Multi-channel amplifiers

Voltage: 0 V - 10 V
Frequency: 1 kHz

... measuring amplifier. With its high degree of protection (IP67) its singlechannel version can be integrated into the application even in the tough environment outside the switch gear cabinet. In the multichannel ...

The 508-SW is a smart multi-channel displacement, gap and bore measurement amplifier at about half the cost of the current amplifier. This new Capteura® multiple ...

Voltage: 5 V
Current: 250 mA
Power: 1 W

The 516-SW is a smart multi-channel displacement, gap and bore measurement amplifier at about half the cost of the current dedicated amplifiers. This new Capteura® multiple ...

Frequency: 2 MHz

... gauge bridge amplifier is a differential high speed front-end amplifier with high precision. Strain gauges can be connected to the measuring bridge in full bridges, half bridges or ¼ bridge construction. ...

Voltage: -10 V - 10 V
Current: 0 mA - 2 mA
Frequency: 0 kHz - 200 kHz

... VAC or 11 ...36 VDC • PE or combined PE-IEPE inputs • Cable adapter option: Fischer 9-pole neg. to BNC pos. (3, 4, 6 or 8 channels) Electrical properties Output signal type Voltage Input type Charge (Piezoelectric, ...

Voltage: 4,500, -4,500 mV
Frequency: 10 kHz

... compact 3-channel universal charge amplifier. Packaged in a welded stainless steel housing, it meets the highest requirements and can be used in various applications such as towing tanks, ...

Power: 5 W

... set up. CV9-C: 9 channel charge amplifier with individually selectable gain (x1, x10, x100) per channel via a three way switch. CV9-CL: 9 channel charge amplifier ...

Voltage: 24, 230, 115 V

Multiplex amplifiers for close sensor mounting without crosstalk. High range, high power and dust resistance. Automatic gain setting on IMX-A models for guaranteed high sensitivity. IMX-A series: 2 and 8 channel ...

Voltage: 24 V

The ICL series contains low-cost multiplexed amplifiers with 2, 6 and 8 channels. Manual and automatic settings are both available for reliable operation, independent from dust, misalignment and aging. The ...

Voltage: 5 V

Voltage: 85 V - 265 V
Frequency: 10 Hz - 5,000 Hz

... using the DC model. Multiple racks may be synchronized together for multichannel operation on a common surface to avoid inter-channel interference. About Modular Capacitance Rack System The ...

Voltage: -30 V - 130 V
Current: 40 mA - 140 mA

For Three Channels, E-500 Piezo Controller System • Plug-in module for E-500 piezo system • Position control (optional) • Interface / display modules (optional)

Voltage: 30 V
Current: 7 A
Power: 650, 750 W

6+ Channel Shimming Amplifier for MRI systems Product features -Best in class price / performance -Drop in replacement / custom interfacing -6 channels / ±30V / ±7ADC ...

Voltage: 3.3 V

... Amplet Booster provides up to 20 dBm of output power in an ultra-compact footprint and can be customized for single channel or multi-channel wideband power amplification. Standard ...

EDFA Amplifier Flexible options such as Optical Booster, Preamplifier or In-line Amplifier Output power up to 23 dBm Data rate and protocol independent Amplifies multiple wavelengths ...

2-Channel Charge Amplifier The UV-16 is a 2-channel charge amplifier that is compatible with the input of piezoelectric accelerometers and accelerometers with built-in ...

Voltage: 230 V
Power: 240, 120 W
Frequency: 80 Hz - 16,000 Hz

... require multi-channel high-power digital power amplifiers. Feature: * 120W/240W constant impedance and voltage high performance digital power amplifier (4-16Ω/100V) ...

Voltage: 5 V
Current: 5 mA
Frequency: 100 kHz - 10,000 kHz

... Channels Three, each with four outputs Mode: Independent Each channel independently driven Common A/B B/C outputs driven by A or B input Selection Internal push-on jumpers Output ...

Voltage: 5 V
Frequency: 50 Hz

Multi-channel signal conditioner for temperature monitoring in MR environment About the TempSens Fiber Optic Amplifiers Multi-channel signal conditioner ...

Voltage: 10 V - 30 V

The Photoelectric Amplifier Bus (PAB) series has a total of 3-channel photoelectric amplifier. These amplifiers are used in conjunction with Telco remote transmitter ...

Voltage: 500 V

... needing galvanic isolated amplifiers. All types of measuring with universal acquisition card: temperature, distortion, pressure, force, acceleration, displacement… DESCRIPTION E325 is a very flexible ...

Voltage: 0.5 V - 10 V
Frequency: 1 Hz - 10,000 Hz

... Conditioning and amplifier’s low-level signals to high-level outputs for multiple channels can be simultaneously and dynamically recorded and displayed on external devices. Features ● ...

... conditioning unit that is used to measure amplifier multichannel. This device is equipped with a field bus Profibus and a CANopen that provides 4 up to 8 sensors. Additionally, this device has a direct gain setting, channel ...

... According to individual customized specification - Plug-in terminal blocks Manifold configuration options as: - Multi-channel amplifier - Amplifier with the possibility ...

Voltage: 12 V - 36 V
Current: 200 mA
Frequency: 1,500, 800, 1,000, 2,700 Hz

... Display with graphic capability for easy set-up Precise detection of small parts Available as 2, 4, 6 or 8-channel versions Operation with inexpensive acrylic fibre optics

Current: 1,400 mA

The linear amplifier LA24 is designed to drive inductive loads like magnetic actuators with extremely low noise. LA24-x is a low power amplifier implemented in a 19' board and can have up to 3 channels. ...

Voltage: 5 V - 20 V

... in the automotive, tyre, wind power or rail industry – the MCMpro strain-gauge amplifier accelerates the development processes and simplifies the application wherever multi-axis tests are required. The ...