- Hydraulics - Pneumatics >
- Pump >
- Electric pump >
- Witte Pumpen
Witte Pumpen electric pumps
Flow: 12 m³/h
Power: 0.37, 0.25 kW
Weight: 8, 12 kg
The FL20C centrifugal pump is well known for its small size and high performance. Despite their small size, these pumps can provide flows up to 12 m3/h with good outcomes. FL20C pumps ...
... consisting of Water Pumps, Thermostats, Thermostat Kits, Switches & Sensors, Coolant Flanges and Radiator Caps. In the quest to reduce engine emissions, there is a growing trend among ...
Flow: 0 m³/s - 40 m³/s
Pressure: 0 bar - 40 bar
Fluid temperature: 0 °C - 120 °C
Vertical immersion pumps are multistage centrifugal pumps for installation on the mounting flange of tanks. PUMPED LIQUIDS Light, non-explosive, clean or contaminated liquids. Water Cutting fluid Lubricants
Arancia Pumps
Flow: 0 m³/h - 110 m³/h
Pressure: 0 bar - 40 bar
Fluid temperature: 0 °C - 120 °C
Vertical in-line pumps Vertical and multistage centrifugal pumps. The in-line design enables the pump to be installed on pipes where the suction and discharge ports are on the same horizontal ...
Arancia Pumps
Flow: 0 l/min - 650 l/min
Pressure: 0 bar - 100 bar
Fluid temperature: 0 °C - 60 °C
High pressure pumps High pressure spindle pumps. Solution for deep boreholes and the high pressure clearance of chippings. PUMPED LIQUIDS Light, non-explosive, clean liquids with at least 5% of ...
Arancia Pumps
Flow: 110, 140, 70, 90 us gal/min
Head: 19.8, 18, 21.3, 12 m
Power: 0.75, 1.5, 0.4 kW
... •High-torque, capacitor-start motor •Motor thermal overload protection •Outer jacket for continuous motor cooling •Silicon Carbide upper and lower mechanical seals Lightweight and portable electric ...
Alcon
Flow: 5.5 l/h - 1,000 l/h
Pressure: 10, 40 bar
Power: 0.18, 0.25, 0.37, 0.55, 0.75 kW
... Manually with graduated knob Motor speed regulation via inverter Electric servomotor adjusts pump flow rate remotely Aluminium housing: for excellent operating performance even in ...
Flow: 0.21 m³/h - 67.69 m³/h
Pressure: 39 bar - 1,146 bar
Power: 2.2 kW - 110 kW
3C Triplex Pumps Series Process pumps for high-pressure duties A flexible, robust and reliable solution to pumping high temperature, abrasive and viscous liquids in a multitude of industrial applications, ...
Flow: 1.6 l/min - 25 l/min
Pressure: 0 bar - 10 bar
Head: 0 m - 100 m
The gear pumps of the PM series have a wide range of models that allow the transfer of flow rates ranging from 25 l / min to 280 l / min. This type of pumps are suitable for use in the most diverse sectors ...
Anglada Pumps
Flow: 2.5 l/min - 46.5 l/min
Pressure: 0 bar - 10 bar
Head: 0 m - 100 m
... consequently, a loss of performance. That is why the PM V103 pump has a triple heating chamber to ensure the homogeneous temperature. The system sealing is made through a food packing and the drive system ...
Anglada Pumps
Flow: 0.1 l/min - 0.5 l/min
Pressure: 0 bar - 10 bar
Head: 0 m - 100 m
Anglada Pumps
Flow: 40 us gal/min
Pressure: 10 psi
WSP33 (WSP33K1AA ) FEATURES 1/3hp 115V submersible pump Top discharge 40 gal./min capacity Lightweight durable stainless steel casing Automatic non-mercury float switch Rated for continuous use
Honda Power Equipment
Flow: 110 us gal/min
Pressure: 14 psi
Power: 0.5 ch
WSP50 (WSP50AA ) FEATURES 1/2hp 115V submersible trash pump Side discharge 110 gal./min capacity Solids handling capability up to 2" Automatic non-mercury float switch Rated for continuous use
Honda Power Equipment
Flow: 70 us gal/min
Pressure: 0 psi - 15 psi
WSP73 3/4 hp 115V submersible pump Top discharge 74 gal./min. capacity Automatic non-mercury float switch Double mechanical seal construction Rated for continuous use 50 ft cord
Honda Power Equipment
Flow: 0 m³/h - 1,000 m³/h
Power: 1.3 kW - 310 kW
... Excellent flow passing properties Motors with high power density Robust and reliable COMPACT CHOPPER PUMPS CUT SUMP PROBLEMS DOWN TO SIZE The Flygt F 3069 chopper pump is specifically ...
FLYGT
Pressure: 63 bar
Power: 0.18, 0.12 kW
Fluid temperature: -10 °C - 60 °C
The pump is designed for the lubrication with plastic grease or oil of machines and equipment requiring continuous lubrication in small quantities. The lubricant is fed to each receiving point via ...
