|
|
EV100 contactors are designed for use in DC applications with lead-acid batteries or rectified power. They perform power switching functions for electric vehicle traction drives as well as pump and other power switching applications.
The contactors have been successfully applied to meet UL standards, and are listed under UL file number AU1793.
- Amp ratings :100, 150 and 300 amps at 50% Duty Cycle
- Voltage : 24 to 80V
Features and Benefits:
- Special bonding of alloy tip material to tip supports maximize tip life.
- Double-break operation assures good contact and minimizes tip bounce time.
- Solenoid design allows for smaller size and mounting flexibility.
- Design criteria optimizes tip velocity, pick-up time and low-voltage operation for improved performance with solid-state controllers.
- High-fidelity mechanical operation assures consistent high tip parting velocities.
- Mechanical life in excess of six million operations
- Electrical life in excess of two million operations. Actual life will vary depending on application, duty cycle, maintenance and battery condition. |
|
| ... products without technical information |
| |
... see all the products in the category
Contactors
|
The DC energy systems from FAC P series of SALICRU are rectifiers specially designed to supply direct current to the most varied equipment
of medium and high power. Manufactured in power rates of 1000, 2000, 2700 and 5000 W, allow being connected in parallel and built in
19 cabinets, where each cabinet can also include a monitoring and management unit (MS-102), batteries and DC outgoing distribution,
as well as load priority systems. Besides, each rectifier module can be hot swapped for its connection and removing, with all the advantages
that it means in the system operating.
On the other hand, thanks to the high quantity of rectifier modules that can be connected to one system only, allow having power rates
higher than 170 kW.
The monitoring and management unit (MS-102) controls the complete system, also it stores and manages the input, output and battery
data; and allows setting all the parameters on it. The rectifier modules communicates with it through the RS-485 port, and permanently it
is controlling the output voltage, current sharing among the modules, battery charging current, critical and non-critical load contactors,
the end of autonomies, etc. The external communication can be done in local or remote modes (GSM / TCP-IP). |
|
| REO build a range of variable output DC power supplies that operate on the switch mode principle. The variable output is produced by high speed switching of the mains supply, after rectification, using IGBT's and controlling the mark space ratio. The DC level is reduced to the required output range by employing REO high-frequency transformers. Smoothing components, also manufactured by REO, are used to give a steady, ripple free DC supply. |
|
Features:
- UL-recognition (in preparation) marking for worldwide
applications.
- Designed for power ratings from 120 to 960 W. |
|
1U High, Up to 450 Watts with PFC and Hot-Swap Provision
FEATURES
- Includes Isolated 5V, žA Standby Output
- Hot-Swap Operation
- 12, 24 or 48VDC Outputs
- I2C Serial Data Bus Option
- Integral LED Status Indicators
- Up to 5.6 Watts/Cubic Inch
- Power Factor Corrected
- Low Profile: 1.6 Inches (41mm) High
- Single Hot-Swappable Connector
- Staged Pin Engagement
- ORing Diodes on Output
- 1U, 19" Racks Hold 2 or 3 Units*
- Active Current Sharing
- Universal 85 to 264VAC Input
- Class B EMI Input Filter
- Optimized Thermal Management
- No Minimum Load
- Control & Monitoring Features
- Front-End Switcher - PCG & TPCG
- SEMI F47 Compliant at Hi-Line |
|
The B+K 1692 Switching Mode DC Power Supply provides high current output in a lightweight and compact package. It is suitable for a variety of uses, especially for powering DC operated mobile radio equipment on the bench. It provides a variable voltage output from 3V to 15V at 40A continuous operation. In addition a fixed 13.8 VDC output is also selectable by a slider switch. Switching mode power supplies have the advantage of lightweight and high efficiency when compared to traditional linear mode power supplies. The efficiency can exceed 80% under the best conditions. Advanced circuitry protects against overload and provides immunity from RFI. A bright red and green LED display provides for an accurate and highly readable indicator of settings.
