Many routine machining jobs can be done with standard tools. To significantly improve system performance however, special tools are needed. A manufacturer who recently approached LMT Belin with the goal of producing fuel pumps more efficiently ...
One-piece solid carbide tools developed by LMT particularly for die and mould making exhibit enormous performance. It is primarily the special cutting edge geometries and the coatings developed by LMT that lie at the root of this success. The ...
Diameter : 0.8 mm - 4 mm
Length: 31.5 mm - 56 mm
Diameter : 1 mm - 20 mm
Length: 32 mm - 104 mm
Titanium two flute spiral design provides longer life and better chip removal Split point tip increases speed Laser engraved numbers increases step visiblity 1/4" hex shank Optimized for impact driver usage Works ...
Self feed spur for fast material penetration Dual cutting edge for maximum durability in nails Hardened alloy steel provides superior bit life 7/16" Ball groove shank allows for quick bit changes
Diameter : 0 mm - 13 mm
Diameter : 10 mm
Drill for counter boring has great performance. Spot facing machining capability for a wide range of applications such as spot facing on slope, correction of eccentric holes, and thin plate machining. Aqua EX Coating Better ...
Diameter : 3 mm - 6 mm
Length: 30 mm - 60 mm
Developed Long Shank and Regular for Flat drill series 2D flat hole drilling with 10D ejecting length.(industry's longest) Solid carbide drill for 4D flat hole. Applicable for cutting wide range of material From carbon ...
* Aqua coating has a self-lubricant and offers superior heat resistance. (Composite and multi-layered TiAIN + original lubricant film) * Tough micro grain carbide enables a longer tool life. * Dia. 3, 4, 6 , 8, 10, 12, 14, ...
Clamping on labeled portion may prevent the tool from working correctly (due to the built-in anti-vibration mechanism). Therefore, minimum tool overhang should be 3.5D.
Achieving high precision machining in ultra-high efficiency machining Maximum feedrate of 7,500mm/min Modular extension arbor combined with a shank with run-out adjustment mechanism provides a higher degree of freedom for tool overhang. ...
Diameter : 4 mm - 36 mm
Length: 80 mm - 110 mm
Longer lifetime Less force needed Improved cutting performance Smooth cutting Minimum burr
Diameter : 10 mm - 500 mm
Length: 400, 500 mm
Application Areas Wet drill bits for drilling in reinforced-concrete asphalt, as well as natural and artificial stone from Ø 10 - 500 mm Dry drill bits for drilling in masonry, lime sand brick, poroton and other light building ...
Diameter : 6 mm - 67 mm
Length: 400, 500 mm
Application Areas Special wet drill bits for drilling in natural stone, granite, marble, (double) baked brick, masonry, (reinforced) concrete, glass or hollow brickwork from Ø 6 - 67 mm Typical areas of application are HVAC&R, ...
Diameter : 5 mm - 25 mm
Length: 110 mm - 600 mm
For fitting in SDS-plus chucks For rapid drilling in concrete, masonry and natural stone Advantages SDS hammer drill bits of proven MÜPRO quality High-quality hard-metal cutting edges
Bore diameter: 0.5 in - 1.2 in
Incorporating a special dampener mechanism, X-Bar Boring Bars eliminate chatter for extremely fine finishes and extra long tool life. Providing smooth finishes at up to 6X L/D, the X-Bar is ideal for extended overhang applications. Costly ...
Bore diameter: 1 mm - 2.5 mm
These boring bars feature proven lock pins for negative rake geometry inserts. They are ideal for unground, negative rake inserts or utility and precision ground inserts. Integral coolant delivery versions are available.
Diameter : 0.13 in - 0.5 in
Clean, burr-free holes Eliminates the need for specific sized standard drill bits Enlarges holes and deburrs Makes slots into rounds or rounds into slots 135° fast starting drill point requires no center punching High speed ...
Diameter : 8.5 mm - 19 mm
To guarantee a drilling of quality, DUBUIS proposes you several models of reamer drills adapted to the bond diameter and to your need: - boring in the middle of the material, then reaming in one operation only; - reaming to the nominal ...
The Holy Grail among handy guys and gals, this Craftsman 100-PC Accessory Kit has everything you need to get the job done. Rather than build your tool set bit by bit, save time and money with this versatile all-in-one kit. Equipped with ...
Bore diameter: 6 in - 95 in
Hydratight's 8200 Boring Bar is perfect for large boring applications in turbines, stern tubes, rudder posts, struts, missile silos, hinge covers, bearings, gun mounts, large earth moving equipment, valve chambers, wicket gates and seal ...
Bore diameter: 4 in - 26 in
The Hydratight 2500 Boring Bar is a compact and versatile portable line boring system. Despite its small size, the 2500 model is a real work horse. The 2500 Boring Bar utilises a steel acme feed screw to feed the cutting tool along the ...
For steel pipe Ø 1/8” to 2”. Ratchet handle with 18 mm square drive. 5 hardened forged steel cutting blades.
Diameter : 11 mm - 22 mm
Tap seat grinding tool. Spring holds cutter in contact with the tap seating. Cutter with serrated underside, screws on to cutter-holder. M7 thread. Taper ensures a correct fit on the head of the tape. Cutter-holder no.1 : internally ...
Diameter : 4 mm - 16 mm
Length: 75 mm - 150 mm
Forged steel with tungsten carbide tip for durability. Optimised design for fast and accurate drilling of concrete, stone and brick.
Diameter : 1 mm - 13 mm
Length: 34 mm - 151 mm
C.K 135° split point HSS drill bits are designed for the fast and effortless penetration of metal. Easy start, split point tips prevent ‘drill walk’, and ground flutes provide greater accuracy compared to rolled flutes for a cleaner cut.
Diameter : 16 mm - 48 mm
Length: 85 mm - 144 mm
Both Tr nut type and SSMA nut type are available in many sizes. SSMA nut type is suitable for use with drilling chuck.
Length: 109 mm - 152 mm
Diameter: 2 mm - 30 mm
Chamfering, countersinking and corner rounding with machining center and milling machine. Back chamfering with axially adjustable machines such as machining center and milling machine.
Logarithmically relief ground and produced according to customer requirements.
Diameter : 0.35 mm - 8 mm
Length: 30 mm - 79 mm
Carbide twist drills Type I/L (Shank = Drill-Ø) are available from stock. Design with reinforced shaft, twist angle 24°, left hand cutting. Special dimensions and designs available upon request.