|
|
Baer momentary switch
Characteristics:
• single pole
• quick connect
• snap- in mounting or central-fixing
Rating: 250 VAC, 0.2 [0.2] A
Dimensions (mm):
various Actuator plunger
Approvals ENEC
|
|
push-button switch Baer
Characteristics • double pole
• on, off
• quick connect
• PCB terminals
• extended life (5E4)
• customised mounting
• momentary function optional
• temp. 100°
Rating 250 VAC, 8 (8) A
Dimensions (mm) 13.5 x 19
Actuator • push button
square 6 mm
Approvals ENEC
|
|
|
|
|
|
PAN3VB
Format DIN 48x96
3 indicators
2 switches
Indicators part :
It makes it possible to announce :
- 3 gathered information.
- "Start, stop, default".
- "presence of the 3 three-phase tensions" of an electric departure.
Supply :
- Low voltage (12Vac/dc, 24Vac/dc, 48Vac/dc).
- Hight voltage (130Vdc, 220Vac, 380Vac).
Equipped with 3 removable indicators LED "high luminosity" (possible colors: green, yellow, red, blue, white), of its connector scewless removable, its test lamp optional outside, it is very easy to install and will save to you an precious time.
Option :
Lamp test output.
Switches part :
Elements with exits on terminals.
Available modulary elements :
- Switch 2 permanent positions.
- Switch 2 positions fix with reminder.
- Inverter 2 permanent positions stables.
- Inverter 3 positions.
- Indicators.
B1200
Format DIN 144x144
12 elements
Unit for command to cabinet or switch board
A high concentration of control units allows. Elements with exits on terminals.
Available modulary elements :
- Switch 2 permanent positions.
- Switch 2 positions fix with reminder.
- Inverter 2 permanent positions stables.
- Inverter 3 positions.
- Indicators.
|
|
Control units are switching devices which close or open electrical circuits.
A control unit is a combination of an actuator and a contact block.
The various product ranges are supplemented with signal indicators, which consist of a signal indicator element and a lamp socket.
RAFIX 16, mounting hole diameter 16,2 mm
RAFIX 16 F, monting hole diameter 16,2 mm, extremely low profile
RAFIX 22 QR, mounting hole diameter 22,3 mm
RAFIX 22 FS, mounting hole diameter 22,3 mm, mounting depth only 9,2 mm
|
|
Handels with functions:
With mechanical, pneumatical, or electrical function. At the electrical version all connections of buttons, emergency stop and LED will be lead out of the handle, that the customer can use all functions individually.
|
|
Buzzer
Switch for railway application (momentary/maintained) Knob Set for rotary switches
Pushbutton Heads Membrane Pushbuttons
Pedal Switches
Toggle Heads
Pilot Light Head/Pilot Light
Emergency-stop Heads
Knob Set for potentiometers
Mushroom Heads
Key Actuators
Selector Heads (momentary/maintained)
|
|
Push buttons and selector switches
- Metal and plastic, with quick installation by simple rotation
- Standard IP65 front degree of protection
- Highly conductive contacts
- Contact operation: double breaking action, direct opening operation and self cleaning action.
Signal towers Ø70mm
- Modular and combinations up to 7 modules
- Steady or blinking light, pulsed or continuous sound modules.
Signal beacons Ø62mm
- Steady or blinking light , pulsed or continuous sound modules.
|
|
|
|
|
|
MANUAL PILOT DEVICES
Large range of industrial push-button panels, designed in 2 distinct series, 22 dm and 30 dm, for industrial uses where sturdiness and reliability have been incorporated with a simple intuitive modularity. The contact elements of both series have electrical characteristics among the best available on the market and offer elevated performances; they can also be used in heavy industry sectors such as building, railway, shipping, automobile, tertiary.
The range includes:
- normal push-buttons
- luminous push-buttons
- step by step push-buttons
- push-buttons with rubber cover,
- emergency mushroom push-buttons
- rotation release push-buttons
- push-buttons with keys
- pilot lamps in different versions
- knob selector switches
- lever selector switches
- key selector switches
- padlockable push-buttons
- safety push-buttons
- fixed position manipulators
- temporary position manipulators
- accessories: led lamps
- accessories: wiring elements
- accessories: labelling machine plates
- accessories: heat transfer printers
|
|
The L6 series of pushbuttons and pilot devices comprise a "full line" solution to 16mm panel cutouts. Available with termination as .110" solder-tab / quick-connect or with PCB terminals. Locking lever removable contacts facilitate wiring harnesses or PCB applications to reduce wiring time.
Oversize button heads are now available for 16mm round, square, mushroom, selector and key switches. These larger buttons are ideal for gloved personnel and provide an alternative to 22mm pushbuttons if 10A contacts are not needed.
|
|
- Custom switches developed to customers' specifications
- Integrated modules combining several technologies
|
|
|
|
|
|
RF / Microwave Configurable Switching and Sub-systems
The Giga-tronics' ASCOR Series 8000 line of switch products are based on rugged electromechanical switches and microwave relays rated for use from DC to 40 GHz with low insertion loss and high isolation route signals under remote control to simplify and improve automated test systems.
The standard Series 8000 offers GPIB, USB and Ethernet LAN communication interfaces. A self-contained design, with built-in power supplies, microprocessor controller board and up to 256 relay coils, makes it very easy to implement a microwave switch system. It is design to host all combination of microwave relay switches, terminated or non-terminated: SPDT, SP4T, SP6T, SP8T or Transfer switches. With a standard SCPI commands, the control interface provides with the ASCOR Series 8000 for ease of operation and configurability.
With the flexibility and versatility design, the Series 8000 is ideal platform for custom applications. It is geared to control any or all of the various switch types on the front panel or host switching system internally. The Series 8000 switch assemblies are supplied in standard light-weight enclosure and can be mounted in half or full width rack from 2U to 7U. Easily removable switches allow reduced mean time to repair.
|
|
Series P76
Push-button switches
push-button operation
big, easy reading digits
snap on assembly using integrated pins for module mounting
optional decoupling diodes
Service life: 200.000 operations
Housing: thermoplast, color black
|
|
|
The Series 1025 Foot and Palm Switches are industrial-rated switches suited to applications where an operator must have both hands free to perform other functions or, where a highly visible switch is required for quick and easy operation. All of our switches are available in a wide choice of contact arrangements, ratings and enclosure styles. Industrial duty 4 way 5 port air valves are available for air control circuits.
|
|
|
EAO Emergency Stop switches are foolproof to EN 60947-5-5 and protected up to IP65. EAO emergency stop switches are available with slow-make switching elements and twist- or key- release options.
|
|
|
The MP720 positive opening position switch is a dependent-action, changeover, double-gap, contact element, which is connected by means of a cable directly overmoulded into the housing.
|
|
Several E-Stop switches fitting to the following product ranges:
- Pushbuttons LUMOTAST 25
- Control Units RAFIX 16
- Control Units RAFIX 16F
- Control Units RAFIX 22 QR
NEW: Control Units for AS-Interface bus.
|
|
It is assembled as an addition to a door latch
It avoids accidents related to the possible locking of an operator in a dangerous area.
It is equipped with a push button and safety contact block for the equipment emergency stop, the DEU adapts to all types of door latches and it is installed inside the protected area.
The emergency evacuation device forces ejection of the latch. The pushing the button frees the latch and stops the machine immediately due to a 2 0 safety contact and permits opening of the access by pushing the door.
EMERGENCY EVACUATION DEVICE
In case of emergency:
1 – The locked-in operator presses the push button.
2 – The latch separates from the DEU.
3 – The safety contact opens the emergency stop circuit.
To re-start, it will be necessary to unblock the latch after the installation is safe.
The latch must be assembled in the fixed part of the access.
Options
- Without contacts
|
|
TH-Contact emergency stop button
Découpe de montage (mm) : Ø 16,2 / Ø 22,5
Caractéristiques :
• conforme aux directives EN-418
• étanchéité IP66 ou IP67
• déverrouillage par rotation, par traction ou à clé
• calotte à disque jaune (en option)
• 1 contact à fermeture et 1 contact à ouverture, 2 pôles de contacts à ouverture
Pouvoir de coupure 250 V/CA, 6 A
Dimensions (mm) : Ø 27 x 49 ; Ø 40 x 61,7
Organe de commande :
• capuchon coup de poing rouge
• clé KABA
Homologations : IEC 947-5-1/947-5-5
|
|
Technical description
The switch is in "ON" position with the red knob extended. Pushing the knob instantly opens the circuit and the permanent magnetic blowout ensures that inductive arcs are extinguished. Because of the built-in permanent magnetic blowout correct polarity of line termination is required. In case of electrical or mechanical damage of the switching element, it can be changed easily, which guarantees an extended life of the unit as well as cost effective maintanance. When fitted with the optional keyswitch, the S132 may be locked in the "OFF" position so as to prevent unauthorised use of any equipment.
Features
- Momentary action mechanism
- Magnetic blowout
- Two definite bistable positions
- Cylinder lock available
- Auxiliary contact available
|
|
Even redundant, secure emergency-stop chains are ineffective unless the contact block is accurately connected with the emergency-stop button. The patented safety contact blocks of Schlegel Elektrokontakt are the response to this danger that may occur e.g. due to a negligent assembly or a mechanical damage.
In such an emergency they ensure that the emergency function is activated and that the installation is immediately shutdown. It can only be started up again after trouble-shooting.
The contact blocks are available with screw connections or Faston terminals and do have positive opening contacts acc. to IEC60947-5-1. They can be supplied with one or two channels and also, once combined with the relative E-stop button, in a foolproof version acc. to EN60947-5-5 and EN418. The high-quality contact elements allow reliable switching even of low currents (5mA at 24V or less). They are available as conventional contact blocks as well as for the AS-Interface-Bus (Safety@Work).
|
|
The XA and XW series of Emergency Stop switches include a revolutionary new technology called "safe break action" that will change the way E-Stop switches are designed. This innovative concept provides greater levels of human safety and is the first of its kind in the world.
Conventional E-Stop switches are designed with spring pressure on the Normally Closed (NC) contacts, keeping them in the closed position and allowing the machine to operate. Improper installation or excessive force to the stop button in an emergency may break or dislodge a vital part, causing the spring loaded contact to stay closed. This situation renders the E-Stop incapable of stopping the machine and can lead to catastrophic events, personal injury and possible loss of life.
|
|
The XA and XW series of Emergency Stop switches include a revolutionary new technology called "safe break action" that will change the way E-Stop switches are designed. This innovative concept provides greater levels of human safety and is the first of its kind in the world.
Conventional E-Stop switches are designed with spring pressure on the Normally Closed (NC) contacts, keeping them in the closed position and allowing the machine to operate. Improper installation or excessive force to the stop button in an emergency may break or dislodge a vital part, causing the spring loaded contact to stay closed. This situation renders the E-Stop incapable of stopping the machine and can lead to catastrophic events, personal injury and possible loss of life.
|
|
|
If you need a compact rugged E-Stop or an E-Stop Station, there is a wide range of sizes and designs available. Options range from Illuminated push-pull to pushlock key reset.
|
|
Thermoplastic enclosure
Slow action
max. 2 contacts
Fixings to DIN EN 50047
Cable
|
|
|
The fire alarm devices of type 2014/2 are designed for manual triggering of alarms in hazardous areas. The II 2 G EEx emd IIC T6 type of protection allows the alarm to be operated in all Ex areas of the zones 1 and 2. The enclosure and the “increasedsafety” class of protection of the terminal room guarantee hazardous area protection. For reasons of explosion protection the switch contact and the modules are gas tight embedded. The housing is completely made of GRP. This ensures the high level of corrosion protection as well as Class II and III. No equipotential bonding necessary. Further design characteristics are profound ruggedness and minimum 8 mm thick walls.
|
|
Increased safety control stations
Polyester, EEx e II ou, ed IIC (IP65), 1 à 4 fonctions.
Increased safety enclosures EExe
|
|
The enclosure Series ConSig makes it possible to assemble different control units in a clear layout. Due to the fact that a wide range of control devices is available this enclosure covers a broad field of applications.
Explosion protection to CENELEC, IEC, NEC
For use in Zone 1 and Zone 2, Zone 21 and Zone 22
Standard and customized units
3 sizes available
Enclosures in glass fibre reinforced polyester resin
Up to 3 insertion points available per individual units
Options:
flanges in brass or moulded plastic
metal plates where metal cable entries are used
equipment identification plate can be attached
Different contact blocks available
Actuators in different forms available
|
|
|
|
Switches: Push-button switches, Control devices
