- Electricity - Electronics >
- Electronic Component >
- Signal amplifier >
- Linear Technology
Linear Technology signal amplifiers
Voltage: 110 mV - 220 mV
Current: 4 mA - 6 mA
Power: 0 W - 130 W
IP Amplifier IPMG-130P This remote VolP amplifier units is IP-based power amplifier. The units is connected to the central exchange unit via ethernet Copper CAT5 or CAT6 or fibercable. ...
HONGKONG KOON TECHNOLOGY LTD
Voltage: 70 V - 100 V
Power: 480 W - 640 W
Frequency: 50 Hz - 60 Hz
... High-grade aluminum 2U black oxide brushed panel, beautiful and elegant; ※ 2-channel input, 10-zone output (70V/100V audio signal); ※ 10 channel partitions can be arbitrarily selected; ※ 25-pin computer activation ...
HONGKONG KOON TECHNOLOGY LTD
Voltage: 110 mV - 220 mV
Power: 70 W
Frequency: 50 Hz - 60 Hz
SIP Amplifier IPMG-70P This remote VolP amplifier units is IP-based power amplifier. The units is connected to the central exchange unit via ethernet Copper CAT5 or CAT6 or fibercable. ...
HONGKONG KOON TECHNOLOGY LTD
Voltage: 230 V
Sound and light amplifier for telephone, suitable for loud environments. Plus points Robust sounder: IP66 Power supply: 230 Vac Continuous operation Highly resistant, self-extinguishing ABS casing Telephone ...
ae&t
Voltage: 230 V
Sound and light amplifier for telephone, suitable for loud environments. Plus points Robust siren: IP66 Power supply: 230 Vac Continuous operation Highly resistant, self-extinguishing ABS casing Telephone plug ...
ae&t
Sound amplifier for telephone, suitable for loud environments. Plus points Robust siren: IP66 Power supply: Direct parallel connection to the telephone line Continuous operation Housing made of highly resistant, ...
ae&t
... dynamic system, and then converts the received digital signal into analog signal with output to the power amplifier unit. The digital signal, converted from the voltage/ ...
... unit in the power amplifier solutions for digital communication via AURORA protocol. Via the fiber digital port, it communicates with the real-time dynamic simulator system, and then converts the received digital signal ...
Voltage: 8 V - 32 V
... can be concentrated in the module and output CAN-Open signal. Technical Specifications - Power supply: 8-32V - Input signal: 6 path analog signals; 10 path switch signals - ...
II2(1)G Ex eb mb ib [ia Ga] IIC T4 Gb II2(1) D Ex tb ib [ia Da] IIIC T130°C Db Universal Ex switching amplifier for installation in Zone 1 / 2 / 21 / 22 Two configurable switching points / relay outputs Ambient temperature ...
Voltage: 0 V - 300 V
Current: 0 A - 10 A
... include a control system that receives data by means of analogue signals which the evaluated data is processed by a device such as a programmable logic controller (PLC). Transmitting analogue signals ...
... level indicator for visual control of output signal at BNC connector (OUT), which assures that the output signal is within the operating range of the amplifier. To dampen infrasonic ...
Voltage: 0 V - 10 V
... connectors), IP54 (with cable bushings) Operation and installation Nominal temperature range 10 … 40 °C Voltage output Zero signal adjustment range ±10 % Power supply Voltage VDC 24 VDC Additional properties Options Calibration ...
Current: 1, 2 A
Power: 20 W
Frequency: 100 kHz - 22,000 kHz
... RF power amplifier. The rated output power is 20W, P1dB output power is 40W. The gain is numerically adjustable, and the common settings can be saved with one click. It can be used with mainstream signal ...
Xi'an Aigtek Electronic Technology Co., Ltd.
Voltage: 35, 70 V
Current: 2 A
Power: 70 W
ATA-1372A is an ideal single-channel wide band amplifier that can amplify the AC and DC signals.matching with the mainstream signal generator, realize perfect signal ...
Xi'an Aigtek Electronic Technology Co., Ltd.
Voltage: 200, 100 V
Current: 500 mA
Power: 50 W
ATA-2021B is a single-channel high voltage amplifier capable of amplifying AC/DC signals. Maximum output 200Vp-p (±100Vp) high voltage, the DC offset voltage can be adjusted in three ranges, and the maximum ...
Xi'an Aigtek Electronic Technology Co., Ltd.
Voltage: 0 V - 5 V
A Range of 2 amplifiers dedicated to amplify the signals from PT100 and 1000 platinum probes. The APT amplifier is built in a very compact housing allowing an easy installation into any ...
TEXYS
Our AMPT 2L product is an in-line analogue strain gauge amplifier with offset and gain controlled by microcontroller. It makes work very simple as it allows for: - Gain and offset adjustment. - Initiation of a temperature ...
TEXYS
The XN5 strain gauge amplifier is a 4 channel output version of our popular XN4 strain gauge amplifier. With the XN5 strain gauge amplifier, it’s possible to use a single compact amplifier ...
TEXYS
Voltage: 70, 100, 50 V
Power: 120 W
Frequency: 10, 10 kHz
Power amplifier (Booster), Rated power output: 120W, Tones control: 1. Bass tones: ±10dB (100Hz) 2. Treble tones: ±10dB (10kHz). Frequency response: 30÷20,000Hz (-3dB), Sensitivity: 1250mV, Constant voltage outputs: 50-70-100V, ...
TELEA TECNOVISION SRL
Voltage: 50, 100, 70 V
Power: 480 W
Frequency: 100 Hz
... circuit, thermal switch located inside the power transformer, resettable thermal switch placed in contact with the power amplifier dissipator, mains fuses), fan cooling with automatic speed control.
