|
|
Ashland Inc. DERAKANE* 8084 epoxy vinyl ester resin is an elastomer modified resin designed to offer increased adhesive strength, superior resistance to abrasion and severe mechanical stress, while giving greater toughness and elongation.
This resin is often used for example as a primer to prepare a substrate surface (steel or concrete) for application of a corrosion resistant lining. The superior elongation and toughness provide FRP equipment with better impact resistance and less cracking due to cyclic temperature, pressure fluctuations and mechanical shocks.
This resin has exhibited chemical resistance across a broad range of acids, bases and organic chemicals for use in many chemical processing industry applications.
* Trademark of Ashland Inc.
|
|
Bisphenolic gelcoats have the maximum heat and chemical resistance compared to all gelcoat groups. Therefore these gelcoats are widely used in chemical industry where high temperature and chemical resistance is necessary.
Polijel 291 is a bisphenolic based, thixotropic, high reactive gelcoat.
It is used for top level chemical and temperature resistant applications.
The most important feature of gelcoat is not effected many chemicals even at high temperature.
Polijel 291 is used especially production of industrial process equipments, chemical tanks, mould production and for surface coatings againts corrosion.
To obtain the maximum resistance levels avoid using pigment and filler much.
|
|
POLYLITE 720-M850 (formerly NORPOL 720-M850) is a medium reactive isophthalic polyester resin with generally good mechanical properties, impact strength in particular. The resin is thixotropic and accelerated.
Features and Benefits
Formerly Branded as NORPOL 720-M850
The resin is specially formulated to resist water, oil and less aggressive chemicals, and is special-ly suited for the production of tanks, pipes, etc.
The resin contains special additives which improve the working environment during and after application due to substantially reduced styrene evaporation.
The resin contains wax which gives the cured laminate a tack-free surface.
The resin is designed for hand lay-up and spray-up application.
The resin is low-exothermic and suited for laminates applied wet-on-wet from 4-10 mm depending on the type of reinforcement.
Availability
Europe/Middle East /Africa
|
|
Unsaturated polyester resins (including vinyl esters and additives) are used in the production of fibre reinforced plastics or non-reinforced filled products.
Due to the ease and freedom of processing, unsaturated polyester resin can be applied in the manufacturing of small and very large structures. Well known in marine and automotive, but also in e.g. wind turbine blades.
As the European market leader, DSM Composite Resins sells their unsaturated polyester resins under the tradenames: Atlac, Daron, Palatal, Palapreg and Synolite.
|
|
|
|
|
|
POLYLITE® 32166-16 is an unsaturated polyester resin developed to produce non-gel coated, solid surface products. Because POLYLITE® 32166-16 is based on isophthalic acid and neopentyl glycol, it behaves similar to a high-quality gel coat which is resistant to discolouration after continuous exposure to water.
POLYLITE® 32166-16 is a pre-accelerated, rigid, medium reactive, low viscosity resin.
POLYLITE® 32166-16 is UV stabilized, stain resistant and is methacrylate modified.
APPLICATION
Room temperature curing of Solid surface.
The use of vacuum is strongly recommended in the manufacture of densified, solid surface products.
FEATURES BENEFITS
Acrylic Modified for higher performance.
Based on Iso and NPG. Only slight bleaching after continuous exposure to
water.
Good stain resistance.
Higher heat distortion temperature.
Superior thermal shock performance.
• Medium viscosity - Permits high filler levels
• High solids content - Excellent filler suspension
• Specially promoted for low cast colour filled
• Controlled gel and cure drift.
• Allows fast production cycles.
|
|
Unsaturated polyester resins (including vinyl esters and additives) are used in the production of fibre reinforced plastics or non-reinforced filled products.
Due to the ease and freedom of processing, unsaturated polyester resin can be applied in the manufacturing of small and very large structures. Well known in marine and automotive, but also in e.g. wind turbine blades.
As the European market leader, DSM Composite Resins sells their unsaturated polyester resins under the tradenames: Atlac, Daron, Palatal, Palapreg and Synolite.
|
|
DION 600-060 is a high reactivity one-pack LP system especially designed for Pultrusion. The resin is based on Isophthalic acid and standard glycols.
FEATURES AND BENEFITS
High reactivity and low viscosity
Good heat resistance
Can be used for Class F (Thermal heat Index 155°C-180°C) laminates
Good fibre wetting properties
Surface smoothness, dimensional stability and reduced internal stress cracks
AVAILABILITY
Europe
|
|
|
Polycor Iso BR brush : viscosity 275 dPa.s thixo index 4.1 ; gel time 9.5 mn ; back up time 45 mn ; solids contents 70 % elongation 3.8% ; density 1.26
|
|
NORPOL FI-177-10 is a low exotherm, light-weight sandwich adhesive, based on a high quality ISO/NPG resin. NORPOL FI-177-10 is accelerated and changes colour from light blue to white shortly after the admixing of peroxide.
•Recommended peroxide dosage: 1.5% low exothermic Peroxide (NORPOL PEROXIDE 19)
•Recommended application temperature interval 18-23 ºC
VARIOUS PROPERTIES
NORPOL FI-177-10 is mainly used to bond single core material sheets together and for bonding core material to GRP laminates.
NORPOL FI-177-10 is formulated for use in vacuum bagging.
The bonding paste should be stored at 18-25 ºC .If the product have a temperature <18 ºC (which is no problem as to product quality) it should be heated to 18-25 ºC before use. See storage and handling document of NORPOL products.
AVAILABILITY
Europe / Middle East / Africa
|
|
Unsaturated polyester resins (including vinyl esters and additives) are used in the production of fibre reinforced plastics or non-reinforced filled products.
Due to the ease and freedom of processing, unsaturated polyester resin can be applied in the manufacturing of small and very large structures. Well known in marine and automotive, but also in e.g. wind turbine blades.
As the European market leader, DSM Composite Resins sells their unsaturated polyester resins under the tradenames: Atlac, Daron, Palatal, Palapreg and Synolite.
|
|
|
|
|
|
The resins in this group enable, hand lay up, spray up and continuous laminating process systems. Automotive parts, city furniture, modular cabins, bus, lorry parts, yachts, boats and similar parts can be manufactured with GRP type resins. Also you can refer to the general purpose resins section for similar resin types.
Polipol 339-T is an orthophtalic based, thixotropic, unsaturated polyester resin.
Polipol 339-T is made for obtaining GRP products from hand lay up and spray up systems. In automotive industry it is used for producing complete cabins and equipment parts, complete tractors and heavy-duty vehicle cabins and caravans.
Also Polipol 339-T is used in the production of yachts-boats and modular cabins.
It can easily wet fiberglass, and it will not drip down vertical surfaces because of its thixotropy. Because of this property, there will be no local shrinkage and this property provides a non-wavy and homogenous final product.
Polipol 339-T can safely be used in fields where big dimensioned perfect surface smoothness is requested like bus, lorry-truck and sea boats-yachts.
Polipol 339-T contains a blue colored Mek-p indicator, its color disappears after a couple of minutes when it's mixed with Mekp. As known the addition of Mek-p to resin is done automatically at the gun section. If there is a malfunction in the pump or a problem in the system, resin's color will not change on the mould and the fault will be understood so the needed
precautions will be taken and big losses could be prevented at the beginning.
|
|
|
Gelcoats provide the decorative and protective outer skin of reinforced plastic laminates. Neogel® gelcoats, developed by DSM Composite Resins, are sold throughout Europe. Neogel is a well respected tradename; particularly within the European marine industry, where it has long been specified by leading boat builders.
|
|
|
Polycor LO-VOC NPG PA application : projection spray viscosité 140 dPa.s , indice Thixo 4.5 ; temps de Gel 9.5 mn ; stratifiable 30 mn , extrait 70 sec %
|
|
|
|
|
|
PRIME™ 20LV - Epoxy Infusion System
- Very low viscosity
- Variable infusion times
- Very low exotherm even in thick sections
- Suitable for infusing very large structures
- Lloyds and Germanischer Lloyds approved
PRIME™ 20LV is the next generation of PRIME™ 20 epoxy infusion system, which is specifically designed for use in a variety of resin infusion processes including RTM (resin transfer moulding), SCRIMP™ and RIFT (resin infusion under flexible tooling).
PRIME™ 20LV has a much reduced viscosity resin and longer working time, which makes it ideal for infusing very large parts with complex reinforcements in one operation. It maintains the exceptionally low exotherm characteristic, which allows thick sections to be manufactured without risk of premature gelation due to the heat of exothermic reaction. This low exotherm will also help to extend the life of mould tools.
PRIME™ 20LV has been used successfully for the single-operation moulding of components ranging from narrow carbon yacht masts, up to 80' yacht hulls and wind turbine blades. It achieves excellent mechanical and physical properties from a moderate (50°C) postcure, offering the finished laminate properties that lie between hand lamination and low-temperature cure prepreg processes.
