|
|
|
|
|
|
MILLENNIUM CATALYTIC BEAD COMBUSTIBLE GAS DETECTOR
The Millennium Series is an innovative line of industrial gas detectors. Its microcontroller provides fast, accurate and continuous monitoring of gases in extreme environments.
Using a modular design, Millennium products can easily develop and adapt to changing requirements, regulations and available technologies. No need to redesign an entire system - simply replace one inexpensive "personality module" with another. Not only will the new "personality module" provide additional or enhanced functionality, it will easily integrate into your existing system.
The compact and explosion-proof Millennium features a power disconnect switch to simplify maintenance, a scrolling LED display for calibration and configuration and meter jacks for easy current loop monitoring.The internal circuitry is equally well designed with performance enhancing proprietary circuits and firmware.
The best designers, technologies and components make Net Safety products responsive, precise, and reliable in the most extreme conditions.
We provide products at a competitive price, with superior functionality and demonstrated effectiveness.
A full range of gases and custom configurations are available (ppm ranges etc.). Please consult our Sales Department.
|
|
|
|
|
|
Fastest warning for explosion hazards
With bright alarm LEDs and a loud buzzer the transmitter CC28 (ATEX) warns of combustible gases. This avoids expenses for additional Ex-proof buzzers and Ex-proof alarm lights and their costly wiring.
The improved sensor technology and a special „chimney effect“ make the CC28 the catalytic combustion transmitter for combustible gases with the shortest response time worldwide. The proven delta alarm of GfG’s GMA controllers reduces the response time even further – a very important feature particularly for handling explosion dangers. This gives the user important seconds to take counter measures or to get to safety.
Adjustments are done directly at the transmitter by means of touch keys (one man calibration) without opening the casing. An optional remote control facilitates inspection, service and calibration considerably, e.g. if the transmitter is mounted close to the ceiling; you do not have to climb up a ladder.
The gas concentration can be read directly at the transmitter, at the remote control and at the controller. Alternatively you may decide for a low-cost model of the CC28 without display or alarm.
|
|
|
|
|
|
The Guardian range of infrared gas monitors offers near-analyser quality
continuous sampling, measurement and display of target gas concentrations at an attractive price.
The Guardian SP is a high accuracy monitor offering increased short term stability in lower ranges than Guardian plus models.
For many years, Edinburgh Sensors has pioneered novel non-dispersive infra-red dual wavelength sensors with a single optical path and without moving parts. This ensures long term stability, without the need for frequent re-calibration and makes the sensor highly gas specific and insensitive to other gases or water vapour.
The Guardian plus uses a robust infra-red source, proven in the Gascard II sensor, to ensure long lifetime and reduced susceptibility to shock. The reliability is further enhanced by the elimination of all moving parts from the sensor head.
The Guardian SP is easily maintained requiring only a few minutes per year to replace the hydrophobic particle filter in the inlet housing and a simple calibration procedure to check the accuracy, typically once a year. Applications include plant physiology, horticulture, fruit storage, leak detection, landfill, ventilation control, process control, furnace applications.
The Guardian SP includes an internal pump, liquid crystal display and temperature correction. It also offers a range of user-selectable bit-switches to control the latching alarms and analogue output options. The input power to the unit is user selectable to cover world-wide voltage and frequency standards.
|
|
|
|
|
|
Simtronics is pleased to announce the put on the market of the GD1, a new generation of open path detector.
The GD1 innovates by creating a new standard of toxic gas detection. At the heart of the detector is a tuneable laser diode that eliminates environmental effects from sun, rain, and fog. The laser scans single absorption lines where there is no interference from other gases. This new technology constitutes an important progress with exceptional performances and a extreme reduced maintenance.
Unlike traditional methods for detecting H2S (MOS or EC cell), the GD1 needs no recalibration and can replace multiple standard detectors to cover the same risk. Compared to traditional detectors the GD1 offers:
• Faster detection
• Reduced maintenance
• A life calibration
• Fast acting
The GD1 is also available with a dual output gas configuration, Methane and Hydrogen Sulphide.
Supplied with worldwide hazardous area approvals. Suitable for use in SIL 2 systems.
With its level of detection lower than 5ppm and it is faster response time (T90 < 5 sec) the GD1 is ideal to ensure the personnel safety on petrochemical installations onshore or offshore or for the sites of treatment of waster water.
Furthermore, the GD1 offers real cost savings, using a single transmitter / receiver pair, the detector covers distances of up to 100 metres. Installation and maintenance costs are reduced as fewer devices are needed to cover the same risk as several point detectors.
As with all Simtronics’ products, the GD1 is designed for early detection of hazardous events. It’s built to work safely in extreme areas and withstand the hardest environments onshore and offshore.
|
|
|
|
|
|
GfG's fixed gas detection systems are available as easy to operate single point units or as larger systems with several hundred transmitters. These multiple point systems consist of controllers and transmitters that communicate with each other. The transmitter changes the measured gas concentration to an electrical signal which is transfered to the controller. The controller shows the gas concentration in a display and immediately activates alarming devices in case of a gas leak. Advanced features such as data logging or online data transmission allow the user to easily monitor ambient changes in the environment. The Stand Alone unit is a combination of both transmitter and controller.
The transmitter's sensor is the "sense of smell" of a fixed gas detection system. The sensor is located in a metal sensor enclosure which is attached to the transmitter and converts the gas concentration into an electric signal. Electronics inside the transmitter changes this electrical signal for interference free transfer to the controller. The transmitter and the controller can be installed several 100 meters apart from each other.
|
|
|
The Model S4000CH Intelligent Sensor is a microprocessor- based transmitter designed for use with General Monitors' catalytic bead sensors. The unit features one person calibration and can virtually self-calibrate by simply activating a magnetic switch and applying gas. It is designed to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Complies with ANSI/ISA 12.13.01-2000 performance requirements for combustible gas detectors.
|
|
ToxiBoss is a wall mounted gas sensor with interchangeable sensing heads to cover a wide variety of toxic gas situations. It is approved intrinsically safe for hydrogen (Group B) environments. Its Class I, Div 1 and 2, Group BCD approval means that it may be used in any hazardous gas environment, except acetylene. And, being intrinsically safe, it can be serviced in place without having to disconnect power or to undertake a costly declassification of the area. Also, the ToxiBoss can be installed in Div 2 applications without the added cost of sealed conduit.
Pick any one of the following sensing heads to suit your particular needs.
Gas Range Units Sensor model Head Designation
CO 0-500 ppm TB-CO/500 TBH-CO/500
NO2 0-10 ppm TB-NO2/500 TBH-NO2/500
H2S 0-50 ppm TB-H2S/500 TBH-H2S/500
H2 0-25 ppm TB-H2/500 TBH-H2/500
Cl2 0-10 ppm TB-CL2/500 TBH-CL2/500
SO2 0-10 ppm TB-SO2/500 TBH-SO2/500
O2 0-100 % TB-O2/100 TBH-O2/100
|
|
Gas detectors E2606 are intended for air quality monitoring - control of combustible gas and oxygen concentration and prevention of gas leaks in confined spaces.
Depending on version the gas detector E2606 uses either advanced metal-oxide semiconductor or an electrochemical gas sensor. Concentration of combustible (methane, butane,hydrogen, etc) gases can be measured.
- Temperature range -20..+50 °C, <90 %RH
- Output relay 230V, 3A
- Supply 230 VAC or 24 VDC
- Diffusion, flow-through and remote sensor versions
- Visual and audible alarms, adjustable output relay
- Linearized analog output 4-20 mA
- RS485 Modbus RTU interface option for direct Fieldbus networking
- Wall-mount
|
|
The gas measuring systems for explosive gases and vapors made by J. Dittrich Elektronic determine the concentration of explosive gases and vapors in air in an ambient temperature from -10 to +50° C.
A pellistor or semiconductor sensor detects methane (CH4), hydrogen (H2), propane (C3H8), alcohol and benzine; additional hydrocarbons on request.
The calibration is carried out with the aid of the respective test gas by means of a potentiometer; however, a certain amount of cross-sensitivity of the sensor with regard to the other substances always remains.