TELEA TECNOVISION SRL
Voltage: 100 V
Power: 125 W
Frequency: 80 Hz - 200,000 Hz
Modular Audio Amplifier, 125W rated output power, Class D, EN 54-16 certified with diagnostic functions. Power outputs 100 V. Distortion at rated power < 1%. Frequency response 80-20.000 Hz, Low Cut filter (- 3 dB) ...
TELEA TECNOVISION SRL
Voltage: 24, 110, 220 V
Current: 25 mA
These units are very versatile as they can be used with all NAMUR, NPN and PNP sensors, functioning with relay ON or OFF load with a timing function in both states. Furthermore they have a programmable time scale from 0,03 seconds ...
Voltage: 12, 110, 220 V
Current: 50 mA
These instruments are made up of a transformer an amplifier and a transistor, a rectifying circuit and one or two output relays with changeover contacts, respectively in the ALNC and ALN2 types. They are used to supply ...
Voltage: 12, 110 V
Current: 25 mA
These instruments are made up of a transformer an amplifier and a transistor, a rectifying circuit and one or two output relays with changeover contacts, respectively in the ALNC and ALN2 types. They are used to supply ...
Power: 5 W
... offers quick and versatile set up. CV9-C: 9 channel charge amplifier with individually selectable gain (x1, x10, x100) per channel via a three way switch. CV9-CL: 9 channel charge amplifier with ...
Voltage: 10, 15 V
Current: 55, -20 mA
... supply line. Where the signal levels are adequate then minimal instrumentation is required to interface with the Accelerometer. The V4/04 Voltage Source Amplifier is a four channel space saving solution ...
Voltage: 24, 110, 230 V
Current: 6 A
Frequency: 60, 50 Hz
The VNR21.22 control units are designed as interface for conductive level probes SL series. These electronic units are used to control liquids that have a minimum electrical conductivity of 1 S. The system is based on measurement ...
Voltage: 24, 230 V
Current: 5 A
Frequency: 50, 60 Hz
The VNR2300 control unit was designed as low cost interface for conductive level probes. These electronic units are used to control liquids that have a minimum electrical conductivity of 10 S. The system is based on measurement of the ...
Voltage: 230, 24 V
Current: 5 A
Frequency: 50, 60 Hz
This control unit with double measuring channels was designed as low cost interface for conductive level probes and is used to control liquids that have a minimum electrical conductivity of 8 S. The system is based on measurement ...
Voltage: 18 V - 240 V
Power: 18 W
Frequency: 45 Hz - 65 Hz
The Fiberoptic Distribution Amplifier receives a single optical input and transmits from 2 to 8 identical optical outputs to deliver a cost-effective upgrade path. The TSC 4340A takes all timing signals-RF ...
Microsemi
Voltage: 24 V - 260 V
Current: 300 mA
OPTOCOUPLED STATIC OUTPUTS • 1 or 2 channels • General Features: These units allow to amplifiy signals from NAMUR sensors or contacts. Each output is electrically insulated from each other, from power supply and ...
BDC ELECTRONIC S.r.l.
Voltage: 24 V - 260 V
Current: 5 A
RELAY OUTPUT • 1 or 2 channels • General Features: These units allow to amplifiy signals from NAMUR sensors or contacts. The relay outputs have changeover N.O. + N.C. contacts electrically insulated from each other, from ...
BDC ELECTRONIC S.r.l.
Voltage: 24 V - 260 V
Current: 300 mA
... STATIC OUTPUT • 1 Timed channel General Features: These units allow to amplify signals from NAMUR sensors or contacts. The delay time and hold time respect the input signal are adjustable through ...
BDC ELECTRONIC S.r.l.
Voltage: 24, 110, 230 V
Current: 4 mA - 20 mA
Frequency: 50 Hz - 60 Hz
... -proof models Applications - Power supply and switching amplifier for 2-wire transmitters - Switching amplifier for 4-wire active transmitters - Dedicated switching amplifier ...
Voltage: 5 V - 15 V
Current: 0 mA - 20 mA
... Line Amplifier is an amplifier that is used to allow for longer cable runs and/or signal splitting to several GPS Repeaters. It has a gain of +16dB at the GPS L1,L2 and GLONASS frequency ...
Roger-GPS Oy
The UR series offers a wide array of remote photoelectric sensor amplifiers that function as control units for miniaturized sensors. Each unit is integrated with double timer complete with independent adjustment. It can ...
Power: 10 W
... without band switching or swapping narrow band amplifiers resulting in faster and more accurate testing. The amplifier can be used in wireless communications and component testing wherever a highly linear ...
Giga-tronics Incorporated
Current: 4 mA - 20 mA
... Load Cell Amplifier’s basic function is to amplify the signal from any load cell with full bridge connection. Amplifying this signal allows the user to use the data from the load cell ...
Datum Electronics
The ZET 410 preamplifier is used as a signal amplifier in processing systems and various instruments and actuator control systems. It is used in industry, laboratory and mobile studies. Both passive ...
ZETLAB
Voltage: 10 V
Current: 4 mA - 20 mA
... acquisition circuit, with a programmable gain. The digital amplifier is also utilized in 3 analog outputs, toward a supervision unit. The unit functions through allowing the analog signal to become ...
ASA-RT s.r.l.
Voltage: 12 V - 24 V
... this module also improves OSNR (Optical Signal to Noise Ratio). The MICROSENS Raman offers a maximum output power of 28.5 dBm. The amplifier includes an automatic eye safety mechanism that shuts down ...
MICROSENS GmbH & Co. KG
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining