|
|
The ZCast Direct Metal Casting process provides the ability to produce cast metal parts from a CAD file significantly faster and less expensively than traditional prototype casting methods. The process involves professional printing molds and cores on a 3d printing directly from digital data, eliminating the pattern and core box production step in the traditional sand casting process. Metal is then poured into the 3D printed molds. The technology allows engineers to prototype parts in metal that were previously cost and time prohibitive.
The ZCast Process guarantees:
Extremely fast turnaround from CAD file to prototype metal part
Ability to print complex molds and cores
In-house mold making capabilities for product manufacturers
Simple metal pouring process for foundries |
|
| Nex Flow™ uses quality Haug static bars rather than cheap products because Haug static bars have been proven to last in difficult environments. The most fragile part of any ionization system is the static bar and Haug bars have proven themselves against others to have be rugged. |
|
SIMCO anti-static bars generate an electrical field through a high voltage on a row of ionizing emitter points. This causes the air molecules in the vicinity of the bar to break down into positive and negative ions. Because opposite charges attract, any charged material passing near the bar will attract ions until the charge on the material is neutralized. The materials will no longer be attracted to each other or to the machine parts. Attraction of dust, explosion or fire hazards and electrical shocks to personnel caused by static discharge are avoided.
|
|
The Series R50/R51 discharge bars are designed for the active discharging of disruptive static charges which develop in production processes.The bars are operated with an alternating voltage of 5 kV or 8 kV at 50…60 Hz and are designed for discharging moving surfaces.
Due to differences in the surface charge profiles on different materials, charges with both polarities are provided by the discharge bars. The corona section with its optimized geometrical configuration ensures
ultimate discharging efficiency.
Discharging can be supported by the L50 air profile. The advantages of the R50/R51 discharge bars:
• ultimate discharge range and hence enhanced depth effect
• high active discharge power through isolated ground conductors
• high safety standards through passive discharging power with deactivated power supplies manufacturer
• flexible installation
• no health hazards from electric shocks when making contact with the tips |
|
| The NEW PerforMAX 3 is the most advanced static control system available for monitoring static neutralizing performance. PerforMAX3 provides outstanding extended range performance to eliminate static charges even when installed 2" to 10" from webs (depending on conditions), and up to 20" on winders. |
|
| Static electricity is generated when paper and plastic webs, or sheets, are being processed. The dust particles adhere electrostatically to the surface. Quality deteriorates due to this type of contamination, particularly when the products have to be printed. Neutro-Vac systems have been designed to neutralise static charges and, at the same time, to remove particles as small as 25 microns, even at higher velocities! Each Neutro-Vac system is designed to meet specific production requirements. A variety of vacuum hood configurations and dustcollectors are available to ensure maximum cleaning and static neutralisation. For all web widths there are vacuum hoods for non-contact cleaning or professional brush cleaning. |
|
for chemistry and pharmaceutical use. Batch wise operating centrifuge for production scale for separation, filtration, washing, drying, clarifying, rinsing and impregnating.
The Type GZ is available for extraction of living cells.
The top-discharge centrifuge GZ follow the sizes of the technical wringers TZ and is available with a diameter up to 1250 mm. They are suitable for industrial use and big batches. The robust manufacturer of bearings in tree columns with low gravity centre make a low vibration running possible.
Benefits:
- Tree column suspension for low vibration running
- Mountable in floors with 3 fastening screws
- Long lifetime
- Favourable maintenance
- Easy installation and handling
- Numerous accessories
- Generously dimensioned bearings and motor |
|
Sweco offers a variety of decanting centrifuges: CD500, CD600, 414, and 518. These rugged, precision-built machines are designed to remove ultra-fine solids. Sweco centrifuge advantages include but are not limited to the following: low energy consumption, low cost, low polymer consumption, low cake moisture, low maintenance and a small footprint.
The Sweco CD500 and CD600 decanting centrifuges boast infinite speed adjustability of main bowl drive and backdrive (differential). Utilizing variable frequency drives on all motors allows low amperage start-ups and eliminates troublesome sheave changes. Stainless Steel wetted parts, tungsten carbide hard facing on bowl and scroll, as well as superior gear box construction make the CD500 and CD600 durable and rugged centrifuges.
Sweco's 414 and 518 centrifuges are the premier high-speed, decanting centrifuges for fluids cleaning and solids removal and product recovery applications. Built for industrial service, they are especially effective in environmentally sensitive areas. They deliver high recovery rates and efficient solids separation to significantly reduce disposal costs or reclaim valuable material from process streams. These centrifuges are also precision balanced for smooth operation over long periods at high RPM speeds, generating extremely high G-forces. |
|
CENTRIFUGAL FEEDERS
- BC 1000 Centrifugal Feeder
Depending on the type of parts to be distributed, the feed rate can vary from several parts per minute up to 10,000 parts per minute.
- Centrifugal Capsule Feeder
Saxo type with rate of 1,000 parts per minute
VIBRATION AUTOMATION
- Bols vibrants
- Centrifugeuses
- Vibrateurs linéaires
- Elévateurs
- Convoyeurs
- Périphériques
- Interlocuteur |
|
CEV-C series centrifuge is a kind of professional seal type filtering equipment which carries interval operation and hanged bag unloading at alien land. After the machine is stopped, the filtering bag and the liquid screen case are hanged out and carried to the fixed sith to unload the material.
The sections touching with the materials is made of normal stainless steel, special stainless steel, carbon steel, lining rubber or plastic or titanium alloy. Semi-auto, full-auto or MANUFACTURER OF PLC program control. GMP design available. |
|
ANGSTROM SCIENCES magnetrons are recognized as the new standard for thin film sputtering. In addition to their advanced features such as profiled magnets, turbulent water flow, and solid stainless steel construction, they offer a host of other performance efficiencies as well.
· Ultra Compact Design
· Easily Configured For Internal Or External Mount
· Available For Target Diameters 1 Through 16 Inches
· Quick & Easy Target Changes
· Low Pressure / High Power operation
· High Rates & Performance
· Greater Target Utilization
· Greater Film Uniformity – routinely ±3 to ±5 % range
Cathode Styles
Indirect cooled/Standard
Direct cooled
Direct cooled/Indirect cooled
Ultra High Vacuum
High Temperature
High Power Pulsed
High Power RF
CD/DVD
Rotary
Diode
Magnetic Options
Standard
High Utilization
Balanced
Unbalanced
Mag II
High Rate
High Power
Low Pressure
Mounting Options
Internal
External
Assembly Options
Single
Cluster
Custom |
|
ANGSTROM SCIENCES magnetrons are recognized as the new standard for thin film sputtering. In addition to their advanced features such as profiled magnets, turbulent water flow, and solid stainless steel construction, they offer a host of other performance efficiencies as well.
·Ultra Compact Design - Ideal For Retrofit Applications
·Easily Configured For Internal Or External Mount
·Available For Target Diameters 1 Through 16 Inches
·Quick & Easy Target Changes
·Low Pressure / High Power operation
·High Rates & Performance
·Greater Target Utilization
·Greater Film Uniformity – routinely ±3 to ±5 % range
TOTAL COMMITMENT
At Angstrom Sciences, we design, engineer, and manufacture our own complete line of magnetron sputtering cathodes for thin film deposition. It is our core business, and we are totally committed to making sure it is done right, every step of the way. So we can assure you of the quality and reliability of every product you buy from us. We stand ready to provide you any help you may need in specification, installation, start-up, and service.
|
|
Angstrom Sciences has developed a rotating cylindrical magnetron assembly that is compact, economical, and lightweight. And, by utilizing the patented technology already incorporated into our other magnetrons, we can provide you with excellent deposition, optimum target utilization (85%+), and inherent power savings.
The Onyx-Revolution has been customized for Flat Panel Display, Web Coating and Professional solar cell applications.
Complete assemblies are available from 3”-6” (76.2 mm-152.4 mm) in diameter and up to 154” (4 m) in length.
Other features include:
High Magnetic Field provides a low operating voltage for reduced power requirements.
An optimized electrical transfer design to deliver high power while avoiding arcing as well as reduced professional brush wear and debris.
An NW quick connect water-to-vacuum professional seal for Quick target changes, shorter down times and increased production.
A universal and cost effective magnet design with customized turnarounds.
Lightweight, easily-serviced product with off-the-shelf components for low-cost, long-term investment and reliability.
For more information on our rotating cylindrical design, complete our application questionnaire or contact a product manager at 1.412.469.8466.
|
|
Bussi Elettronica Industriale has manufactured patented Electronic Demagnetizers since 1969.
The high level of specialization and the continuous search for new solutions, guarantees top quality products and service. Demagnetising a metal part efficiently means contributing to the overall quality of the finished product.
The D-F series demagnetizers for FlexLink and the D-R series for Rotzinger fit into the conveyor supplier systems of the two brands. These models consist of an electronic housing with support and a demagnetizing coil.
The metal parts, usually rings and bearings suppliers, lie on the conveyer chain. The chain brings them into the coil and, when the piece is in the middle of the coil, the unit releases a capacity discharge without stopping the line. These models are also suited for all types of metal parts, of different dimensions and shapes.
The performances guaranteed by Bussi demagnetizers®, include: Minimum residual magnetism, Complete reliability, High productivity, Easy Motion with no magnetic impediment, Minimum power consumption, easy Adaptability to client’s production stations and customisation to apply Bussi technology to all demands – www.bussi.it
|
|
Ferrous materials and tools can become magnetised due to a number of causes, such as during sanding, grinding,
polishing, splicer, punching or cutting operations. However, this may also occur de to direct contact with (magnetic equip-ment), or even simply as a result of friction during processing. Whatever the cause, the result is the same: magnetised products that stick to one another and attract dust and swarf.
Besides demagnetising equipment Goudsmit also manufactures lifting magnets suppliers. For more information: please click here:
http://www.goudsmit-magnetics.nl/index.php?id=58&L=0 |
|
Even when residual fields are small, magnetization in a machine shop can cause problems with mechanical equipment. For example, ferrous grit attracted by magnetized tools and dies can cause excessive wear, and magnetized parts in assembly operations may hang up in feed chutes and magazines.
The only answer to such problems is demagnetization, which is accomplished by subjecting a magnetized part to a strong reversing magnetic field to disarrange the magnetic particles so that the required residual magnetic field is obtained.
Aperature Type Demagnetizer
Walker demagnetisers are designed to negate the effect of residual buildup with units matched to the size and material of the workpiece and engineered with control circuits that can effectively erase the residual fields. Walker has the only compensated units available that provide increasing field strength with increases in workpiece volume. |
|
| SIMCO offers a variety of charging bars and electrodes, depending on the specific applications and conditions. These bars are connected to a DC high-voltage industrial generator. A strong, ion-saturated electrical field around the single polarity high voltage points forces the material to a reference earth. The material is charged by the ions. Being attracted by different polarities, the surfaces temporarily cling together. There are various methods of temporarily charging materials electrostatically, using a SIMCO Chargemaster system. |
|
Many production processes and processing stages require materials to be bonded firmly for limited periods. The bonds must not leave any traces and must not be allowed to damage the material surfaces when the materials are eventually separated.
The adhesion through controlled static charges provides the ideal solution in these cases: the R130A / R131A / EXR130A charging bar is designed for applying the specific charge quantity. High-resistance materials such as paper, cardboard, plastics etc. are interlocked for brief periods or fastened to conductive surfaces, without the need to use industrial adhesives.
The design of the R130A / R131A / EXR130A charging bar allows its use in perfect harmony with the intended purpose. In combination with the Eltex high voltage professional generator models this effective charging system ensures productivity and quality improvements in the most varied production areas.
The charging bar EXR130A is available for use in the Ex zone. |
|
The point charging bar R23ATR is used wherever target-specific electrostatic charges need to be applied even at high temperatures. For instance in edge trim adhesion in flat film production.
Using the point charging bars R23ATR, both outer edge zones of the film are fixed directly downstream from the flat film extrusion die to prevent neck-in.
The point charging bar R23ATR can be operated with one, two or three emission tips. The tips are interchangeable. The geometry of the tips is adjustable depending on application. This means that the point charging bar R23ATR may be used horizontally or vertically even in confined spaces. |
|
Charging bar with senders connected to a resistance suitable to supply static charges.
Application :
- BLOW EXTRUSION PLANT FOR COIL CHANGES
- NO WOVEN EXTRUSION PLANT |
|
Expanders can be supplied as single- and multistage variants, in axial or radial configurations. With maximum inlet temperatures of up to 760 °C, an inlet pressure of 16 bar and outputs of up to 30 MW, they can be connected to a industrial generator or directly to the machinery train.
|
|
The EXR5C discharge bars are designed for the active discharging of disruptive static charges which develop in production processes in explosion hazard area.
The discharge bars and the power supply are used mainly in cases where disruptive static charges on fast-moving material webs impair production processes and need to be eliminated.
The bars are operated with an alternating voltage of 5 kV at 50…60 Hz and are approved for use in explosive atmosphere.
The advantages of the EXR5C discharge bar:
• ultimate discharge range and hence enhanced depth effect
• high active discharge power through isolated ground conductors
• high safety standards through passive discharging power with deactivated supplier of power supplies
• safety through function and malfunction monitoring
• continuous assembly slotting guarantees flexible installation |
|
Intrinsically-Safe Inspection Lamp ISL 200 / 400-Ex
The ISL 200-Ex and the ISL 400-Ex are robust, cable-connected inspection lamps for industrial use in explosion-prone areas for zones 1 and 21 according to norm 1999/92/EG (ATEX 137). The inspection lamps are especially notable for their bright and extremely long-lasting illuminants. |
|
The AHB380-D & AHB380-S series Hot Bond Controllers are an advanced composite, metal/metal bonding, manufacturing and repair system designed to meet all the demands of today's repair specifications but with tomorrow's requirements in mind.
|
|
Features and Benefits:
Bolttech is known for solving the toughest bolting problems found in the industrial world today. These basic practices go into every design and manufacturing detail of our stud tensioning line of tools. We design our tensioners with quality, simplicity and versatility of the specific application and user in mind. Bolttech's Delta Series bolt suppliers tensioners maximize efficiency and minimize size for specific single stud size applications.
- Patented high pressure/low friction professional seals are designed to outlast the competition and provide accuracy within .5% with a calibrated pumping unit.
- Environmentally friendly, using water-filled tensioning systems.
- The direct axial load is applied to the bolt and inaccuracies created through friction are alleviated. |
|
HYDRAULIC SUPPLIERS OF BOLT TENSIONING DEVICE
Output 155Kn to 4476Kn, Stroke up to 15mm, Suitable for Bolt Sizes M18 to M115 in various models
|
|
The RotaBolt® range provides you with either finger-tip, visual or remote measurement of tension throughout the life of the bolted joint. They surpass traditional tightening methods such as:
- Hydraulic Tensioners
- Flogging
- Torque Systems
which have severe control limitations and can result in unpredictable bolt tension and joint failure.
RotaBolts are setting new safety standards in a wide variety of sectors where joints are subject to fatigue, vibration, pressure containment and structural slippage.
|
|
| Over the years, Hydratight has developed many solutions for non-standard tensioner applications. A number are based around our existing reliable products, but we also have the ability through our experienced design engineering team to produce bespoke products to solve a wide range of tensioner based bolting applications. |
|
|
|
Manufacturing equipment 
