Conduction heaters

Power: 744 W
Temperature: 760 °C

... not only set the industry standard for cartridge heaters, it continues to make improvements in construction and design. Among these innovations is the 1/8-inch FIREROD. This miniature cartridge heater ...

Power: 5 W - 100 W
Temperature: 538, 760 °C

The FIREROD cartridge heater revolutionized the heating element industry in 1954 when it was patented as the first swaged cartridge heater. The mechanical procedure of swaging reduces ...

Temperature: 932 °C

The Watlow HT FIREROD cartridge heater is especially designed for high-temperature platen applications up to 1600°F (871°C). The HT FIREROD high temperature cartridge heater utilizes the same industry ...

Power: 450 W - 1,500 W

... of cartridge heaters (G2 with Thermostats; temperatures of 0 to 85°C) are screw-plug immersion devices that feature welded-in steel tubes with diametric measurements of Ø 36 mm. The devices sport switchable ...

Power: 100 W - 4,000 W

The Type HLP is a heavy duty cartridge heater developed by Herbst Beheizungs-Technik. It is specifically built with stainless steel cartridge construction suitable fro AC operation. In addition, the framework is available ...

Power: 100 W - 2,000 W

The Cartridge Heater is a heavy duty cartridge developed by Herbst Bezeizungs-Technik. It is specifically built suitable for AC application. In addition, the framework is available with stainless steel cartridge heater. ...

... Extruders. The Hotwatt Standard Band Heaters are manufactured in one or two piece constructions with maximum inside diameters of 11 1/2" and 22 1/2" respectively. Three or more sections are employed when heaters ...

Power: 10 W - 15,500 W

Hotwatt's Cartridge and Immersion Heaters are designed with a controlled work temperature of up to 1250°F, obtained through a combination of heater location and power wattage output. These devices ...

... the resistance wire into the sheath is accelerated by the cartridge heater from Superwatt. The relocation of the wire so that it is close to the sheath accomplishes this. The heater’s outside diameter ...

Power: 100 W - 3,150 W
Temperature: 350 °C

High load VULSTAR cartridges are especially suitable where space is at a minimum. Cartridges in AISI 321/ Din 1.4541 stainless steel. Filled with high-temperature (HT), non-watertight thermal cement. Supply voltage 230V 1 P. 2 flexible ...

Power: 100 W - 450 W
Temperature: 350 °C

Ideally suited for heat ing cy lind rical sha pes in damp env ironments, in the presenc e of fatty matter, molten plastic, rubber, etc.(350°C max imum). Prov ided with brass or stainless prof ile shielding, brazed connection cover and ...

NH-CBH Ceramic Band Heaters were developed to the maximum peake to meet your industrial requirements for high temperature long lasting heaters. Ceramic band heaters are widely used ...

National heaters Mica Strip Heaters are reliable way to provide uniform heat over a flat surface, efficient and economical, mica Strips feature thin construction and high quality insulation for effective ...

Power: 25 W - 1,600 W

Technical Data Types:DG: Brass DGS: Stainless steel Wall thickness:3,5 mm Operating temperature:DG: 280°C max* DGS: 350°C max* * Measured at the surface of the heated sidemax Dimensions:from diameter 24 mm, 16 mm length Load:DG: ...

Temperature: 700 °C

Conduction heating panels are designed and manufactured in large dimensions using either cast aluminum heater technology or mill groove heater assemblies with top and ...

- Max. watt density over the surface of the heater : 5 W/cm² - Max. operating temperature over the surface of the heater: 340°C, depending on working conditions. - Available in 2 versions: * ...

Strip heaters are used for heat transfer by conduction towards surfaces or by convection to heat liquids, air or gases. Strip heater sheaths are constructed in stainless steel. The heaters ...

Band heaters are elements with different diameters and heights, designed to heat and to maintain the temperature of cylindrical parts.Heat transfer is usely achieved by conduction or by radiation for ...

The Band Heater is manufactured by Chromalox, and is specifically designed to supply uniform heat transfer. This device is configured in a single or two-piece structure for easy installation and removal. It can work with ...

We supply high density cartridge heating elements that work as heaters to achieve working temperatures of 850°C and specific surface loads of 50 W/cm2 up to a metre long. Ultrawatt cartridge heaters ...

Cartridge heaters: ceramic-, metal-, high performance cartridge heaters Cartridge heater with highest power density in the smallest installation space. The cartridges are smoothed on ...

Power: 300 W - 4,500 W

The Caloritech™ BC Band Heater is an aluminized steel strip heater formed to a semicircle. A spring at the terminal end keeps the heater halves in contact with the barrel and compensates ...

... ceramic insulated heaters can be tested and worked without mounting into systems. If you mount these heaters in order to provide heat transfer, these heaters will be long termed because ...

MIKAPLAST heaters are heater bands with micanite insulation that are employed in the heating of the plastification cylinders of the plastic moulding machines. They can be used when the ...

... armored mica band heaters are capable of generating a maximum capacity of 4 Watts/cm². They are specially designed for the plasticfication of cylinders as well as extruders. These band heaters are ...

Power: 1,500 W - 12,000 W

Heating elements of stainless steel (AISI 304) for heating in containers or vessels where the liquid is not water. Is often applied within food industry, where the requirements to hygiene are high.

Cartridge heaters manufactured by EP are constructed without thermocouples. They are available in various versions namely the low, medium and high power density types. The high power density kind is integrated with a ...

Since 1969, date of its foundation, Crei has started with the production of cartridge heaters. At the very beginning the LD series, low power density cartridge heaters, have been designed and developed ...

... of electric heating elements; they make it possible to use high watt loads in small spaces, thus ensuring excellent reliability in heavy-duty work conditions. Their special construction technology makes them the most ...

Power: 50 W - 3,500 W

The CIR-3014 series of cartridge heaters from OMEGA provides high quality services in a sturdy casing. Models that require 120 or 240 V of power are available. They also offer shock and vibration resistant operations. ...

Power: 400 W - 3,000 W

... Band Heaters HB Series is engineered with two OMEGALUX® PT series 240V mineral insulated strip heaters with chrome steel sheath that provide quality output. With a capacity to withstand Sheath ...

The heater will keep temperature of iron tips during operation. Achieving resilient and high power unit at the same time. Ideal for components that require large heat capacity. This is a dedicated heater, ...