... in order to reduce electrical stress. Splicing connectors for use in MV underground joints. Centred bore. Tapered edges. Tinned aluminium alloy body and aluminium alloy screws. Moisture block barrier in the center. ...
MECATRACTION
... General features ✔ These butt connectors enable the connection between an aluminium cable and a copper cable. ✔ Bimetal butt connectors, covered inside with neutral grease on the aluminium side, the ends closed by a protection cap. ✔ These butt ...
MECATRACTION
... Aluminium Junction Butt Connectors General features ✔ Equal sections. ✔ Aluminium junction butt connectors, covered inside with neutral grease on the aluminium side, the ends closed by a protection cap. ✔ These junction butt connectors are packaged ...
MECATRACTION
... Keyless shaft locking bushings easily attach hub components to shafts without the need for a keyway or key, while helping reduce wear on the mating components. They offer precise mounting and are ideal for rotational or axial load applications ...
ZERO-MAX
... Press Fit Slotted Locator Bushing Available for 3/16" through 1" diameter pins (6mm-25mm in metric sizes) Tool Steel, heat treaded to RC 58-62 Supplied with Roll Pin. Bore Bushing Hole for 0.0003/ 0.0005 press fit. ...
... Dimensions - d16-12 d400-355 Pressure rates - PN10, PN16 Connections - solvent spigot solvent socket Certificates - EURASEC Hygienic Certificate, GOST Certificate, Rostehnadzor Permission ...
Praher Plastics Austria GmbH
... Fitting with socket connection for the connection of VAG BAIO®plus System components and to shut off the spigot-end side of cast-iron-, PVC- and PE-HD pipes. Suitable for use in water distribution applications. Sealing system/standard: Fitting ...
... This rounded device is comprised entirely of nylon-6 which is also known as PA-6. It is black in color and can easily be snap-fitted into panels. Tools are not required in the simple procedure needed in order to install this device. Rough panel hole ...
Skiffy
... easily and quickly fitted re-usable (threaded version) good resistance to alkalis and acids good resistance to chemicals conforms to RoHS guideline REACH according to --> Technology / Technical Information / REACH TEMPERATURE RANGE -20°C to 70°C short ...
NORRES Schlauchtechnik GmbH
... For fine-stranded round conductors, e.g. to DIN EN 60228 Cl. 5 from 0.75-4 mm² For multi-stranded round conductors, e.g. to DIN EN 60228 Cl. 2 from 6–400 mm² For pre-rounded multi-stranded sector shaped conductors Simple cable entry due ...
Klauke
... Pressure grade: 0.8MPa～1.6MPa Specification and model: dn50mm ～dn1000mm Nominal pressure: the corresponding nominal pressure of electric-melt sleeve connection should conform to requirements in the table below. ...
... Cast iron sleeve NF 29323 flanged PN10/16 for ail common fluids of 2nd group. Installed with a butterfly valve, could replace a flanged gâte valve with the same length without modifications of the installation. Drain DN1/2" BSP. SPECIFICATIONS : • ...
SFERACO
... The BOxG series is a line of stainless steel bushing. The series includes eight models: BO8G, BO12G, BO15G, BO20G, BO25G, BO32G, BO40G, and BO50G. The models in the series range in sizes, with the smallest at a size of 0.25" and the largest ...
FG INOX
... - Whitworth pipe thread, thread M5 - Material stainless steel 1.4301/1.4307 - Temperature range -20 to +120˚C - Working pressure range -0.95 to 16 bar ...
... SP bushings are similar to P bushings, but with top serrations to prevent rotation in soft materials. SP bushings are recommended in high-torque situations for materials such as magnesium, aluminum, masonite, ...
CARR LANE MANUFACTURING CO.
... Used in construction, it is made only on the customer’s recommendation. It is possible to produce it in S355J2 or in 41CrS4, 32CrB4, B7, 42CrMo4, 25CrMo4, AISI 304, AISI 316. In the case of S355J2 steel, it is possible to supply products with the CE mark. The ...
... Single flange dismantling joint with pyramid gasket. Adjustable via tie rods, ideal for decoupling elements and compensating misalignments in rigid piping. Made of carbon steel with epoxy-polyester coating. The SBJP dismantling joint is a key technical ...
... Our insulating bushing provides protection for wire, cable tubing, and hose from sharp, uneven drilled or punched holes in sheet metal. It has been designed with multiple locks to positively snap in panels (without tools). Our bushing ...
ISC PLASTIC PARTS
... For use in automobiles with hybrid drives. To cover and protect electrical plug connections. Punched part made of highly ductile rustproof steel strip ...
... Connectivity standard Internal thread GAS cylindrical ISO 228/1. Operating pressure 10 bar at 20°C Max working temperature 80°C Colors Black (RAL 9011) ...
Bucchi S.r.l.
... Manufactured to the requirements of ASTM A-351 Basic dimensions and pressure ratings in accordance with ANSI B16.3/150lbs ...
DIXON GROUP EUROPE
... Rubber bushings have several applications, such as vehicle cabines, motors, etc. ...
... bronze self-lubricating bushing The standard bronze bushing offers operating ranges suitable for wide applications. BP25 self-lubricating bearings have a very good coefficient of friction, down to 0.01. The Metafram ...
... anilox sleeves – the right solution for all flexographic printing jobs Our anilox sleeves provide an enormous advantage, particularly when it comes to short printing jobs and frequent retooling. Our anilox sleeves can be installed in no time and deliver ...
INOMETA
the best suppliers