|
|
- Very quiet System
- Weak Maintenance
- Common Motorization to some extent right and curve
- Accumulation weak push
Conveyers with rollers ordered by countershaft and round belts
- Frame made out of flanged sheet 25/10ème, Gray completion Epoxy RAL 7035 or blue 5002
- Rollers steel zinc coated Ø50, hexagonal pin 11 mm on dish, 2 throats
- Motor reducers under the apparatus, supply voltage: 220 - 380V. Speed fixes 10,15,20,25m/minute
ON REQUEST
Transfer, push rods, obstinate pneumatic, brake of zone, other dimensions,
shifting of speed
Accessories (foot, guidance, thrusts, etc) are to be ordered separately.
|
|
Controlling of Zero-Pressure Systems
Rollex Drive-System makes the use of Zero-Pressure Systems easier. By simple combining of the single components with the Control-Board (Modular Principle) complex systems can be used very fast and cost effective.
The Zero-Pressure Switch has an integrated logic. It is able to communicate with other sections and so to regulate the flow of materials. The drive will only be switched on, if a load passes the Light Barrier of the Section, after leaving the Drive is automatically switched off.
The sectional switchs of the Electro Magnetic Clutch System Type 526E allows the additional mounting of a break. So the loads stop fast and smooth in case of stopping the section.
The Zero-Pressure Switch can be used without complicated controls and operates with all Rollex 24V Drive Systems perfectly.
|
|
|
Low pressure accumulation driven roller conveyor for unit loads up to 40 kg/m
|
|
|
|
|
|
Automotion's AutoRoll motor driven roller (MDR) conveyor is quiet, safe, low maintenance and offers non-contact zero pressure accumulation. AutoRoll conveyor features "run-on-demand" zones, reducing energy consumption and noise.
Automotion's motorized roller conveyor line is the most complete in the industry. It is available in several pre-configured modular conveyor figures, including straights, curves, inclines, declines, merges, diverts, and transfers. Our bi-directional heavy-duty transfer alone is one of the best performing mdr transfers available.
- Featuring the Itoh drive roller and Itoh control card.
- Quiet, energy efficient, safe operation. Turns itself off when no cartons are present.
- Designed to handle cartons and totes up to 75 pounds in weight.
- PLC control with accumulation logic in the Itoh control card. Network control available.
- Available in:roller or belted configurations, rollers Low-in-frame or High in frame
- 3" roller centers and tight-pack curves available
- Extensive list of pre-engineered figures: straights, inclines/declines, curves, merges, diverts, transfers and sort stations.
|
|
The model 199-CREZD is a chain driven live roller conveyor designed to handle cartons or pallets in conditions not suitable for belt driven rollers. Items are accumulated with Zero Back Pressure reducing the possibility of collisions that may result in product damage.
- Bed - 3-1/2" x 7 ga. formed channel on side opposite chain guard and 4-3/4" x 7 ga. formed channel on chain guard side
- Rollers - 1.9" dia. x 9 ga. unplated rollers spaced every 4" or 6"
- Overall Frame Widths: 18", 20", 22", 24", 26", 28", 30", 34", 36", 40" & 42"
- EZDrive - 1/3 HP Shaft mounted gearmotor located near center of each zone
- Adjustable Floor Supports Available
- Capacity - Maximum load per linear foot of conveyor - 150 lbs with supports on 10 ft. centers, 250 lbs. with supports on 5 ft. centers. Not to exceed 1000 lbs. per zone
|
|
ACCUMULATION CONVEYORS
Technical Characteristics
- Stainless steel bed, folding, 2mm thick
- Steel or PVC roller system
- Metal chain-drive on plastic sliding profile
- Possible to have PVC or steel rollers
- Driven by sprocket and chain under boot and automatic tension regulator
Function
The conveyors enable the accumulation of parcels or cases on the right-hand side.
|
|
Roach® SMART ZONE® is a series of zoned, zero pressure accumulation conveyors utilizing photo sensors to detect presence of product rather than mechanical sensor rollers.
Smart Zone models
- SZ196ZPA Medium Duty Belt Driven Zero Pressure Accumulator
- SZ251ZPA Heavy Duty Belt Driven Zero Pressure Accumulator
- SZA192CDA Medium Duty Chain Driven Zero Pressure Accumulator
- SZD192CDA Medium Duty Chain Driven Zero Pressure Accumulator
- SZA251CDA Heavy Duty Chain Driven Zero Pressure Accumulator
- SZD251CDA Heavy Duty Chain Driven Zero Pressure Accumulator
- SZ796LSZ Medium Duty Line Shaft Driven Zero Pressure Accumulator
|
|
|
Accumulation roller conveyors in mechanical (for continuous skids) and pneumatic versions are used for zero pressure accumulation zones of pallets, grid boxes and other load handling items. This helps to even out fluctuations in output, perform dispatch buffering orprovide powered (low racks)
|
|
The accumulation conveyor Type 5330/5350 is ideal for transporting goods in cartons, cases, containers, baskets and skids. The accumulation process follows the friction principal, meaning that traffic across the conveyor causes the rollers to glide along their axes. Forces driving the rollers are determined by the weight of goods being handled.
Technical Data:
- Load Range: 0 N/m to 2500 N/m (0 kg/m to 250 kg/M)
- Speed (V): 0.1 m/s (6 m/min), 0.2 m/s (12 m/min), 0.3 m/s (18 m/min)
|
|
|
The OAI clean room compatible conveyor is available in several styles suitable for a variety of material handling applications. The C2000 roller style intelligent conveyor offers certified Class 1 clean room compatibility for those critical applications in process areas that demand the lowest level of particulate contamination. The length of conveyor is segmented into nine-inch long zones Each zone is independently controlled by a control card which is networked to adjacent control cards and higher level system hosts.
|
|
- Connection on STANDARD element of conveyer TRL
- Curve with double lines of cylindrical rollers
- Rollers zinc coated steel or PVC Ø50mm, Axis 8mm
- Frame 50/10ème, gray completion Epoxy RAL 7035 or blue 5002.
- Interior Ray: 800mm
- Not of the rollers on average radius: 75mm with 86mm
Accessories (foot, guidance, thrusts, etc)
are to be ordered separately.
|
|
Curve of conveyor with motorized conical rollers.
Frame: tack welded, painted
Ray: interior ray 500 mm
Rollers:
base cylindrical Ø 30 X 1,5 mm out of zinc coated steel,
conical Pots PVC
with pinion doubles 3/8 Chaine steel
with bracelet in cascade
chains on the external ray
Entraînement:
Motor reducer 230/400 V, 50 Hz, IP 54,
fixed Speed: v = 10 m/mn,
Capacity: maximum loading 40 kg
Support doubles adjustable steel height
Accessoires:
Feet supports
Guides bilateral
Interrupteur M/A for a direction of walk
Variable speed transmission
|
|
The 45 and 90°-bent free wheel conveyors Comarme belonging to the series "RCR" consist of sturdy lateral shoulders made of anodised aluminium sheet. The supporting stands are telescopic and made of galvanised sheet steel, with aluminium square pipe legs and plastic supporting feet. The packages displacement takes place through steel rollers on caged balls.
- Structure shoulders extruded aluminium 25x70 mm
- Rollers diameter 48 mm made of steel,assembled on bearings, with steel pin
|
|
The 138 Spool Curves are designed to be slave driven from the 138-NSP Conveyor. Curves are used when turns in the conveyor line are necessary.
- Bed - 9-1/2" deep x 12 ga. formed steel channel frame powder painted
- Rollers - 1-1/2" dia. tapered to 1" dia x 18 ga. and/or 1-3/8" dia. x 18 ga. galvanized rollers
- Overall Frame Widths: 12", 15", 18", & 24"
- Adjustable Floor Supports Available
- Available in 30°, 45°, 60° & 90°
|
|
Gravity roller conveyor curves with conical rollers
By employing conical rollers, the product orientation in curves is maintained.