Zaklady Automatyki POLNA S.A.
Flow: 0.15, 0.25 l/min
Pressure: 400, 200 bar
Power: 0.75 kW
... conditions. The pump consists of the following subassemblies: Central lubrication a tank with a grease feeding device, a drive train consisting of an electric motor, a ...
Zaklady Automatyki POLNA S.A.
Flow: 0.4, 0.2, 0.1 l/min
Pressure: 200, 320, 400 bar
Power: 1.1 kW
... equipment and work conditions. The central lubrication pump consists of the following basic assemblies: a grease tank with a feeding device, a drive unit consisting of an electric ...
Zaklady Automatyki POLNA S.A.
Flow: 10 m³/h - 1,400 m³/h
Weight: 142 kg - 1,956 kg
The Linatex pump, type III R, belongs to the latest generation of successful wear-resistant and corrosion resistant slurry pumps and has an improved efficiency. It has in practice proven durable Linatex ...
Flow: 2,600 m³/h
Pressure: 10, 15 MPa
Head: 300 m
... mounted. Axial suction, radial discharge, suction and discharge flange pressure rating is the same. The axial force in the pump is balanced by the optimally designed sealing ring and balance hole, the paired tapered ...
SOURCE Pumps & SYSTEMS Co., Ltd.
Flow: 1,000 m³/h
Pressure: 5 MPa
Fluid temperature: 30 °C - 230 °C
... located on the same horizontal line, vertical installation, small footprint, easy installation. The pump has a separate bearing frame and the bearings are grease lubricated. The pump ...
SOURCE Pumps & SYSTEMS Co., Ltd.
Flow: 2,000 m³/h
Pressure: 2.5 MPa
Head: 160 m
Single-stage radial impeller, horizontal, radially split volute, foot mounted. Axial suction, radial discharge, suction and discharge flange pressure rating is the same. Dimensions and performance meet and exceed ISO2858 requirements. ...
SOURCE Pumps & SYSTEMS Co., Ltd.
Flow: 72 l/h - 2,200 l/h
Pressure: 0 bar - 8 bar
Fluid temperature: 85 °C - 130 °C
... flexible handling by means of lifting bows. Discharge pumps for Fluidbag and barrels A specialty of ipp Pump Products GmbH is the progressive cavity pump FLB, which as a horizontal ...
Flow: 0 m³/h - 1,850 m³/h
Head: 0 m - 120 m
... operating in optimal condition. The pump utilizes a flexible coupling, which allows the internal pump component to be removed without dismantling of the motor from the pump ...
Pressure: 51.7, 34.3 MPa
Power: 596, 373, 969, 745, 1,193 kW
Length: 3,639 mm - 5,475 mm
Mud pump is used to circulate drilling fluid while drilling, it is the core part of drilling fluid circulation system, and it is composed of power end and fluid end. The products conform to API Spec ...
Flow: 20 l/min
Pressure: 20 bar
Fluid temperature: 60 °C
Three-diaphragm pump with reinforced Polypropylene circuit, Kynar/AISI 316 valves (LFP version), AISI 316 diaphragm mounting components, Viton seals. Version: SP (cylindrical with shaft key), CR (reduction gearbox ...
Annovi Reverberi
Flow: 55, 71, 87 l/min
Head: 23, 16, 10, 7 m
Power: 450, 250 W
... /off switch integrated low voltage release is intended to prevent an uncontrolled start of the drum pump motor after a power failure or voltage drop and thus guarantees ...
Dr. Jessberger GmbH
Flow: 82, 61 l/min
Head: 9, 20 m
Power: 460 W
... drum pump motor is characterized not only by its light weight (2,9 kg) but also by its elegant design and ease of use. The non-stationary and stationary usable drive is particularly suitable ...
Dr. Jessberger GmbH
Flow: 55, 66 l/min
Head: 7.5, 15 m
Power: 400 W
... drum pump motor is characterized not only by its light weight (2,9 kg) but also by its elegant design and ease of use. The non-stationary and stationary usable drive is particularly suitable ...
Dr. Jessberger GmbH
Flow: 0 l/min - 4,656 l/min
Pressure: 0 Pa - 2,000,000 Pa
... function as a process and/or CIP pump, which helps in reducing maintenance time and costs, with the advantage that it is suitable for abrasive products like toothpaste. It can handle air up to 60%, which prevents pump ...
Q-Pumps
Flow: max 1200.0 us gal/min
Pressure: max 8.0 bar
Head: 310'00"
QC Series Centrifugal pumps are built and designed in compliance with 3A Standards, with the following characteristics: Open Impeller Volute casing with central suction Fittings: Clamp (standard), Flange, NPT thread, ...
Q-Pumps
Flow: 70 us gal/min - 850 us gal/min
The QTS is a twin screw pump, 100% sanitary use and ideal as a CIP and Process pump, which reduces time and maintenance costs Certifications: 3-A, FDA and EHEDG Characteristics - Self-priming - ...
Q-Pumps
Flow: 1.2 l/h - 35 l/h
Pressure: 0 bar - 10 bar
Power: 33, 20 W
... deformable drive diaphragm. This membrane is connected via a connecting rod fixed to the drive magnet and so is deflected to the suction and pressure strokes. Solenoid diaphragm pumps ...
Flow: 66 l/min
Pressure: 1.5 bar - 2.8 bar
Head: 34, 45, 53 m
Self-priming centrifugal multi-stage pump For pumping rainwater out of storage tanks Rubber feet to suppress pump vibration and noises Integrated stainless-steel dirt trap Suction end with 1“ nozzle Optionally ...
Flow: 0 m³/h - 120 m³/h
Pressure: 0 bar - 35 bar
The FKL series features circumferential piston pumps designed for special pumping applications. These pumps operate at 35 bar maximum pressure with up to 120 m3/h flow rates. Available in ten different ...
FRISTAM
Flow: 20 m³/h - 180 m³/h
Pressure: 20, 25 bar
When developing this exceptional pump, we intended to set new standards in double-screw technology. We started by rethinking functional principles from the ground up and eliminated previously known deficiencies typically ...
FRISTAM
Based on the proven centrifugal pumps of the Fristam FP range, the shear pump has a new, efficient mixing method. A rotor/stator system which operates at tip speeds of up to 38 m/s is utilized instead ...
FRISTAM
• Flow rates and prevalence on request • Made of PP or PVDF
• For applications inside or outside the tank • Made of plastic: PP – PVC • Shaft made of: AISI316 – coated titanium
• Magnetic drive pump made of plastic material • Closed or open impeller pump in AISI304 or AISI316 • Connectors in PP, PVC, PVDF • Pumps with membrane in plastic material or steel
... any leakage. These pumps should always be used together with a primary pump increasing the total flow rate at low operating pressures and reaching a great improvement of the final pressure. Typical ...
DAB Technology Pte. Ltd.
Claw Pumps The new PA.155 Claw pumps create air volume and transfer it through the intake duct to the outlet duct by means of the rotation of two claw shaped rotors in a moulded chamber. The dry running ...
DAB Technology Pte. Ltd.
Power: 0 kW - 150 kW
CENTRIFUGAL PUMP (NM) ASV Stubbe produces pumps for aggressive or corrosive liquids. We offer an extensive product range of horizontal or vertical pumps made of the most resistant materials ...
DAB Technology Pte. Ltd.
Flow: 42 l/min - 129 l/min
Pressure: 500, 400, 320 bar
Power: 0 kW - 75 kW
HFA/HFC fluids Non-oily water/clear water Mine water Industrial water Descaling water Neutral fluids with a viscosity of 0.5 – 4.0 mm²/s
Hauhinco
Flow: 201, 167, 266, 221, 278 l/min
Pressure: 160, 210 bar
Power: 0 kW - 75 kW
HFA/HFC fluids Non-oily water/clear water Mine water Industrial water Descaling water Neutral fluids with a viscosity of 0.5 – 4.0 mm²/s
Hauhinco
Flow: 103 l/min - 163 l/min
Pressure: 365, 575, 465 bar
Power: 0 kW - 110 kW
HFA/HFC fluids Non-oily water/clear water Mine water Industrial water Descaling water Neutral fluids with a viscosity of 0.5 – 4.0 mm²/s
Hauhinco
Flow: 10 m³/h - 30 m³/h
Pressure: 12 bar
Power: 5.5 kW - 11 kW
The “Dragon ME” series represents the evolution of the Dragon piston pumps series with the addition of the membrane unit in case of pumping highly abrasive liquids. Flow ranges: from 20 to 30 mc / h - in single mode ...
Flow: 1 m³/h - 10 m³/h
Pressure: 12 bar
Power: 1.5 kW - 5.5 kW
Piston Pump - "Libra" Series from 1 to 10 mc/h Pressure up to 15 bar Many materials configuration For pressure transfer of viscous liquid For sludge feeding of Filterpress For chemical Industry, metal finishing ...
Flow: 0 m³/h - 450 m³/h
Head: 0 m - 100 m
Power: 4, 3 kW
Standardized centrifugal pumps type NB are single-stage horizontally mounted pumps. They are characterized by a maintenance-friendly design and can be used in a wide variety of applications. 18 sizes ...
SCHMALENBERGER GmbH + Co. KG
Flow: 0 m³/h - 42 m³/h
Head: 0 m - 42 m
Power: 4, 3 kW
... high pressure centrifugal pumps type ZHB are horizontally mounted pumps. They are characterized by a minimum space requirement. Optionally, this series can be equipped with two or three pressure outlets. ...
SCHMALENBERGER GmbH + Co. KG
Flow: 0 m³/h - 120 m³/h
Head: 0 m - 58 m
Power: 4, 3 kW
... centrifugal pumps of the series SM are single-stage horizontally mounted pumps. Because of their robust and durable design the SM pumps can be used in a wide variety of applications. ...
SCHMALENBERGER GmbH + Co. KG
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining