|
|
| The combination of these technologies produces a continuous on-demand supply of pure nitrogen. Typical applications include nebulizer gases, curtain gases, source gases, chemical and solvent evaporation, instrument purge and supply, evaporative light scattering detector use and sparging. |
|
Dimensioning range from 26 Nm³/h up to 320 Nm³/h at purity
up to 99.5 %.
Due to the development of special fibres filtrating compressed
air very efficiently, this plant achieves unchanging purity grades.
The IMT-MN is a cost-saving alternative to the traditional supply
by gas-bundles or tank installations.
As an option these plants are available in stainless steel or ATEX
dessign. |
|
A complete range of membrane module sets offers you the possibility to integrate your own nitrogen source. Your requirements can always be met thanks to the different sizes and membrane performance available.
The smallest module only measures around 30 centimetres in length and the largest around 1.5 metres. Due to the different measurements there is surely a module that will fit the equipment you are designing. |
|
‘Plug and Play’ Nitrogen Generator for LC/MS
The Parker Balston® NitroFlow Lab is a self contained generator that produces up to 32 lpm of pure LC/MS grade nitrogen at pressures up to 8 bar. It produces nitrogen by utilizing a combination of compressors, filtration, and membrane separation technologies. High and low pressure compressors carefully matched to hollow fibre membranes separate the clean air into a concentrated nitrogen stream.
The combination of these technologies produces a continuous on-demand supply of pure nitrogen. Typical applications include LC/MS/MS nebulizer gases for APCI and ESI, ELSD, Turbo Vaps and chemical solvent evaporation. The NitroFlow Lab has been tried and tested by all the major LC/MS manufactures.
The unique combination of the dual compressor generator ensures that the NitroFlow Lab has several unique technical advantages over all other existing LC/MS Nitrogen Generators.
Nitrogen is produced at low pressure and then compressed to 8 bar. This ensures minimal maintenance of the system with no compressed air filter replacements or condensate. The compressor life is guaranteed under the Parker Balston warranty for 8000 continuous running hours, the longest currently available on the market.
Parker Balston is the worldwide leader in separation and filtration technologies, and offers a broad range of analytical gas generators to meet your specific analytical instrument requirements. All products are backed by a fully staffed field sales and service organization.
|
|
Performance: max. 900 ltrs./h
Purity: max. 95 %
Supply pressure: 10 bar
Car tyres: max. 8 pces./h
Dimensions: 900x650x120cm (HxWxD)
Weight: 20 kg
- Industrial filters ensure adequate filtration of compressed air
- minimal compressed air consumption
- Installation operative after connection to compressed air! |
|
Parker has developed a nitrogen generation tyre compression unit, which have been specially designed for delivering high quality compressed nitrogen into tyres. Called TyreSaver and Truck TyreSaver the new range offers unsurpassed levels of service life and potential savings of $100'000 on tyre maintenance and downtime in a one year period. This means, a truck tyre inflated with nitrogen could easily go an extra 50'000 miles before the tyres need servicing.
The units are designed for filling tyres with nitrogen supplying the purity required to keep the tyres at constant pressure. Equipped for connection to an external nitrogen storage vessel or directly to the airline, the generator will automatically switch on and off depending on the nitrogen demand.
The compressed air can be sourced either from a central system, or from a dedicated compressor. High quality compressed air filtration, coarse, fine and carbon filters protect the membranes ensuring long membrane life.
Nitrogen in tyres is a concept which has been adopted by road haulage firms in the United States and Canada, who have been using Truck TyreSaver for the last three years. Moreover the concept is widely used in the Motorsport industry and NASA for a number of years, one factor behind this is Nitrogen's low risk of combustion. |
|
Parker Balston® SOURCE LCMS-5000 Series is now available for Applied BioSystems MDS Sciex API-LC/MS users
The Parker Balston® SOURCE-LCMS-5000 is a visually integrated and functionally modular LC/MS gas generation system which produces high purity nitrogen, zero air and exhaust pump gases for all Applied Biosystems – MDS Sciex LC/MS/MS instruments.