Only by using such rollers is the exact trace of goods in a curve followed.
Conical rollers are available in various models.
Also available in stainless steel.
|
|
|
The curved roller conveyor is fitted with precisely tapered cone rollers, ensuring the precise running in and out ot totes and cartons. The flat strap drive used with this device also ensures a quiet run. The curved roller conveyor offers first class curve conveying at low cost.
|
|
The Okura Free Curve Conveyors allows a vast flexibility for adaptation to various job conditions and requirements. The Free Curve line allows for extension, bending and shrinking of the conveyor line as the situation and requirement dictates.
SFXD motorised Free Curve conveyor provides for smooth conveyance, together with flexibility in layout for either straight or curved requirements. The ease of curving, expansion or contraction by just the usage of one hand increases operativity sustantially.
|
|
Belt driven live roller is a powered conveyor where the load or product is carried directly on carrying rollers. An endless belt (flat or V-belt) drives the carrying rollers. Adjustable height pressure rollers located below carrying rollers engage the belt with the carrying rollers, providing the power to transport the product. BDLR conveyors are designed for level applications that do not exceed 5 degrees of pitch.
Application :
Belt driven live roller is commonly used to conveyor due to the variety of its applications. Following are a few typical applications:
Transportation
Accumulation
Diverting
Merging
Changing directions (curves)
Carton alignment
|
|
TYPICAL SPECIFICATIONS :
- Frames: 6” x 8 ga. galvanized channel
- Supports: 5” x 8 ga. galvanized channel, adjustable +/- 2”
- Cross bracing: 4” galvanized steel channel
- Support centers: 5’ & 10 ’ dependent on loading
- Rollers: 1.9” x .145 wall; 2 ½ “ x 11 gauge
- Hex axles: 7/16” ; 11/16”
- Sprockets: (2) (50A15) welded plate
- Bearings: pressed fit, 145 lb. and 290 lb. capacity
- Roller capacity: 280 lb. And 570 lb.
- Chain: #40 and #50
- Effective conveying widths: 15” to 51”
- Roller centers: 4” and 5”
- Motors: 1/2 HP TEFC 230/460/3/60 or higher, dependent on loading
- Washdown, TENV and Explosion Proof options available
- All stainless steel construction available
- Motor, Drives and Controls available
|
|
|
Model 254TCDLRC is a medium duty TAPERED ROLLER chain driven live roller curve, designed to transport medium duty loads such as castings, drums or pallet loads. Orientation of pallet loads are maintained when using this chain driven live roller curve.
|
|
A range of products is available that has particularly been designed to meet your requirements on gravimetric filling of containers from 1 kg to 3,000 kg. You can choose from a variety of semi-automatic and fully automatic filling machines. We can offer complete systems for fully automatic packaging processes through the combination of filling equipment with our conveyor and palletising system.
Pallet roller conveyor type RBP.
Design features
- Sturdy construction
- Side structures in stainless steel
- Galvanised roller tubes ø 89mm, thickness of roller tubes
2.9mm, stainless steel possible
- Reversible operation possible
- RBP-HS pallet roller conveyor that can be lifted and lowered
for pallet transfer onto a perpendicularly arranged carrying
chain conveyor
- RBP-DT rotary table with pallet roller conveyor for transferring
pallets onto a perpendicularly arranged pallet roller conveyor
|
|
|
|
|
|
|
The NESTAFLEX PQC all roller power conveyor has a capacity of 100 pounds per linear foot (level surface). It operates on DC drive motors with a 120VAC converter, delivering variable speeds of 0-120 feet per minute, PLUS standard reversible action. The PQC, with its innovative design, requires less storage space when fully retracted and with its ALL-BOLTED construction and durable design, this conveyor is the smart solution for distribution centers where there is high volume cross docking, loading and unloading applications. The PQC models feature ALL-BOLTED construction and Quick Change Heavy Duty Drive Belts giving you added durability and less maintenance down time! Features such as built-in impact conveyor, electronic indexing, zero pressure accumulation, and power assist, make the PQC the next step in automating your application. The PQC is also a smart solution in packaging and manufacturing applications allowing greater product control and maximizing worker efficiency. Like all NESTAFLEX conveyors, the PQC is portable, expandable and can be configured to meet specific material handling needs. The PQC is available using 1.6 inch or 1.9 inch diameter steel rollers.
|
|
The extensible roller belts RE W5OO are available in the following sizes (closed/extended):2 modules 8OO/22OO mm 2 modules 12OO/43OO mm standard version 4 modules 16OO/57OO mm 5 modules 2OOO/71OO mm
RE W5OO - extensible Wheel conveyors, equipped with supports on casters and final retainer.
- Structure shoulders with levers made of aluminium
- Rollers diameter 48 mm made of steel,assembled on bearings, with steel pin
|
|
A proven performer for trailer loading and unloading. Ideally suited for packaging, shipping and flexible assembly lines. Order optional leg connect brackets to lock units together.
- Overall Widths - 18" & 24"
- Flexible and Extendible
- Skatewheels
- Casters with brakes
- Capacity - 200 lbs. per linear foot
- Package Stop
|
|
|
|
|
|
For tough loading and unloading applications, the NTL rigid, drive-out extendable conveyor system is the perfect solution. With its heavy-duty, all-steel construction and oversize wheels, NTL is built to withstand contact in high-forklift-traffic areas.
Powered belt, gravity roller and minimum pressure accumulation make the NTL ideal for trailer applications from 20-55 feet, including distribution centers, parcel/postal facilities, food/grocery applications and third-party logistics. The photo eye flow-control system properly controls package feed to ensure that packages are always present with minimal backpressure, maximizing operator productivity.
With NTL, loading and unloading operations are fast, safe and easy. Controls conveniently located on the front of the boom include belt start/stop buttons, extend/retract buttons, emergency stop, pullout tray brake, extension stop bar, and the optional fan and manual or power steering. The unit's VFD system can flow product at rates up to 150 feet per minute.
|
|
|
The Roach Flexible conveyor was designed for those times when a fixed conveyor is not applicable. Engineered with the workplace in mind the Flexible is built from quality components that can withstand the rigors of loading docks and back room areas while handling a wide variety of materials. Manufactured in the tradition of Roach excellence the Flexible is one conveyor that will last for years to come.
|
|
Pallet powered conveying for loads up to 1 500 kg.
Usable if the side leadings of the pallet are parallel to the handling direction.
Driven roller conveyor ø 89mm, thickness of 3 mm, axle 20mm, tangential driving chain pitch 15,8 mm, galvanized steel rollers.
Top on rollers : 590mm.
2 available device widths: 948 and 1 148mm.
|
|
The free roller conveyors RRB, RRC, type W5OO, W65O, W8OO, are available in the following lengths:375 mm 75O mm 1125 mm 15OO mm 1875 mm 225O mm 3OOO mm
- structure shoulders:extruded aluminium 25x70
- rollers : diameter 30 mm made of aluminium, with steeel pin
RMT
The motorised roller conveyors for packages belonging to the series ""RMT"" consist of sturdy lateral shoulders made of anodised extruded aluminium. The supports are telescopic and made of galvanised steel sheet, with aluminium square pipe legs and plastic supporting feet. Packages are conveyed by anodised aluminium rollers with anti friction loaded nylon bushes. The rollers motorization takes place by means of toroidal belts operated by a motorised control roller. The following tables mention the available items.
|
|
Powered roller conveyors to handle multiformat pallets
Mechanical welded frame : Steel (painted), stainless or galvanized
Rollers coated with zinc, diameter 89 mm, thickness 3.25 mm or 5 mm
Conveying height : From 350 mm to 800 mm ± 60 mm
Load by pallet : 2 tonnes maxi (MARCEAU standard)
|
|
|
|
Roller conveyors