Low-cost infrared measuring system for methane
Since the cross-sensitivity of the sensors gives rise to problems when monitoring methane, J. Dittrich Elektronic developed a new infrared measuring system which detects specifically methane quicker, more accurately and at less cost than conventional infrared systems.
|
|
|
|
|
|
myDatasens Mobile
Independent operation even at most unfavourable conditions enables an extremely cost effective and maintenance-free measurement network without compromises. The rugged and acid- and alkali-resistant instruments allows you to collect data for your application in a cost optimised way.
Application:
Portable measurement instrument for capture and transmission of gas concentration in air, to be used in:
Sewer systems
Industries
Public water and sewage systems
Product Characteristics:
Monitoring and alerting via Internet
ATEX-certified for zone 1
Automatic reconfiguration upon exchange of instruments
Measurement sites may be managed from anywhere around the world via the internet
Data storage on the instrument of up to 440.000 measurements
Adjustable measurement and transmission intervals
Real time clock synchronised with server
Extraordinary battery lifetime of up to 5 years - MicroPower® technology
Compact dimensions
Rugged IP66, IP67 and IP68 casing with high resistance against chemicals and with a protective rubber outer sleeve
Ultra low costs for start-up and operation
Download the sensor list on the website.
|
|
Crowcon manufacture detectors for flammable, toxic and oxygen gases to suit all applications. Our comprehensive range offers
* Compact and rugged designs
* High reliability
* Flexibility to adapt to specific use requirements
Our fixed gas detector product range:
Xgard Detectors for flammable, toxic and oxygen gases
Xsafe Safe area flammable gas detector
Flamgard Plus Flammable gas detector with display
TXgard Plus Toxic and oxygen gas detector with display
TXgard-IS+ Toxic and oxygen gas detector with display
Nimbus Infrared flammable gas detector
IREX (NEW!!) mV output, microprocessor controlled IR pellistor replacement
|
|
|
The Model S4000CH Intelligent Sensor is a microprocessor-based transmitter designed for use with General Monitors' catalytic bead sensors. The unit features one person calibration and can virtually self-calibrate by simply activating a magnetic switch and applying gas. It is designed to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Complies with ANSI/ISA 12.13.01-2000 performance requirements for combustible gas detectors. Options include 8 Amp relays, Dual Redundant Modbus and HART communication.
|
|
|
Utilising the latest technology MSA offers catalytic combustion, Point IR and Open Path IR detectors for continuous monitoring of combustible gases in hazardous areas.
|
|
The effectiveness of SIMTRONICS remote detectors (accuracy, fast response time and high reliability) guarantees the ultimate protection against the risks associated with gases in industrial environments.
The housings are given a special surface treatment to improve their resistance to corrosion (stainless steel or aluminium housings).
The measurement process is based on OXYCOL™ low temperature catalytic oxidation, enabling detection of all combustible gases and gives the detector an extremely long lifetime.
All the explosimeters are equipped with :
• An exclusive system of alarm verification in case of scale overrun,
• A linear response,
• A high stability,
• A very short response time.
The interchangeable and removable cartridges (as well as the support independent from the electronic box) make the remote detector easy to use and maintain.
All commands, configurations and readouts are remotely accessible using the infrared remote controller.
|
|
With the GD10P, the company has succeeded in establishing an international industry standard for gas detection.
The GD10P has been designed to be interchangeable with catalytic detectors using the existing cabling and a separate bridge interface.
Advantages of GD 10P
• No recalibration during its service life,
• 15 years warranty for IR source,
• 5 years full warranty,
• SimSource™ has an expected in-service life of 65 years,
• Very short response time , T90 < 5 secs,
• No false gas alarms.
The easy installation and operation of the GD10P contribute to its all-round solid economy.
The GD10P does not have any internal functions that require regular monitoring or maintenance.
|
|
The Model IR400 Infrared Point Detector is a hydrocarbon gas detector that continuously monitors combustible gases and vapors within the lower explosive limit (LEL) and provides alarm indication.
All electronics are contained within an explosion-proof housing so that the IR400's detector information can be processed locally. The IR400 operates with a 4-20mA signal, which is proportional to 0 to 100% LEL gas concentration at the detector. Configurations with analog output, Modbus and HART are available. Modbus and HART data can be used for predictive maintenance.
|
|
|
The Model IR5000 Open-Path Infrared Combustible Gas Monitor is designed for detection of hydrocarbon gases in the 0-5,000 ppm•meter and 0-5 LEL•meter ranges, simultaneously. The IR5000 uses a single beam source and detector to monitor gas concentrations, improving accuracy, reducing drift and improving immunity to false alarms.
|
|
|
|
|
|
Flamgard Plus is a Flameproof (Exd) flammable gas detector, which uses poison-resistant pellistors to detect explosive levels of hydrocarbons, hydrogen and other flammable gases and vapours, including aviation fuel and leaded petrol vapours.
Features:
Non-intrusive calibration
* Calibration can be performed locally without the need for hot work permits
* Local display and magnetic key enable calibration without opening the junction box
Flexible output options
* A 4-20mA signal is provided
* Optional alarm and fault relays are available to drive local alarm devices.
Rugged and reliable
* Constructed using highly durable marine-grade alloy with a tough polyester coating
* Ingress protection to IP65 as standard, IP66 with accessory
* Uses long-life poison resistant pellistors, which are resistant to halogens, silicones and lead.
Other toxic gas detectors in the Crowcon range include:
* Xgard - available in Ex d and i.s. versions
* TXgardIS+ - intrinsically safe toxic gas detector with display
|
|
Gas detectors E2606 are intended for air quality monitoring - control of toxic gas and oxygen concentration and prevention of gas leaks in confined spaces.
Depending on version the gas detector E2606 uses either advanced metal-oxide semiconductor or an electrochemical gas sensor. Concentration of toxic (carbon monoxide, VOC, freons, ammonia,H2S etc) gases or oxygen deficiency can be measured.
- Measuring range 0..5 %vol.
- Temperature range -20..+50 °C
- Output relay 230 VAC, 8A
- Supply 230 VAC or 24 VDC
- Diffusion, flow-through and remote sensor versions
- Visual and audible alarms, adjustable output relay
- Linearized analog output 4-20 mA
- RS485 Modbus RTU interface option for direct Fieldbus networking
- Wall-mount
|
|
|
The Model TS4000H Intelligent Toxic Gas Detector continuously monitors toxic gases in the ppm range or oxygen deficiency, delivering highly accurate detection and protection. The unit features one person calibration and can virtually self-calibrate by simply activating a magnetic switch and applying gas. It provides status indication and alarm outputs.
|
|
J. Dittrich Elektronic gas measuring systems for toxic gases and vapors determine the concentration of toxic gases and vapors in the air mixture at an ambient temperature of -10 to +50° C.
Specific electrochemical sensors measure ammonia (NH3), chlorine (Cl2), carbon monoxide (CO), oxygen (O2), hydrogen sulphide (H2S), nitrogen dioxide (NO2) and nitrogen monoxide (NO) in the ppm range.
The sensors are calibrated with the help of the respective test gas using a potentiometer; there is no or only negligible cross-sensitivity to other substances.
|
|
|
MSA offers a complete range of detectors that permanently monitor for dangerous levels of toxic gases to protect personnel and the environment.
|
|
|
|
|
|
MILLENNIUM II BASIC "SMART" GAS DETECTOR
Net Safety's next generation detector, the Millennium II BASIC is a robust, reliable, and low-cost safety solution delivering highly accurate detection and protection. Our state-of-the-art "SMART" (Self Monitoring Analysis and Reporting Technology) sensors provide a cost-effective detector solution that includes all the features you demand with complete ease-of-use and operation.
A full range of Combustible (Infrared & Catalytic Bead) and Toxic (Solid State & Electrochemical) sensors are available, all are completely interchangeable with the Millennium II and Millennium II BASIC transmitters.
* SMART Technology
* Low Cost Solution
* Market Leading Sensor Warranties
* Global Certifications - Class1 Div1 Explosion proof
* Analog, Relay, RS485 Modbus RTU, or HART communications available
* Low Power Consumption, Widest Input Power Range
* Infrared sensor technology utilizing a dual beam design with no "mirrors" that may become contaminated ("fogged up") or misaligned
* Non-intrusive, One Man Calibrations
* Visual LED Indication (full display available on Millennium II Dual Channel)
* Long Range (+2000ft.) Sensor Separation
|
|
Gas detection : O2, H2S, NH3, CO, NO, NO2, H2, SO2, Cl2, HCl, HCN…
The modern technologies used offer a high resistance to the humidity and temperature compensation as well as stability over time. In order to meet every requirement, SIMRAD Optronics ICARE proposes two different detection technologies :
• Electrochemical cells enabling a wide detection range and excellent selectivity.