It produces nitrogen, zero air and pump exhaust air by utilizing a combination of a compressor with filtration, catalysts and membrane separation technologies. An integrated low-maintenance compressed air supply is filtered by high efficiency coalescing filters removing all contaminants down to 0.01 micron. Hollow fiber membranes subsequently divide the clean air into a concentrated nitrogen stream. The zero air is produced by catalytic oxidation which converts the hydrocarbons. A passive hollow-fiber dehydration membrane is used to create the exhaust pump gas.
The integrated Scroll compressor is ‘whisper’ quite at only 48 dBA and is supplied as standard with a 10,000 hour / 3 year warranty. Low maintenance and reliable this offers the best compressor warranty currently available on the market.
Parker Balston is the worldwide leader in separation and filtration technologies, and offers a broad range of analytical gas generators to meet your specific analytical instrument requirements. All products are backed by a fully staffed field sales and service organization.
|
|
Claind’s nitrogen generators satisfy all laboratory analysis and industrial process needs with very few exceptions.
The range includes compact generators with built-in oil-free compressors, medium and high pressure generators for industrial applications, and special generators for OEM applications.
Claind’s nitrogen generators are based on PSA (Pressure Swing Adsorption) technology for maximum reliability and gas quality. Claind has also patented the Fast Purity system, the most significant innovation in the world of PSA technology in recent years. |
|
The N110DR has been designed specifically to supply Nitrogen to all LC/MS, offering Nitrogen Gas in flow rates and purities suitable for these applications and comes set at recommended pressures.
This highly sophisticated NitroGen features dual redundant air compressors, resulting in uninterrupted supply of gas and therefore 100% LC/MS uptime even if one of the compressors failed. New robust design and the use of quality components further lengthen the lifetime of the compressors with even less maintenance requirements.
The intelligent PLC offers integrated self diagnostics which will alert the user if a fault or leak has been detected, service is required and aid remote fault finding resulting in further minimizing downtime.
The high design standards make this not only the most sophisticated gas generator on the market, but also the most reliable and intelligent solution for your LC/MS gas requirements. |
|
Nitrosource
autonomous 100%, with a reduced maintenance, the Nitrogen generators Parker replace the bottles of gas and the liquid supply of nitrogen.
Applications: inertage, network of nitrogen, packaging of food products...
Based on membrane technology, Nitrosource is the nitrogen generator of evolutionary design, enabling you to extend the capacity of the generator on site without repurchasing a complete generator. It thus follows the evolution of the growth of your factory. It produces nitrogen in full safety 24:00 /24H, until 4000 Nm3/h.
Nitrosource® enables you to easily produce nitrogen on site starting from compressed air.
Nitrosource® is composed of a central processing unit which can be wide in term of capacity by the addition of 5 pennies units. Thanks to the design Master/slave, up to 11 central processing units and theirs under units can be connected between them and managed like a single generator.
Nitrosource integrates a station of filtration of compressed air of high-quality. This characteristic optimizes laquality of compressed air in entry of the generator, ensuring a great longevity of the hollow fiber membranes. The generator is equipped with a digital system of data management to record and communicate the parameters of operation such as the pressure, the flow and the residual concentration out of oxygen.
The equipment is deprived of parts moving, ensuring an operation without concern, durable and
almost without maintenance. The generator is ready to function as soon as the compressed air is connected.
Nitrosource offers an unlimited quantity of nitrogen to you and can be easily connected to an external reservoir of storage. This will enable you to absorb the peaks of consumption in your applications where the demand for nitrogen is variable.
Ideal solution to replace the nitrogen bottles or the liquid nitrogen supply.
|
|
Nitroflow BASIC
autonomous 100%, with a reduced maintenance, Generators Parker the nitrogen replace the gas bottles and the liquid nitrogen supply.
Applications: inertage, network of nitrogen, packaging of foodstuffs...
Based on membrane technology, Nitroflow BASIC is the nitrogen generator with the most compact, esthetic integrated compressor and silencer of the market (<55 dBa). it produces nitrogen in any safety 24:00 /24H, until 1,5 Nm3/h.
It integrates a piloting by microprocessor, a control and adjustment of the parameters of work on touch screen and an analyzer of O2 to visualize the nitrogen purity. The strong point of the system: the compressors have one lifespan longer than those of our competitors (patented exclusive system). 2 years or 8000 operating hours exclusive guarantee.
Ideal solution to replace a nitrogen bottle/day. |
|
ADVANTAGES AND ECONOMIES
Conceived specifically to meet the requirements of flows and purities of the analytical instruments
Increase in the analytical performances
Increase in the effectiveness of the laboratory
Reinforced safety
More important economies
Simple installation
Recommended and approved by the manufacturers of instrumentations LCMS
APPLICATION
Product of nitrogen high purity starting from compressed air.
Replace the nitrogen bottles for the following applications:
- LCMS/MS
- DETECTOR ELSD
- EVAPORATION Of SAMPLES
Principle of operation
Nitrogen is produced by using membrane technology, starting from a network of compressed air without oil or pre treaty of a mini pressure. of 110 psi.
The fall of pressure is only of 10 psi (0.5 bar), weakest of the market, making easier the connection of the generator to your own network of compressed air.
The diaphragm functions on the principle of the selective permeation, or the oxygen, the steam and the CO2 which are fast gases cross the diaphragm, while nitrogen, gas slow, continuous to circulate in the form of gas flow inside the diaphragm. |
|
Nitrogen generation plants designed for multiple industrial applications.
These plants, both standard and industry design are manufactured for capacity ranging from 50 Nm³/h up to 5.000 Nm³/h and ensure large
and continuous volumetric flow rates.
Following options are available:
redundant design, back-up system, operation-hous counter, alert function, booster, stailess steel or ATEX design, container installation mounted. |
|
Membrane technology in the range of nitrogen purity
of up to 99,9 %.
This generator type provides easy handling without specific
training resp. comprehensive operation manual.
When nitrogen consumption is stopped, the unit
automatically switches to stand-by mode.
Maintenance is indeed negligible, just the filter set
needs to be replaced.
Connection and start-up are actually very easy,
just by use of a standard 230V outlet, at rating of
1,5 kW up to 6 kW, depending on the production
capacity.
This model range HN provides N2 purity grades from
98,0 % up to 99,9 %, at capacity from 2,9 Nm³/h up to
103,0 Nm³/h, depending on the required purity grade. |
|
Perfected nitrogen technology for permanent operation.
N2 purity up to 99,5 % using the reliable membrane technology.
Dimensioning range of this generator model line is from
0,10 Nm³/h up to 15,00 Nm³/h.
Advantages for the user:
- constant high quality of N2
- continous nitrogen availability at anytime
- low installation costs
- negligible running costs
- safe and easy operation
- no handling costs as for cylinders or gas bundles
- no handling safety hazard as for cylinders.
Following options are available:
ATEX, stainless steel version, analyser unit. |
|
Atlas Copco proposes a range of 7 nitrogen generators NG offering of the nitrogen flows from 1,3 to 130 m3/h and of the rates of purity up to 99,99%.
Based on technology PSA, the principle of operation is simple and powerful. Easy to install, the NG are compact and reliable. Their modular concept makes it possible to assemble several units in parallel to adapt the production of nitrogen at the request of the process with an optimal energy efficiency. Used downstream from compressors of air and equipment of treatment of air Copco Atlas, they offer all the advantages of a comprehensive solution: quality of the components, traceability, optimal energy efficiency, services. |
|
ADVANTAGES AND ECONOMIES:
- Conceived specifically to meet the requirements of flows and purities of the analytical instruments
- Increase in the analytical performances
- Increase in the effectiveness of the laboratory
- Reinforced Safety
- More important Economies
- Simple Installation
- Recommended by Manufacturers of Instrumentation
APPLICATION:
- Produced nitrogen high purity starting from compressed air.
- Replaces the nitrogen bottles for the following applications:
- GC-Gas Vector
- GC-FID, NPD, ECD, AED
- ICP
- ELSD
- FAKE
- LCMS
- Food of a complete laboratory to supply several analytical instruments (LCMS, ICP, EVAPORATIONS Of SAMPLES)
Principle of operation of the PSA:
Technology used to produce a nitrogen flow high purity is adsorption with swinging of pressure. This technique uses a molecular bed of sieve with coal (CMS) to selectively eliminate O2 and the other contaminants from the ambient air. Alternate bed between the modes of purification and regeneration to ensure a continuous production of nitrogen.
