2 ...
Comepi srl
Tripping current: 5 A
Voltage monitoring in 3-phase mains Meassuring circuit data Functions OVER, OVER+LATCH, UNDER, UNDER+LATCH, WIN, WIN+LATCH timing adjustment for tripping delay Time intervals (timing adjustment) tripping ...
RELPOL
Trigger voltage: 24 V
... 01-27 Article number 203009 Voltage supply 24 V AC / DC Input 1 x sensor 8.2 kOhm Output 1 x relay contact Housing Polyurethane, black for DIN rail 1.38 in Dimension ...
Trigger voltage: 208 V - 480 V
The SM 175, which is manufactured by GIC, is a voltage monitoring device that is suitable to use in controlling the sequence of three phases, and its supply voltage. The unit has a compact design, and has a modifiable ...
General Industrial Controls (P) Ltd.
The SM 501 is a supply monitoring device which is suitable for providing protection from phase reversal, phase-phase unbalance and phase loss. It is suitable for 3 phase and wire systems through the voltage sensing mechanism. ...
General Industrial Controls (P) Ltd.
Trigger voltage: 110 V - 240 V
The multi function timer has the ability to operate the work pieces within the power range of 24 up to 240 v. It is equipped with a wide selection of Earth Leakage Current of 60 mA up to 300 mA, and 02. A up to 1.2 A. ...
General Industrial Controls (P) Ltd.
... with two relay outputs, and you can program which of the parameters are active on each relay. The relays are activated at normal conditions, and releases if one or more of the selected ...
COMADAN
Trigger voltage: 5 V - 34 V
... SIL3/Cat 4) Programmable in function block language in accordance with IEC 61131-3 Programming, configuration, monitoring and debugging per SolutionCenter Manipulation protection thanks to configurable ...
Trigger voltage: 208 V - 600 V
Voltage monitoring realy for three-phase system, without neutral, phase loss and incorrect phase sequence, 208...480VAC 50/60Hz • ype of product: Voltage monitoring relays • Type ...
LOVATO ELECTRIC
... disappear, the relay turns off. It is available in two versions: • F 22. The relay turns ON only if the sequence is wrong. • F 33. The relay turns ON only if the sequence is right. The ...
... sequence of a threephase power line. The leds on the front point out: • Red led: relay ON. • Yellow led: supply voltage connected. If one or more phases disappear, the relay turns off. It is available ...
Trigger voltage: 24, 115, 230 V
... phase voltage relay A relay for monitoring AC voltage on the supply network, in accordance with application of sensitive supply voltage equipment or as an alarm relay ...
Brodersen Controls
Trigger voltage: 24, 115, 230, 400 V
... the hysteresis which is adjustable on the front, the relay de-energises. With inverted relay function the internal relay work the opposite way. The Voltage relay has ...
Brodersen Controls
Tripping current: 4 mA - 2,000 mA
Trigger voltage: 24, 115, 230 V
... current relay is a relay for monitoring off load in applications with a relative low AC- and DC current up to 2A AC/DC. The relay can with advantages be used as an alarm ...
Brodersen Controls
Tripping current: 0.2, 4 A
Trigger voltage: 195 V - 253 V
... corresponding red LED lighting up. In the normal operation the output relay is pulled on and the power light (green LED) lights up. In the fault case as well as at loss of the supply voltage the relay ...
Tripping current: 0.1, 0.3, 1, 4 A
Trigger voltage: 30 V - 460 V
... voltages above the switching point the output relay is pulled in with 2 change-over contacts and the operating light (green LED) shines. When one or several phase voltages sink below the switching point, the relay ...
Today KNX is the world standard, open and compliant with the main European and international regulations, for automatic and decentralised management of technological systems in a wide range of situations: commercial buildings, industry, ...
Tripping current: 4 A
The PQRM5100 31 … Three phase multifunction Power Transmitter suitable for the measuring of 51 different parameters of the three phase power network: • the TRMS values of phase voltages and phase currents • active power, reactive ...
Tripping current: 4 A
The PQRM5100 11 … Single-phase multifunction Power Transmitter suitable for the measuring of 12 different parameters of the singlephase power network: • The TRMS values of phase voltage and phase current • active power, reactive ...
Tripping current: 50 mA
Trigger voltage: 200 V
... following output options (2 limit-relays are standard, beyond that only one option at the same time): • +2 normally open relay contacts (SPST) for limit switching or for simple control tasks. (In this ...
Trigger voltage: 0 V - 480 V
The SLU-100 series consists of various universal motor relays that were designed to provide a cost-effective protection solution against premature failure for various equipment, as well as against downtime that may be ...
Over voltage & under voltage monitoing relay for demanding AC or DC applications Plug in relay Smitt style pinning 1CO + 1NO contact DC and AC coil Flash barrier 2 LED indicators Cadmium free contacts Adjustable ...
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining