|
|
Multi-component force measurement places high demands on the measuring device. The characteristics of the force vector to be measured largely determine the result. The size and direction of the force application point, as well as the dynamics, should have as little effect as possible on the process.
With the new Kistler Type 9327, 9347, 9367 and 9377 sensors, our company's established experience and know-how is now available even for multi-component force measurements carried out by the customer. The precisely preloaded measuring elements are easy to fit and, as they come ready calibrated from the factory, they can be used immediately for multi-component force measurements.
|
|
Series 261A
Triaxial 3-component dynamic force link, ICP®
- Automotive Chassis and Other Vehicle Dynamic Measurements
- Monitor Cutting tool suppliers Forces and Detect Tool Wear
- Provide Feedback for Force Limited Vibration testers
- Measure Input Forces for Modal and Structural Testing
- Measure Impact Forces During Drop Testing and Crash Testing |
|
DS Europe produces load cells with built-in analog and digital electronics.
Measuring ranges:from 0 to 6Kg up to 500tons max.
Outputs: CANOpen, RS485, RS422, 5V, 10V, 4-20mA, 2mV/V.
Advantages: high resolution (A/D industrial converter 24bit max.), high sampling rate (from 7,5 upt to 960Hz max.), electrical noise protection, compactness, digital alarms, digital filter, zeroing, easy to service (overload memory).
Applications: automation, textile machines, medical machines, machine tools, industrial presses, vehicles, weighing, food machines, quary machines, agricolture machines, research, machines working paper-wood-plastics-rubber etc. |
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cable (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
DS Europe manufactures industrial load cells with built-in CE marked electronics with analog or digital outputs.
All load cells with non amplified output 2mV/V have a built in calibration circuitry that electrically simulates a known value of force shown in a certificate ( making It easy and quick to calibrate with the external electronics getting the signal ).
Series 500QD single point load cells Ranges (tension and compression): from 0 up to ±2 ... 2000Kg FS.
Built-in electronics (option): analog or digital outputs.
Environmental protection: IP65.
Compensated against off-center forces.
Series AP7000 compact column load cells Series AP7000 tension and compression load cell.
Ranges: from 0 up to 250-500Kg 1-3-5-10-25-50-100 tons.
Built-in electronics (option): analog or digital outputs.
Environmental protection: IP65. |
|
DS Europe produces general purpose miniaturised load cells.
Measuring ranges: 0 to 3 up to 2000Kg.
Output: 2mV/V.
Applications: automation, medical machines ( dialisis, radiology, blood transfusion machines, dentist tools, hospital beds, stabilometry platforms etc.), textile machines, machines working paper-rubber-plastics, weighing, machine tools and wherever is required compactness. |
|
Sensortechnics is a leading manufacturer and distributor of a wide range of sensors and fluid control devices. The product portfolio includes basic industrial pressure sensors, rugged industrial transmitters, submersible level sensors and customised pressure sensing systems from 1 mbar up to 1000 bar as well as liquid level switches suppliers, oxygen, flow and force detectors. Additionally, Sensortechnics offers ultrasonic air bubble, air-in-line, liquid level and fluid monitoring sensors and detectors. Fluid control devices include miniature solenoid valves and diaphragm pumps manufacturers, electronic pressure governors and custom specific fluidic control systems.
Sensortechnics has more than two decades of experience in providing highly customised sensing products and in the development of complex integrated fluid control systems for OEM customers worldwide. |
|
Series 1515 Automotive Brake Pedal Effort Sensor for Vehicle Brake Development, Drivability & Handling, & Legislative & Safety
- Designed to measure force required to operate vehicle’s primary brake,
clutch, or floor-mounted emergency brake pedals
- High overload protection (500% of FS)
- Easy to install and remove
- Integral Cable; integral loading surface to reject off-axis loading errors
- Compact Design 1.19” (3.02 cm) overall height
- Temperature-compensated for +30 to +130 °F (-1 to +54 °C)
- Good resolution, linearity and repeatability in both static (constant force)
and dynamic (panic stop) loading events. |
|
For over a decade, FUTEK Advanced Sensor Technology has been supporting the Automotive Industries’ sensor requirements in endurance testing, validation, verification and qualification. Our Automotive Load batteries are designed to fit a wide range of applications from component testing to full assembly. Specialty products such as our Low Profile Spike Resistant Pedal Force transducer, Bi-Axial Stick Shift Sensor, and Compact Seat Belt Sensor are selected and fully trusted product throughout the Automotive Industry.
Any of our Automotive Load Cells can be easily modified or customized to meet your requirements. The standard models are often available in our stock making it available for 24 hour shipping. All Load cells and Force Transducers are manufactured in the US. All Sensors are available with in-line signal conditioned amplifier and or TEDS / IEEE1451.4 option.
• Custom Strain Relief
• One piece construction suitable for endurance testing
• Low Profile Height
• Light Weight
• Available in Tension, Compression, and Multi-Component Loads
• Removable Mounting Plate
• Spike Resistant
• Excellent Off Center Loading
• Operating Temperature of -60° F - 200° F
• Capacity ranging from 10 lb to 100,000 lbs
• Utilizes Metal Foil Strain gage Technology
|
|
The OIML certified beam load cells SD are used for general weighing in tough environments, in bench- and platform scales, belt scales and in production equipment.
* Accuracy classes C1, C2, C3, C6 (MI10) to OIML R60
* High overload and sideload capacity 250 to 1.000 %
* Uncomplicated mechanical installation without protecting devices
* Patented high reliability sensor - stainless steel, laser welded to IP68
* Uncomplicated electrical installation - coax cable only
* RS485, Profibus DP, DeviceNet, Modbus to PLC SUPPLIERS's, PC's, etc. and OIML certified weighing displays
* Withstands welding voltages and ESD to IEC 1000-4-4
* ATEX approved version available (type SDE)
|
|
FLINTEC load batteries are designed to meet the most stringent
accuracy requirements. Certifications have been obtained
from Weights & Measures Authorities, worldwide.
Bending Beam load cells are available in the capacities 500lb to 10kN and include Accuracy Classifications GP,
C1, C3, C3 MI 7.5, C4 and C4 MI 7.5 according to OIML R 60;
NTEP nmax=5000.
They offer total stainless steel construction and complete
hermetic sealing, making them suitable for use in the toughest industrial environments.
The Flintec calibration technique (in mV/V/Ω) eliminates time consuming corner calibration in multiple load cell systems.
ATEX versions available. |
|
- Handheld Readouts.
- Made from a Lightweight Aerospace Alloy.
- Available Hermetically sealed for use in wet conditions.
- Tare, Peak and Reset facility.
- Units have a 5 metre cable close coupled to a 4 digit 15mm LCD display.
- All units are calibrated to comply with ISO 7500-1: 2004.
- The accuracy of the cells are better than 1% of applied load.
- The power source is a 9V PP3 battery, can be supplied for
mains power if required (240v).
- 12 Month Guarantee, subject to conditions.
- Complete with carry case. |
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial cabling (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen industrial load cells is covered worldwide by a number of patents. |
|
FLINTEC load batteries are designed to meet the most stringent
accuracy requirements. Certifications have been obtained
from Weights & Measures Authorities, worldwide.
Rocker column load cells are available in the capacities
7.5 t to 300 t and include Accuracy Classifications GP, C1, C3, C4, and C3 MI 8 according toOIML R60; NTEP nmax=10000.
They offer total stainless steel construction and complete
hermetic sealing, making them suitable for use in the toughest industrial environments.
This load cell design, in combination with a low cost self
aligning rocker assembly, unites excellent load introduction
with a low profile outline.
The Flintec calibration technique (in mV/V/Ω) eliminates time consuming corner calibration in multiple load cell systems.
ATEX versions are availiable. |
|
Force gauges manufactured in US by FUTEK Advanced Sensor Technology (FUTEK), a leading manufacturer producing a huge selection of Load Cells, utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gage technology.
A Load Cell is defined as a transducer that converts an input mechanical force into an electrical output signal. Load Cells are also commonly known as Load Transducers or Load Sensors. |
|
- A suitable loadcell can be selected among the various
models of the loadcells.
- Convenient for measuring in dangerous area due to the
separated loadcell model.
- Convenient for measuring in small area. |
|
-Robust technology and design
-High tolerance of up to 1.000 % overload
-Plug-and-play installation
-High accuracy, High resolution
-Hermetically sealed to IP68
-Interfaces: RS485, Profibus DP, DeviceNet, 4-20 mA, 0-10 V
-Digital filters
-ATEX certified
-3 years warranty
-Patented worldwide
The shockproof digital load cell is based on a capacitive measurement principle where a non-contacting ceramic sensor is mounted inside the load cell body. As the load cell contains no moving parts and the sensor is not in contact with the load cell body, the load cell tolerates shocks, torsion, and very high overloads and sideloads. Therefore, the mechanical installation of the load cell can be done without expensive and complicated mounting kits and overload protection devices.
The electrical installation of the digital load cell is pure plug-and-play as the signal from the non-contacting sensor is directly converted, compensated and calibrated by a microprocessor to a digital load cell output in grams, kilograms, or Newton. Measurements and status codes are transmitted as RS485 data on a single wire coaxial wiring (RG-58) which may be up to 100 meters long.
The technology and mechanical design of the Eilersen load cells is covered worldwide by a number of patents. |
|
Sensors of industrial weighing in shearing, entirely welded stainless and seals IP68.
Sensor 3510 is especially used for applications of weighing on hoppers, plates of weighing, and applications of measure of force.
Exist of 300 kg to 5000 kg with homologation IOLM in 3000 divisions |
|
Eilersen Electric also offers its expertise to customers with special requests where the capacitive technology can often be the solution to challenging applications.
