Binder electric ovens

... and operated by a gear motor. The unit is equipped with an integral torque regulator. Efficient heating is provided by an electric heat exchanger, positioned on the side panel of the drying unit. The heat exchanger is ...

Maximum temperature: 500 °C - 1,000 °C
Capacity: 8, 90 l
Width: 1,600 mm

... in the furnace chamber to prevent dangerous conditions for the furnace or personnel Defined application within the constraints of the operating instructions NTLog Basic for Nabertherm controller: recording ...

Maximum temperature: 950 °C
Capacity: 1,570 l - 3,790 l
Width: 1,780 mm - 3,080 mm

... can be used while working in gloves Handles on the left and right side of the hood for opening and closing the furnace Hood safety switch Solid state relays provide for low-noise operation Type K ...

Maximum temperature: 900 °C
Width: 2,200 mm - 6,000 mm
Height: 1,350, 1,600, 1,450, 3,140 mm

Nabertherm markets this range of top-hat furnaces for bending and slumping of large glass parts. The standard furnace is equipped with one table running on rails which can be pulled out for easy charging. ...

Maximum temperature: 120 °C - 300 °C
Width: 380 mm - 2,150 mm
Height: 620 mm - 2,200 mm

... guided pulleys. Feasible are as well electric and pneumatic lifting doors. Constructions with sliding doors are preferred with low ceilings. With on grade loading lifting doors require an immense total height of the oven. Options ...

Maximum temperature: 100, 350 °C
Width: 480 mm - 4,700 mm
Height: 330 mm - 800 mm

... material electronic PID temperature control with load circuit contactor or solid state relay temperature control with self-improvement function, process alarm for further processing available multi-tank ...

Maximum temperature: 0 °C - 450 °C
Width: 530 mm - 1,400 mm
Height: 950 mm - 1,950 mm

... removes the humidity. The ovens are of robust manufacturing and simple to handle. They are reliable and of low noise. The good insulation saves energy. Design and construction of special ovens are available ...

Maximum temperature: 500 °C
Capacity: 7,000 cm³

Furnace for the casting of low-melting metal alloys equipped with insulated lid for a higher energy efficiency. Moreover, it’s provided with a digital thermoregulator, which allows to set the temperature, and a timer ...

Maximum temperature: 500 °C
Capacity: 18,000 cm³

Furnace for the casting of low-melting metal alloys equipped with insulated lid for a higher energy efficiency. Moreover, it’s provided with a dual digital thermoregulator, which allows to set and check the temperature, ...

Maximum temperature: 500 °C
Capacity: 33,000 cm³

Furnace for the casting of low-melting metal alloys equipped with insulated lid for a higher energy efficiency. Moreover, it’s provided with a dual digital thermoregulator, which allows to set and check the temperature, ...

CureView is a test panel gradiënt oven equipped with 32 individually controlled IR-heaters. The system makes it possible for researchers and qc-personnel to test coatings, raw materials and chemicals at different temperature ...

Width: 1,300, 1,550 mm
Height: 1,420 mm

... maintenance cycle and enables maintenance in a short time period Environmental-conscious • The internal structure of the oven is redesigned to contribute to carbon neutrality, further reducing the amount of electricity ...

Maximum temperature: 950, 1,000 °C
Capacity: 75 l - 1,250 l

Fusing furnacesT max 1000 °CFusing furnaces for temperatures up to 1000 °CWide range of standard furnaces, as well as production of customized furnacesHigh-performance infrared heating in the hood > Optimal temperature ...

Maximum temperature: 1,100 °C
Capacity: 23, 30, 65, 120, 250 l

Inert-gas Retort Furnaces Retort furnaces are suitable for heat treatment processes that must becarried out under a defined atmosphere, such as bright annealing, tem-pering or soldering. The product program ...

Maximum temperature: 450, 250 °C
Capacity: 1,500 l - 18,500 l

Air-circulation Chamber Furnaces KT 1500/02/A – KT 18500/04/AT max 250 °C and 450 °CAll furnaces available as electrically heated or indirectly with gasFurnaces for temperatures up to 250 °C and 450 °CHorizontal ...

Maximum temperature: 220 °C

Electric powder curing oven Technical Specifications 1 - Thermoblock 2 - Temperature 3 - Doors with hinges - 2 pcs 4 - Transportation - Rails

Maximum temperature: 220 °C

1 - Thermoblock 2 - Temperature 3 - Doors with hinges - 2 pcs 4 - Transportation - Rails & Car

Maximum temperature: 220 °C

... 3Insulation of walls and roof - 1set - Mineral wool 75 (kg / m³), thickness 150 (mm) 4Fan - 1pc - 2600 (m3/h) 5Electric motor - 1pc - 1.1 (kW) 7Thermal power - - 14(kW) 8Doors with ...

Width: 1,430 mm
Height: 2,450 mm
Depth: 2,280 mm

... adjustable air ports to meet the special requirements of different products, different seasons on baking quality; 4) The furnace slant board can automatically lift the opening and opening of the door, and the trolley ...

Width: 1,820 mm
Height: 2,450 mm
Depth: 2,600 mm

... adjustable air ports to meet the special requirements of different products, different seasons on baking quality; 4) The furnace slant board can automatically lift the opening and opening of the door, and the trolley ...

Width: 1,210, 860 mm
Height: 760, 770 mm
Depth: 870, 1,110 mm

... functions; 4) Configure the fan in the hot air circulation furnace to configure the fan, and the heat distribution is uniform, ensuring the quality of the baking; 5) The height of the furnace can be ...

Maximum temperature: 500 °C
Width: 1,070 mm
Height: 1,150 mm

The compact soldering system VADU 100 is equipped with separate zones for soldering and cooling and can be operated with paste as well as preforms. Due to its small dimensions and the easy operation, the batch system is very suitable ...

Maximum temperature: 0 °C - 500 °C
Width: 1,330 mm
Height: 1,200 mm

The compact soldering system VADU 100-I operates primarily with preforms and generates void-free solder connections. It is equipped with separate process zones for soldering and cooling. The soldering area is divided in two controllable ...

Maximum temperature: 0 °C - 400 °C
Width: 1,200 mm
Height: 1,680 mm

The soldering system of type VADU 200XL-W is equipped with two separate process chambers and can be operated with paste as well as preforms. The VADU 200XL-W enables the soldering of wafers up to 12 inch. Customized carriers are also ...

Maximum temperature: 5 °C - 250 °C
Capacity: 30 l - 1,000 l
Width: 500 mm - 1,250 mm

... Fan Forced Drying Ovens • Ideal for drying and sterilization with reduced processing time. • Steel outer body coated in corrosive resistant epoxy paint. • Stainless steel AISI 304 Internal chamber with rounded corners. • ...

Maximum temperature: 5 °C - 200 °C
Capacity: 52, 12, 30 l
Width: 500, 600, 730 mm

OVD Series Vacuum Drying Ovens • Ideal for carefully controlled processing such as desiccating and vacuum drying. • Electronic temperature controlled by PID microprocessor and PT 100 probe, one ramp. • ...

Maximum temperature: 5 °C - 120 °C
Capacity: 1,000, 500 l

Glassware Drying Ovens • Electronic temperature control by PID microprocessor and PT100 probe. • Fan forced – on/off. • Toughened glass door (safety glass). • Powder coated steel exterior. • Stainless ...

... cylinder by steam the reduction reaches the 87% ; this is the reason why our furnace is the only one that can be easily installed in urban areas. Rotating burnout furnaces for the annealing of molds ...

FURNACE F50 PILOT Automatic electric, gas or LP furnace to cast alloys featuring a protection shield for greater energy savings. This furnace also has a digital ...

Maximum temperature: 20 °C - 200 °C
Capacity: 90 l
Width: 790 mm

... Compared with traditional ovens, the explosion-proof oven can effectively eliminate the explosion caused by baking and prone to expand objects or operations due to excessive internal air pressure oven ...

Maximum temperature: 10 °C - 150 °C
Capacity: 1,560 l
Width: 1,500 mm

... Presentation Product Features: 1. Three layers oven designed with separate touch screen temperature controller; 2. A large flow of wind turbine and blower in the ovens to achieve high-efficiency temperature ...

Maximum temperature: 10 °C - 300 °C
Capacity: 42 l
Width: 650 mm

The precision oven is a floor-type hot air circulation drying oven equipment selection with a digital display temperature control system and over temperature controller, which can perform intelligent ...