• Semi-conductor cells providing extended detector lifetime.
The interchangeable and removable cartridge along with the wall mounting,
independent from the electronic housing, make this detector particularly simple to use.
• NH3 detection, low temperature
To meet needs of cold chains, a low temperature version enables detection down to -40°C.
|
|
The IGD MKIII flammable gas detector has been in service for many years gaining an enviable reputation for reliability and performance.
Developed originally for the off shore oil and gas industries using IGD's patented pellistor technology the MKIII today finds applications across many industries from drilling platfoms to boiler monitoring and everything in between.
Now ATEX approved the MKIII and available with a range of EEXd controllers, rack cards and 4-20mA output interfaces.
|
|
|
|
|
|
The FX-SMT Intelligent Single Gas Detection Transmitter is loaded with industry features. These transmitters come standard with non-intrusive calibration which eliminates the need to declassify hazardous areas, a user adjustable "calibration reminder" message. Smart sensor replacement assemblies available for plug in operation.
This single gas transmitter can be configured for the detection of combustibles, AsH3, B2H6, Cl2, Cl02, CO, F2, HCl, HCN, HF, H2S, NH3, NO, NO2, O2, O3, PH3, SiH4 or SO2.
Features:
- Non-intrusive calibration via a magnetic wand eliminates the need to declassify hazardous areas
- User adjustable "calibration reminder" message
- Pre-calibrated sensors for quick plug-in operation
- Using an optional adapter, oxygen and toxic gas detectors can be mounted up to 25 ft. away from the transmitter; 200 ft. for combustible gases (no adapter required)
- Connect to Thermo Scientifics (formerly GasTech's) controllers, PLC (Programmable Logic Controllers) or DCS (Distributive Control System)
- Industry standard, 4 to 20 mA output
- Housed in a NEMA 4X, copper-free aluminum enclosure (weather & explosion-proof)
- User friendly - simple to operate
- Economical
|
|
ARELCO’s Model ANATEX gas Analyzer is a microprocessor-based instrument for measuring oxygen (ppm or % level), Hydrogen in nitrogen, air… This instrument is designed in an explosion proof enclosure (MP Technology) for ATEX area (Zone1).
Simple menu choices, externally accessible by a capacitive pod, and LCD displays make set-up operation clear and quick. ANATEX is on auto-ranging analyser, with an excellent linearity. It uses reliable sensors like electrochemical cell or paramagnetic by ARELCO fits a large range of application and it can be used even in hydrocarbons, acid gases, pure gases… or for natural gas industries.
ANATEX can be also a TCD analyzer outputs to measure a blending gas like hydrogen in nitrogen or other specific gas blending.
|
|
Dräger's product range covers a wide variety of types: catalytic bead or infra-red IR sensor technology point or open path detection increased safety, intrinsically safe or explosion proof analog 4 to 20 mA, digital HART or RS 485 signal output with or without local display with or without on-board relays low budget or high end equipment Your local representative will gladly help you determine the right product for your application
Based on patented innovations, the Dräger PIR 7000 combines maximum light-efficient optics with a signal-stabilizing 4 beam technology. The double-compensating construction is characterized by the greatest possible robustness towards interferences (e.g. dust and dirt deposits). Due to its non-imaging nature, the measuring signal of the Dräger PIR 7000 remains unaffected by a partially covered beam. It can thus be ensured that the instrument fully complies with the requirement "no false alarms" .
|
|
The IGD MKIII flammable gas detector has been in service for many years gaining an enviable reputation for reliability and performance.
Developed originally for the off shore oil and gas industries using IGD's patented pellistor technology the MKIII today finds applications across many industries from drilling platfoms to boiler monitoring and everything in between.
Now ATEX approved the MKIII and available with a range of EEXd controllers, rack cards and 4-20mA output interfaces.
|
|
|
Biosystems, LLC, a Bacou-Dalloz® Company, is a leading supplier of gas detectors, respiratory maintenance equipment and monitoring systems, worldwide. Founded in 1981, Biosystems is headquartered in Middletown, Connecticut.
|
|
|
|