Examples of customized solutions are: Stress measurements in roller bearings supplier, Web tension measurements in paper and plastic foil manufacturing equipment, Monitoring of construction equipment, Load measurements in commercial vehicles etc.
* Classes OIML C1 to C6
* Atex versions
* Uncomplicated mechanical installation without protecting devices
* High overload and sideload capacity up to 1000 %
* Patented high reliability sensor - stainless steel, laser welded to IP68
* Uncomplicated electrical installation - coax cable only
* RS485, Profibus, Devicenet, CAN bus to PLC MANUFACTURERS's, PC's, etc. and EE instrumentation
* 32 bit data word does away with dead weight compensation
* Withstands welding voltages and ESD to IEC 1000-4-4 |
|
Utilising many years of load cell and transducer design and manufacturing experience, Flintec is able to provide a custom strain gaging service on customer supplied components. From low volumes through to serial production, Flintec can provide a cost effective and reliable service to OEMs.
For customers requiring solutions to force measurement problems, Flintec is able to supply custom designed and manufactured load batteries, transducers, application parts and electronics or even complete sensing solutions.
Flintec provides
- Sensing element design - CAD, FEA and 3D solid modelling
- Production of prototypes - in-house Cnc machining centre and heat treatment
- Strain gage installation - modern, well equipped production facilities
- Calibration - temperature calibration and force calibration using hydraulic and dead weight test machines
- Electronics - internal or external signal conditioning electronics
- Rapid turnaround - all processes under one-roof
- Design verification and validation - tailored to meet the needs of the client |
|
Responding to specific projects is a part of our strength.
Are you looking for a solution for which no available component is to be found on the market? We will help you solving your problem by means of one of the special load cells we already realized or by developing a custom made model. Our design team will assist you in your project, from its very beginning till its complete realisation. Designing and realizing new solutions are our specialties; it belongs to our company's culture. During the last years, we have developed more than 1500 models and applications, from single part till medium and great serial production. We can present you a documented proposal including quotation within short time.
Even a part of an existing machine can, under certain conditions, become a force transducer measuring tension or compression. Transducers that will respond to your need at particularly competitive prices.
|
|
| Our load accumulator uses proprietary sputtered thin film strain gage technology to create a rugged sensor with exceptional long term stability. These highly sophisticated sensors are manufactured in high quantities using state-of-the-art equipment. |
|
Utilising many years of load cell and transducer design and manufacturing experience, Flintec is able to provide a custom strain gaging service on customer supplied components. From low volumes through to serial production, Flintec can provide a cost effective and reliable service to OEMs.
For customers requiring solutions to force measurement problems, Flintec is able to supply custom designed and manufactured force gauges, transducers, application parts and electronics or even complete sensing solutions.
Flintec provides
- Sensing element design - CAD, FEA and 3D solid modelling
- Production of prototypes - in-house Cnc machining and heat treatment
- Strain gage installation - modern, well equipped production facilities
- Calibration - temperature calibration and force calibration using hydraulic and dead weight test machines
- Electronics - internal or external signal conditioning electronics
- Rapid turnaround - all processes under one-roof
- Design verification and validation - tailored to meet the needs of the client |
|
Responding to specific projects is a part of our strength.
Are you looking for a solution for which no available component is to be found on the market? We will help you solving your problem by means of one of the special load cells we already realized or by developing a custom made model. Our design team will assist you in your project, from its very beginning till its complete realisation. Designing and realizing new solutions are our specialties; it belongs to our company's culture. During the last years, we have developed more than 1500 models and applications, from single part till medium and great serial production. We can present you a documented proposal including quotation within short time.
Even a part of an existing machine can, under certain conditions, become a force transducer measuring tension or compression. Transducers that will respond to your need at particularly competitive prices.
|
|
Utilising many years of load cell and transducer design and manufacturing experience, Flintec is able to provide a custom strain gaging service on customer supplied components. From low volumes through to serial industrial production, Flintec can provide a cost effective and reliable service to OEMs.
For customers requiring solutions to force measurement problems, Flintec is able to supply custom designed and manufactured load batteries, transducers, application parts and electronics or even complete sensing solutions.
|
|
Responding to specific projects is a part of our strength.
Are you looking for a solution for which no available component is to be found on the market? We will help you solving your problem by means of one of the special load cells we already realized or by developing a custom made model. Our design team will assist you in your project, from its very beginning till its complete realisation. Designing and realizing new solutions are our specialties; it belongs to our company's culture. During the last years, we have developed more than 1500 models and applications, from single part till medium and great serial industrial production. We can present you a documented proposal including quotation within short time.
Even a part of an existing machine can, under certain conditions, become a force transducer measuring tension or compression. Transducers that will respond to your need at particularly competitive prices. |
|
|
Weight sensors, Force sensors, Torque sensors