The PRIME™ 20LV system is available with three hardeners, offering a range of working times and cure speeds. This enables the geltime of the resin to be more closely matched to the required infusion time for any particular size of moulded part.
|
|
Low viscosity epoxy resin system Epilox® M 730 + Epilox® - hardener M 903 is a laminating system with very long potlife. Larger batch sizes in areas with warmer climate are thus processable. The mix is warmed up to 50 °C until gelation has occurred. Post-curing is performed at ca 80 °C.
Curing schedule: Pre-heating of the resin/hardener mix to 50 °C, keeping 50 °C for 30 min, heating to 80 °C, keeping 80 °C for 1.5 - 2 h.
The system is preferably used for sewage renovation because it does not attack polyurethane films which cover the pipes.
|
|
POLYLITE® 516-M880 is a low VOC polyester resin with good mechanical properties suitable for all market segments.
POLYLITE® 516-M880 is accelerated and thixotropic and specially designed for hand lay up and spray up applications.
Features and benefits
Low styrene content <35%
o Reduced shrinkage
o Improved surface aspects
o Reduced styrene emission
Good fibre wetting properties
o Easy lamination and air release
Approvals:
POLYLITE® 516 M880 is approved for boat production by Lloyds Register of Shipping and Det norske Veritas (DNV).
Availability:
Europe/ Middle East/ Africa
|
|
Unsaturated polyester resins (including vinyl esters and additives) are used in the production of fibre reinforced plastics or non-reinforced filled products.
Due to the ease and freedom of processing, unsaturated polyester resin can be applied in the manufacturing of small and very large structures. Well known in marine and automotive, but also in e.g. wind turbine blades.
As the European market leader, DSM Composite Resins sells their unsaturated polyester resins under the tradenames: Atlac, Daron, Palatal, Palapreg and Synolite.
|
|
|
Master Bond Inc. formulates a wide range of one and two component adhesive systems for bonding metals. From aluminum to cast iron to stainless steel to titanium select Master Bond for your specific needs. They will speed productivity, reduce waste, save energy and enhance produce capabilities. Job proven for over 30 years, Master Bond products are employed in industries ranging from aerospace, optical and electronics to oil/chemical processing, medical and automotive.
|
|
No Grinding or Surface Preparation
Plexus Adhesives bond engineered plastics, SMC, FRP, metals, and dissimilar substrates without grinding, surface preparation, or primers. As a result, they eliminate time-consuming and costly operations, lessen process variability, minimize dust, and greatly reduce the problems associated with toxic solvents.
|
|
|
|
|
|
Master Bond formulates a wide selection of metal charged adhesives for numerous industries. Theses include metal repair adhesives with aluminum and stainless steel fillers.
Master Bond’s line of electrically conductive adhesives is the number one choice for the design of tomorrow’s advanced electrical circuitry. Nobody offers more choices or solutions. The Master Bond product line includes silver, nickel, copper and graphite filled compounds. We even offer silver coated nickel systems for low resistance where cost effectiveness is crucial. Specific compounds are designed to cure at ambient temperatures or upon brief exposure to elevated temperatures. The cured products offer high physical strength, superior substrate adhesion and uniform electrical conductivity even upon exposure to hostile environmental conditions. Long term durability is excellent.
Master Bond also manufactures one and two component thermally conductive systems. They include epoxies, silicones and other elastomeric systems. Special formulations for unusual service conditions are available. They include serviceability to 500°F, at cryogenic temperatures, and in high vacuum environments as well as systems that are easily repairable. Designed for easy application, these compounds can be purchased in convenient packaging. They are used on heat sinks, fan sinks, package lids, motor controls, multiplexers, sensors, power semiconductors and thermistors. Toughened systems have been successfully employed in applications requiring resistance to shock, vibration and thermal cycling.
|
|
Stainless steel-filled epoxy putty for patching, repairing and rebuilding stainless steel food processing equipment
KEY FEATURES
* Non-rusting
* Bonds to ferrous and non-ferrous metals
* NSF certified for potable water applications
* Acceptable for use in meat and poultry plants
* Listed under NSN stock #8030-00-268-7934
|
|
Ashland Inc. DERAKANE*and DERAKANE MOMENTUM 470 series are novolac-based epoxy vinyl ester resins designed to provide exceptional mechanical properties at higher temperatures. These resins offer a high resistance to solvents and chemicals, good retention of strength and toughness at elevated temperatures, and excellent resistance to acidic oxidizing environments.
