|
|
| Products 121 to 150 of 170 |
|
|
|
|
AUTOMATIC SAND-BLASTING FOR SMALL PARTS
mod.TAP4
- Work cabin dimensions LxDxH mm: 625 x 600 x 500
- Outer dimensions LxDxH mm: 2400 x 2300 x 2320
- Max weight capacity in belt: 70 kg
- Max volume capacity in tumbler: 31 cu. dm
CHARACTERISTICS
- Belt unit for automatic processing of small metal parts
- Processing of long pieces
- Cyclone for grit separation and recovery
- 4 sand blasting guns
- Automatic movement by electronic control
- Automatic blow
- Operator interface PLC
- Belt rotation speed adjustment
- Automatic inversion for piece unloading
- Machine can operate with pressurized or vacuum systems
OPTIONAL ACCESSORIES
- Filtering cabinet
- Wearproof inside coating
- Automatic opening/closing with safety mechanism
TECHNOLOGY
The TAP4 is specifically designed for the treatment of long pieces and small and medium-sized pieces. The cabin has a load capacity that is higher than the tumbler units.
An ultra-wearproof rubber belt forms a cradle to hold pieces. The movement of the belt and the tabs in the belt impart the rolling of the pieces, which together with the alternating moving of the guns, guarantees 100% coverage of the surface of parts to be treated.
|
|
Guyson's range of Tumbleblast® machines includes the T40 and T50, which offer cost effective blast finishing for batch processing. Tumbleblast systems are ideal for cleaning, deburring, deflashing, cosmetic finishing or surface treatment on small metal components such as screws, bolts, nuts, washers, circlips, fastenings etc.
* Fast cycle times
* Repeatable process quality
* Safe and easy to operate
|
|
|
ALMCO Model ATB-7 shown with process chamber in closed/operating position (inset). Shows patented Smartwheel™ blasting wheel. Photo at right shows the ATB-7 with process door open, displaying peforated, center tracking rubber tumbler belt. Unit is equipped with a Donaldson Torit 5 HP, 1400 CFM dust collection system.
|
|
For semiautomatic blasting of workpieces:
gear, wheels, medical implants, pipes, bars, nails, etc..
A large advantage of this plant is that the parts are always same blasted because of the horizontal nozzle movement and the rotation tabel.
|
|
|
NICOLIS spin blasting equipment is used for automatic precision blasting of large runs of work-pieces up to 250 mm diameter. Their automatic operation guarantees a uniform appearance after blasting delicate mass-produced components.
|
|
|
The Gyra Jet LP is a rotating hand-held tool that directs up to 60,000 psi (4,100 bar) UHP water for surface preparation, industrial cleaning, coating removal, and concrete demolition. Typical applications are removal of damaged surfaces, preparation for recoating or painting, and stripping corrosion and over-spray. The Gyra Jet LP is powered by a Jet Edge intensifier pump.
|
|
completely stainless.
Suitable for clean the surfaces without to hurt the material.
This machines are suitable in form and tool construction.
|
|
ST 1000 N
Our wet blast cabinets provide an optimum solution for the processing of sensitive surfaces. Gentle treatment of the workpieces is guaranteed by the combination of blasting medium with water. Very fine burr removing and roughness depths are no longer a problem. Powerful feed pumps and wear-resistant agitators guarantee optimum wet blasting for continuous use. A specially-designed viewing window with integrated screen rinsing ensures a clear view when blasting. An overflow separator that corresponds to the latest environmental regulations prevents blasting medium or solid material getting into the wastewater system.
|
|
Machine of projection of abrasives with wet process.
The water mixture + abrasive projected on the parts allows very soft treatments on fragile parts and associates the creation of surface quality with degreasing and cleaning.
|
|
| ... products without technical information |
| |
|
|
Sand-blasting, Shot-blasting and Stripping: Equipment and Tooling
