|
|
High Pressure Filters-Worldline 100 up to 21.1 gpm, up to 6525 psi, In-line mounting, HD 049/HD 069
Application
In the high pressure circuits of hydraulic systems.
Performance features
Protection
against wear: By means of filter elements that, in full-flow filtration,
meet even the highest demands regarding cleanliness
classes. Protection against malfunction: Through installation near to the control valves or other
expensive components. The specific determined flow rate
guarantees a closed by-pass valve even at < 930 SUS
(cold start condition).
Filter elements
Flow direction from outside to center. The star-shaped pleating of the filter
material results in:
- large filter surfaces
- low pressure drop
- high dirt-holding capacities
- long service life
|
|
BELL In-line Filters grant a high protection to the most delicate components of an oleodinamic system. Placed in the site under pressure, they keep the particles sucked or produced by the pump up to a size of 10 micron.
These filters are normally applied in addition to the standard filters in suction or release, as a last barrier of protection before the entrance in directional valves, flow regulating valves and all those components which require a high grade of absolute filtering.
The body is made in a treated aluminium alloy to obtain a minimum dimension and weight.
The filtering element, instead, is made in synthered bronze with a conic shape to resist to high pressure without collapsing.
|
|
High Pressure Single Strainer - Simplex T Type
The Simplex T Type extends the range of S type filters to higher pressures, suitable for both liquid and gas applications and available with bolted or quick release type covers.
Standard Features
Quick release covers eliminate the need for tools for maintenance.
Designed for pressure ratings up to ANSI class 300lb (900 PSIG).
Flow is from inside to outside the basket to trap and retain debris.
High basket area to pipeline CSA ratio of over 10:1 in most cases.
Can be fitted with coarse perforated baskets (2mm as standard) or fine stainless steel mesh inserts to give particle removal down to 50 microns.
Disposable depth type cartridges are available for filtration to 5~10 micron for liquid and 1~2 micron on gases.
|
|
98 Series Filters - High Pressure (10 micron)
98-1110 Series T-Type Filter:
Designed for high flow applications
Features cleanable element
Available options: electrical, visual, bypass valve, visual pressure differential indicator, bypass relief valve, electrical bypass
|
|
|
The pressure line filter is an essential part in most hydraulic systems. When the hydraulic components are sophisticated, with close tolerances and a regulation function (not simply that of control) the use of filters in the pressure lines is a must.
|
|
Ikron %u201CFluid Filtration%u201D from Casappa %u201CFluid Power Design%u201D
An accurate filtration expands the life of all components and improves the overall efficiency of your hydraulic system.
Suction filters
Return filters
In line filters spin-on type
In line medium and high pressure filters
Accessories
|
|
Pressure Filters SF
STAUFF pressure filters are designed for the most demanding applications. They come in a variety of sizes, configurations and with numerous porting options.
* operating pressure to 420 bar
* flows to 1320 l/min
* BSP, NPT, SAE o-ring ports
or SAE flange (codes 61/62)
* filter head made of spheroidal graphite cast iron,
filter bowl made of cold drawn steel
* wide range of valve options
* various element types and media available
* standard bowls or top-loading bowls available
* visual, electrical and visual-electrical indicators
|
|
High Pressure Mini Tee-Type 4100 Series Filter
The 4100 series is a compact , lightweight tee-type filter that provides reliable and economical protection for critical testing equipment, valves, gauges and instrumentation. Designed with high dirt holding capacity pleated elements.
Elements
- No media migration due to the use of 304 stainless steel microweave wire mesh.
- Stainless Steel microweave mesh 9 micron ratings from 10 to 300 micron.
- Stainless Steel Sintered .5, 1, 3 and 7 micron absolute.
- Random Metal Fiber (metal fiber felt) available in 3, 5, 10, 25, 40 & 75 micron.
- Microglass ratings 3, 5 and 10 micron absolute
|
|
|
Our High Pressure series filters are designed for pressure line applications where design flexibility is required. Besides the standard T-Type and/or L-Type porting, we offer manifold type filters to provide compact and direct mount installation. This series is rated for flow from 50 to 150 gpm and a working pressure range from 4500 psi to 6000 psi.
|
|
Applications
Filtration lubricating oils and hydraulic fluids in engines and machines
Advantages
OEM quality
Proven technology
|
|
The 3000 series filter is used after the pump and/or as a return line filter in moderate pressure lube oil systems. This series is also ideal in hydraulic systems with return line pressures exceeding 250 psi.
Elements
- Multiple length elements
- Microglass beta 75 in 2, 5, 10 and 20 micron
- Stainless woven wire 141 micron
- Cellulose 3 and 10 micron
Features
- Housing material: anodized aluminum
- Flow: 0-150 gpm (100 SSU oil)
- Pressure: 800 psi maximum operating
- Temperatures: -65° to 250°F
- Port sizes: ¾” to 2” NPT or SAE
- Bypass settings: 25 and 50 psi
- Element cleanliness indicators: visual & electrical
- Easy cartridge element installation
|
|
|
Our Medium Pressure series filters are designed for continuous working pressures up to 4500 psi and flows from 20 gpm to 150 gpm. Many of the filters within this pressure range conform to the AIAG automotive HF2, HF3 and HF4 specification.
|
|
W322 duplex filters provide continuous, uninterrupted filtering of flows up to 50 gpm. The proprietary bowl check valves insure leak free maintenance during replacement element cycle. The high density aluminum material provides for a
compact and lightweight filter design. Five media grades are offered down to 5.1μ(c). WF elements core collapse options range from 150 to 3000 PSI.
The differential pressure indicator line is designed to work with the wide assortment of bypass valves. Thermal lockout and surge control are two key
features incorporated in many of the valves.
|
|
|
|
|
|
General description
HOFFMANN pressure filters cleanse coolants such as oils and emulsions of:
- metallic particles
- rubber
- plastics
- glass
The filtering capacity for each filter vessel lies between 150 and 200 l/min.
Soiled coolant is pumped into one, or several simultaneously operating pressure filter vessels. These vessels are equipped with nylon support filters and disposable paper filter bags. The soiled coolant penetrates these filter elements from the inside out, and the particles of impurities are trapped in the filter bag.
The so-called filter cake is formed as filtered impurities build up in the pressure filter vessel filter bag. This filter cake represents a high-performance filtering layer that enhances the filtering effect even more. When the filter cake reaches a defined size the throughput capacity of the filter declines and the filter must then be cleaned. Changeover of the facility to the standby pressure filter vessel is made when the signal for cleaning the soiled filter vessel is issued.
|
|
|
ServoSaver filters offer point-of-use filtration for some of the most sensitive hydraulic valves that there are, servo/proportional valves. Complete protection is provided by non-bypass filters equipped with high collapse strength elements installed directly at the valve. The ServoSaver is designed specifically for this use and is not an adaption of an in-line filter intended for bypass filtration.
|
|
|
|
|
|
MPD series filters are an outstanding choice for today's demanding hydraulic control and circulating oil systems. The MPD's innovative modular design, rugged ductile iron construction and coreless element technology, combined with many other features, provide solutions across a broad range of industrial applications.
The Modular design provides user flexibility for simplex or duplex applications. Incorporating side chambers as simplex filters along with duplex installations provide common elements across the circuit design.
Construction features like full ported transfer valve with neutral center flow capability offer tremendous benefit in cold start conditions. Standard features like pressure sensing taps, vents, drains and internal pressure equalization make this product incomparable in industry.
IL8 series filters are excellent choices for your demanding applications whether you require simplex, duplex or quadplex assemblies.
Wherever high flow or high capacity filters are required, the IL8 series can be applied with confidence. Filter housings have a simple yet critical job... securely contain the filter element with positive internal sealing.
The IL8 series filter housings are the result of careful engineering. High grade materials are used to provide strength at critical stress points.
The cover and base are annodized aluminum, the handle is nickel plated ductile iron and the bowl is rugged carbon steel. The result is a reliable high performance filter for an array of applications.
|
|
Simplex Type S
The general purpose standard, single basket filter with a quick-release cover for easy maintenance.
The design does not require specialised tools or knowledge, and results in a minimum of downtime.
Suitable for both liquid and gas applications.
Sizes: 1" to 12" bore, flanged to ANSI 125/250FF and 150/300 RF.
Can be drilled to BS tables and DIN standards.
Also available with screwed connections 1" and 1½" sizes.
Materials: Cast iron, cast steel and stainless steel, all fitted with cleanable baskets and inserts or disposable gas cartridges as required.
|
|
The 5000 series spin-on filter is commonly used to remove contaminates ingested or generated in hydraulic or lube oil applications.
Elements
- Microglass beta 75 in 1, 3, 6, 12 and 25 micron absolute
- Stainless woven wire 141 micron
- Cellulose 3, 10, 25 micron
- Water absorbing 3 and 10 micron
Features
- Housing material: Cast aluminum.
- Flow rates: 0-125 gpm
- Pressure: 250 psig.
- Temperatures: -65º to 250º F
- Port sizes: 1/2" to 1-1/2" NPT or SAE
- Bypass settings: 3, 5 ,15 and 25.
- Element cleanliness indicators: visual, electrical and gauge ports.
- Easy to install spin-on elements.
|
|
Five separate port options provide for maximum design flexibility in the W080 filter series. Quick filter change outs are accomplished with the use of our
serviceable bowl ring assembly. The size and material configuration are will suited for todays demanding proportional and servo applications. Our standard
bowl drain plug helps relieve system pressure during filter change outs. Western Filter’s proprietary BetaPoreTM 5 layer media is offered in a variety of
PakTM and meets the HF3 automotive standard. Three different media grades are offered down to 5.1μ(c). WF elements core collapse options range from 150 to 3000 PSI. The differential pressure indicator line is designed to work with the wide assortment of bypass valves. Thermal lockout and surge control are two
key features incorporated in many of the valves.
|
|
|
The designs offered in this filter series accommodate the need for a full range of port types and configurations. Working pressures range from 500 psi to 800 psi and are available with BetaPore or Coreless media.
|
|
|
BGTS return in-tank filters feature Parker's exclusive magnetic prefiltration core which collects ferromagnetic particles from fluid upstream of the filter element. This feature alone could save hundreds of dollars a year by protecting costly equipment from increased wear and malfunction by assuring that the fluid is as pure as possible when it leaves the filter. Even during bypass due to cold start up, contaminant is collected by the magnetic core, a feature of importance on any fluid power system.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