* Trademark of Ashland Inc.
|
|
DION® 9400 is a non-accelerated, Novolac epoxy based vinyl ester resin. This highly cross-linked resin has a high heat distortion temperature and exceptional chemical resistance, particularly towards chlorine and organic solvents. Typical uses are filament winding and hand lay-up of reinforced plastic tanks, pipes and process equipment.
APPLICATION
DION® 9400 is especially formulated for hand lay-up, pultrusion and filament winding applications, and impregnates both glass and aramid fibres rapidly.
FEATURES BENEFITS
• Novolac epoxy vinyl ester resin - Excellent chemical resistance to a wide variety of corrosive environments
• Good chemical resistance towards chlorine
• Good solvent resistance
• Good high-temperature stability
• Compatible with both aramid and carbon fibres
|
|
|
DYMAX light-curable adhesives cure in seconds upon exposure to longwave ultraviolet light and/or visible light. Light-curable adhesives optimize the speed of automated assembly, enable 100% in-line inspection, and increase product throughput. Industrial adhesives are available for plastic sealing, metal bonding, and glass assembly, as well as for joining dissimilar substrates.
|
|
Advantages of Vitralit® UV and light curing-adhesives:
Easy handling
Short curing time for higher productivity
Solvent-free, no heat exposure
Long storage at + 5° c
Very good electrical properties
|
|
one-component acrylates
light-curing, UV-curing (see "curing lamps DELOLUX")
Bonding of modern materials and changed production processes are enabled and supported by continuous redevelopment of DELO-PHOTOBOND products.
Bonding of various raw materials of mobile loudspeakers
The loudspeakers' high quality is ensured by optimum, acoustic properties. High output by shortest cycle times. Bonding of aluminium door hinges onto glass shower cabins
Boreholes or unsightly clamping fixtures are prevented.
Properties DELO-PHOTOBOND:
graded elasticising from hard to tension-equalising enables
bonding of various materials for different requirements
curing within seconds allows short cycle times
Application areas:
Communications electronics
Consumer electronics
Automotive electronics
Plastic and glass processing
You can find detailed information about radiation curing in our brochure „Radiation curing“.
|
|
NORPOL FI-170 is a multi-purpose bonding paste based on special polyester resins combined with selected fillers and additives.
NORPOL FI-170 is pre-accelerated and has a white colour. NORPOL FI-170 changes colour from bluish white to white in <5min. after the admixing of peroxide.
•Recommended peroxide dosage: 1.5% MEK Peroxide (NORPOL Peroxide 1)
•Recommended application temperature interval 18-23 ºC
•Sag/flow: Will not sag provided a maximum thickness of 15 mm is observed. Not horizontally self-flowing.
Applicable as a general purpose bonding paste.
VARIOUS PROPERTIES
Suitable surfaces: Glass-fibre reinforced products and cellular plastics.
Workability: Hard to grind.
The bonding paste should be stored at 18-25 ºC. If the product is below a temperature of 18 ºC (which does not affect product quality) it should be heated to 18-25 ºC before use. See storage and handling document of NORPOL products.
AVAILABILITY
Europe / Middle East / Africa
|
|
The GRAVICOL® range of bonding pastes are designed for the assembly and bonding of glass reinforced plastic moldings. All of the bonding pastes in the range are pre-accelerated and require only the addition of a
standard MEKP catalyst. The pastes can be used for bonding two parts, insert panels, core materials. They can also be used for cavity filling and as an aid to lamination to help reduce the chance of air voids. When designing the bonding pastes there are several key areas we look at and control to
suit the numerous application areas of the pastes : - Gel/Cure Times - Low Shrinkage Levels - Application Methods - Mechanical Properties
|
|
NORPOL® GI is a family of general purpose gelcoats based on a premium ISO polyester resin. NORPOL® GI gelcoats are available in both spray and brush versions.
•Recommended peroxide dosage: 1.3 - 2.0%
•Recommended film thickness: 0.55-0.85 mm (wet film)
Features and benefits:
•Excellent application properties and processing robustness
o Easy flow and leveling
o Superior air release
o Excellent curing properties
o No colour separation
o Easy to sand and repair
•Good weathering resistance
o Low Colour change compared to conventional ISO/NPG gelcoats
o Gloss retention similar to conventional ISO gelcoats
•Good mechanical properties
•VOC content and emissions similar to conventional gelcoats
•Applications include industrial parts, car bodywork, cladding panels, roof canopies, windmill nacelles etc.
AVAILABILITY
Europe / Middle East / Africa
|
|
|
|
Resins, Gelcoats for Composite Materials