The gas generator is designed to receive filtered pre compressed air with 7 barg provided by a compressor without oil (provided by the laboratory or integrated in the generator). This flow of filtered and compressed air passes then in the bed of CMS which is in mode of purification. At this point in time O2, CO2, moisture and certain hydrocarbons are eliminated from the compressed air, producing a gas flow nitrogenizes clean, dry and of high purity. |
|
Nitrogen generation up to 99,9999 / 6.0 purity with "Pressure Swing Adsorption".
The technology of Pressure Swing Adsorption provides for nitrogen provisioning at purity grades of up to 99,9999 % and capacities
ranging from 0,5 - 2.000 Nm³/h.
Following options are available amongst others:
- pressure booster up to 300 bar
- flow meter
- special voltage design
- pressure dew point indicator
- remote inquiry.
All units of the PN model range are equipped with touch panel
and USB port. |
|
Claind’s nitrogen generators satisfy all laboratory analysis and industrial process needs with very few exceptions.
The range includes compact generators with built-in oil-free compressors, medium and high pressure generators for industrial applications, and special generators for OEM applications.
Claind’s nitrogen generators are based on PSA (Pressure Swing Adsorption) technology for maximum reliability and gas quality. Claind has also patented the Fast Purity system, the most significant innovation in the world of PSA technology in recent years. |
|
The domnick hunter MAXIGAS range of nitrogen generators has been developed to allow users to produce their own supply of nitrogen gas on-site, without the need for traditional high pressure cylinder or liquefied gas supply.
A domnick hunter Maxigas nitrogen generator can very easily form the basis of a complete central nitrogen supply, furnishing multiple analytical instruments with clean, dry nitrogen.
The MAXIGAS generators produce nitrogen gas from a virtually free resource %u2013 air. Designed to operate from compressed air, the generators deliver a continuous, uninterrupted supply of nitrogen gas at purity from 97%-99.999%.
The MAXIGAS systems offer the safest, most convenient and economic source of nitrogen available. The compact, modular design allows easy upgrading of the system as production capacity expands.
At 10 ppm oxygen content flow rates vary from 1.3 Nm3/hr to 6.5 Nm3/hr. At 1% the corresponding flow rates available are 11.8 Nm3/hr %u2013 59.1 Nm3/hr.
|
|
KOFLOC Nitrogen Gas Generator MNT SERIES (2.5NL/min-20NL/min)
KOFLOC Nitrogen Gas Generator MNT SERIES is a small, low-cost nitrogen generator with a small compressor, allowing it to be used anywhere with just a 100 VAC power supply. The adsorbent (molecular sieving carbon selectively adsorb a large amounts of oxygen under high-pressure condition, quickly removing oxygen carbon dioxide and moisture out of air, leaving only the high purity nitrogen gas as the final product. The adsorbent material releases oxygen when depressurized. High-purity nitrogen gas can be produced continuously by PSA (pressure swing absorption), which is a method of alternately pressurizing 2 adsorption vessels.
FEATURES
♦ Fully automatic
♦ Compact
♦ 100 VAC power supply
♦ High-purity and dry (–55˚C or less) nitrogen gas can be obtained
♦ Aluminum pressure vessels
♦ Quiet operation
♦ Quick startup
♦ High purity (99.999%) is also available
APPLICATIONS
* Substitution for nitrogen gas cylinders
* For heat treatment processes
* Semiconductor processes
* CA storage gas for fruits and vegetables
* Non-oxidization seal gas
* Explosion-proof or rust-prevention gas
* Seal gas for shipping
* Blanket gas for synthetic fibers and melted spinning |
|
The NM20Z is a self contained Gas Station designed specifically for the API Analyser Range. It is a plug and play system, fully tried and tested. You will be operational in minutes and running analysis without interruption.
Features & Benefits
Three gas lines from one system
No more cylinders, regulators, re-ordering or safety issues
Quiet operation
Simple to install to any analyzer
No electrical requirements
Wall mountable
24 hour operation |
|
The LASERGAS nitrogen generator is a truly high range generator thanks to sophisticated technology and exceptional performance.
This unique gas generator is capable of producing nitrogen at very high pressure. It is available in various versions with different outputs, purity and pressure ratings.
The LASERGAS nitrogen generator can be used in any area of industry requiring a medium or high pressure nitrogen supply, or whenever intermittent demand requires large reserves of nitrogen to be kept ready for rapid consumption. |
|
| ... products without technical information |
| |
|
|
see the results for the following category