TEC AUTOMATISMES DC electromechanical relays

Switching current: 10 A

... loads as normal or lock the relay to one load or the other. By locking the alternating relay to one load, the other load can be removed for service without rewiring the first load for continuous operation. Alternating ...

Switching current: 0.3 A - 1 A
Output voltage: 1.5 V - 24 V
Width: 5.7 mm

1.High sensitivity Rated operating power 100 mW (High sensitivity single side stable) 2.Compact size and slim Width (5.7 mm) x Length (10.6 mm) x Height (9 mm) 3.Compliant with Telcordia standard Surge withstand voltage 2,500 ...

Switching current: 16 A
Output voltage: 250 V

● switching capability ● 5kV dielectric strength (between coil and contacts) ● 2.0mm contact gap available ● Plastic sealed and flux proofed types available ● Sockets available ● UL insulation system:Class F

Switching current: 255, 205, 130, 90 mA

The CCR-49K/CR-49K is a broadband, multi-throw, electromechanical coaxial switch designed to switcha microwave signal from a common input to any of 3, 4, 5, or 6 outputs. The characteristic impedanceis 50 Ohms. The switches ...

Switching current: 25 A
Output voltage: 0 V - 440 V

... of power failure. The advantage of polarised latching relays is the pulse driven operation of some milliseconds, coil heating can be neglected. Relay can also be set by manual operation. The relays ...

The Class 47 alternator relay provides a means of automatically alternating the operation of two separately mounted motor driven pumps or compressors. This alternating action assures even readiness and wear on both pumps. ...

Switching current: 20 A - 63 A

... pole. Are you looking for savings in electric energy? Replace installation relays and contactors with latching relays. At remote switching of lighting, a parallel connection of pushbuttons is used. ...

Both electronic type and electromagnetic type relay available upon request; Min tripping power:100uVA; Magnetizing power:≥5000uVA; Resetting force: 1.2N-1.6N; Impedance when tripping power adjusted into 100uVA: 160 ...

... is a DC neutral line relay fitted with independent non-fusible contacts. It meets the requirements of relevant BRB Spec. Relay types covered under this category are: QN1 - Line ...

Output voltage: 250 V
Output current: 10 A

The JQC-3FF is a subminiature high-power relay commonly used in a variety of applications. It is a general-purpose, high-current relay that can switch loads up to 10A at 250V AC or 30V DC. ...

Switching current: 100 A

1.Single phase 100A switching capability; 2.Multi-layer blades, low temperature rise; 3.Low contact resistance < 1.0mΩ; 4.Environmental protection (comply with ROSH) ; 5.Outline dimension:43.2mm×33.2mm×22mm 6.Applied in Electronic ...

Switching current: 4.4 A - 87.8 A

... function minimum space design. Suitable for 50 Hz and 60 Hz frequency cycles. Available in 6, 12, 24, 110, 220 & 240V AC and DC. Built in Diode models with contact capacity of 10 Amperes. Features: • Compact housing ...

Switching current: 5 A

Series 37 Mounting Style: Plug-In Contact Form: 2C, 4C Rating: 5 A at 24VDC/230VAC Coil: 12-110 VDC, 110, 230 VAC

Switching current: 2.5 A - 30 A

High voltage relays for disconnecting and switching over of test paths and for the configuration of switch matrixes. These relays can be connected directly to a SCHLEICH test device via a 24 V DC ...

Switching current: 16 A

... deep. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. With the patented Eltako Duplex technology (DX) the normally potential-free contacts can ...

Switching current: 20 A

The 295 Series, manufactured by Deltrol Controls, is a power relay that is integrated with a rated current that ranges from 15 up to 50 amperes and a total temperature of 155°C. This is used in a wide range of applications ...

Start relay for starters – solenoid Completes the circuit that brings electric current from a vehicle's battery to the starter motor of the engine. Mounted in heavy duty vehicle engines. Designed and manufactured ...

- With cover, color can be changed according to customer needs - Relays with AC and DC coils have different colors of operating indicators (LEDs). - Printing on the coil tape indicates the operating ...

Switching current: 8 A - 16 A

... color for output status indication: red, green, yellow, blue or white LED* Inbuilt diode for suppressing unwanted peaks while relay opening and RC element against disturbances 1- MODULE, DIN rail mounting

Switching current: 0.5, 11, 15 A

... available for holding or indicating as follows: E40, 11A, 250V AC; E60, 15A, 250V AC and 1/2A, 125V DC; E100 and E150, 15A, 480V AC and 1/2A, 125V DC. Other auxiliary contact ratings are available.

... switch operating contacts in response to impulses from a solid-state electronic timing circuit. Automatic Reclosing Relay Protective relays are often interested from unwanted opening due to temporary ...