Maximum temperature: 1,200 °C
Width: 450 mm
Height: 600 mm

... Features Furnace Shell The shell is made of metal Q235 low-carbon steel, and the surface is electrostatically resistant and anti-corrosion. Strong metal frame shell structure, low furnace surface ...

Maximum temperature: 1,200 °C
Width: 300 mm
Height: 300 mm

... Features Furnace Shell The shell is made of metal Q235 low-carbon steel, and the surface is electrostatically resistant and anti-corrosion. Strong metal frame shell structure, low furnace surface ...

Maximum temperature: 1,700 °C
Capacity: 192 l

... Features Furnace Shell The shell is made of metal Q235 low-carbon steel, and the surface is electrostatically resistant and anti-corrosion. Strong metal frame shell structure, low furnace surface ...

... uniform cooking. 30 minutes timer with sound signal and automatic disconnection to set the working time of the oven. Pratical power selector switch with 6 positions for cooking, heating, ...

Straightforward, compact and powerful, these three ovens stand out for their easy use. Complete with a 30-minute manual timer, three power levels, a start button and a luminous display.The door opens ...

Maximum temperature: 0 °C - 330 °C

Compact and sturdy structure, designed to hold up other ovens or one Vetrinetta pizza displayer. - Made from AISI 304 stainless steel. - Shock-proof stainless steel heating elements. - Galavanized steel grill. - ...

Maximum temperature: 180 °C - 220 °C

OVERSATIL Series polymerization ovens developed by SciTeeX are designed to ensure optimum curing conditions for the powder applied to a workpieces surface, by heating it to a temperature of 180ºC to 220ºC. At ...

INDUSTRIAL DRYING The use of metal resistors with predictable thermal inertia makes it possible to generate heat with a high degree of accuracy. In addition they do not pollute their surrounding gas which may, for example, be used ...

... . Description : Drying tunnels and ovens after washing and liquid paint application Baking tunnels and ovens for powder paint application Ovens and tunnels for composite materials Single-unit ...

... for optimum oven length and baking results Formats 270 x 370 mm and 290 x 460 mm Gas or electrical heating Double insulation of oven chamber for optimal energy exploitation and working conditions Side ...

ICE CREAM CONES OVENS Specifications Used for the fully automatic production of molded ice cream cones and cups Modular design, 12 to 36 baking moulds, easy capacity upgrading possible They have a capacity of up ...

Maximum temperature: 40 °C - 250 °C

... by LTE, is a laboratory oven with up to 3 temperature profiles that can be programmed in one cycle. The unit has process and delayed start timers which can be set up with 1 minute to 99 hours and 59 minutes. The laboratory ...

Maximum temperature: 0 °C - 970 °C

Thermo-Carb-Q Series Hardening batch furnaces with optional quench Main Features: • Flexible operations • Hardening can be performed in liquid or gas • Single-block plant forn an easy installation • Load weight ...

Maximum temperature: 100 °C - 600 °C

Lo Batch Series Tempering batch furnaces Main Features: • Flexiblility • Available in electric or gas version • Powerful and uniform atmosphere circulation • High efficiency • Fast treatment • ...

... T-REX series - continuous pusher furnaces - has been developed to obtain the separation between the different carburizing phases that require different atmosphere and temperature values. The furnace ...

EB/PVD SMART Coater Vacuum Turbine Blade Coating for thermal barrier coating Short campaign times Small investment costs High part flexibility Small floor space requirements/ no pit One man operation and service ...

... offered at the ALD in-house furnace for than 15 years ALD is running an in-house furnace for the purpose of testing new components, offering the possibility to perform test melts of customer material ...

ESR Electroslag Remelting has been known since the 1930s, but it took approximately 30 years before it became an acknowledged process for mass production of high-quality ingots. The ESR technology is of interest not only for the production ...

Diablo (S) series are very compact pyrolysis ovens, recommended for cleaning of small tools, mainly for the removal of plastics like PP, PE, PVC. Typical use is cleaning nozzles, extrusion dies, spinnerets, filters, spinpacks. ...

Diablo (L) are designed especially for screw cleaning, without disassembling the screw. Screws for extrusion, screws from injection molding are cleaned in a low oxygen environment. Cycle time is 1,5 to 4 hours. The screw cleaning equipment ...

... chamber and is easily accessible from both sides using a hoisting system or forklift to load the parts. Santana pyrolysis ovens are designed for paint stripping and removal of plastic, paint or other organic coating ...