Lightweight and compact
High efficiency
Current fold back circuitry with illuminated indicator prevents overloading the power supply
Over temperature protection circuitry
Over voltage protection prevents abnormal high output voltage
High RFI stability
Variable output 3V to 15V at 40A
|
|
80 Models: 16 to 1000 Vdc, 20 to 4500 Adc
Series and parallel master/slave operation
High dielectric withstand: 2500 Vac
50 Hz to 400 Hz input frequency
All user interface circuitry referenced to earth ground
OVT and OCT shutdown standard
Automatic V/I crossover
RS232 interface with SCPI commands
Optional IEEE-488, RS485, and Ethernet programming
Front panel potentiometers for stepless rotary control
Front panel calibration
User friendly controls and indicators
Remote Interface Software with self-teaching features
Drivers: Certified LabWindows/CVI and LabVIEW for GPIB, Serial, and TCP/IP communications
Load dependent cooling
High power factor
CE Mark
Magna-Power Electronics MS SERIES combines the best of dc power processing with multiprocessor embedded control. A combination of high and medium frequency power processing technologies improves response, shrinks package size, and reduces cost. MS SERIES power supplies are current fed and are more tolerant to abusive loads than conventional switching power supplies. |
|
80 Models: 16 to 1000 Vdc, 20 to 2700 Adc
FEATURES:
Series and parallel master/slave operation
High dielectric withstand: 2500 Vac
50 Hz to 400 Hz input frequency
All user interface circuitry referenced to earth ground
OVT and OCT shutdown standard
Automatic V/I crossover
RS232 interface with SCPI commands
Optional IEEE-488, RS485, and Ethernet programming
Front panel potentiometers for stepless rotary control
Front panel calibration
User friendly controls and indicators
Remote Interface Software with self-teaching features
Drivers: Certified LabWindows/CVI and LabVIEW for GPIB, Serial, and TCP/IP communications
Load dependent cooling
High power factor
CE Mark
Magna-Power Electronics TS SERIES combines the best of dc power processing with multiprocessor embedded control. A combination of high and medium frequency power processing technologies improves response, shrinks package size, and reduces cost. TS SERIES power supplies are current fed and are more tolerant to abusive loads than conventional switching power supplies. |
|
39 Models ranging from 16 to 2500 Vdc to 40 to 7500 Adc
Series and parallel master/slave operation
High dielectric withstand: 2500 Vac
All user interface circuitry referenced to earth ground
OVT and OCT shutdown standard
Automatic V/I crossover
RS232 interface with SCPI commands
Optional IEEE-488, RS485, and Ethernet programming
Front panel potentiometers for stepless rotary control
Front panel keypad and up/down control for digital control
100 memory states with front panel memory indicator
Auto sequencing by time or external triggering
Modulation with addition or multiplication
Front panel calibration
User friendly controls and indicators
Remote Interface Software with self-teaching features
Drivers: Certified LabWindows/CVI and LabVIEW for GPIB, Serial, and TCP/IP communications
High power factor |
|
Features:
54 Models: 5 to 1000 Vdc, 3 to 900 Adc
Series and parallel master/slave operation
High dielectric withstand: 2500 Vac
50 Hz and 60 Hz input frequency
All user interface circuitry referenced to earth ground
OVT and OCT shutdown standard
Automatic V/I crossover
RS232 interface with SCPI commands
Optional IEEE-488, RS485, and Ethernet programming
Front panel potentiometers for stepless rotary control
Front panel calibration
User friendly controls and indicators
Remote Interface Software with self-teaching features
Drivers: Certified LabWindows/CVI and LabVIEW for GPIB, Serial, and TCP/IP communications
Load dependent cooling
High power factor
CE Mark
Magna-Power Electronics PQ SERIES combines the best of dc power processing with multiprocessor embedded control. A combination of high and medium frequency power processing technologies improves response, shrinks package size, and reduces cost. PQ SERIES power supplies are current fed and are more tolerant to abusive loads than conventional switching power supplies. |
|
Safety and reliability continue to gain increased importance in many industrial applications. The family of power supplies offers several solutions to increase the reliability and safety of the application. The N+1 redundancy modules provide a cost effective means for providing back-up power in the event the primary power supply fails. The "Buffer" module provides added reliability for conditions of "Brown-out" when input power is unreliable. The comprehensive line of Switched Mode Power Supplies accepts wide ranges of both AC and DC input voltages and has global certifications to meet worldwide single-phase and 3-phase application requirements. The line of Allen-Bradley Power Supplies has two distinct families the standard and Compact that are essential components for complete low voltage control solutions.
- Reliable Design
- Leading Edge Technology
- Reserve Power and Load Response
- Parallel Connection Compatible
The Allen-Bradley Bulletin 1497 Global Control Circuit Transformers from Rockwell Automation are designed to reduce supply voltages to machine tool control circuits, providing greater safety to operators. These transformers also isolate the control circuits from power and lighting circuits. They are especially designed to accommodate the momentary current inrush caused when electromagnetic components are energized, without sacrificing secondary voltage stability per NEMA ICS2-100. |
|
Fan-less power supplies for computer systems ATX and U1 form factors
Redundant power supplies
Fan, convection and water cooled
Chargers
Standard and custom products
Made in Germany |
|
LoPAC Family - AC-DC Switcher Power Supplies
The LoPAC family consists of three ultra low profile, fan cooled, switching power supplies that combine the advantages of power factor correction (PFC) with high power density. They consist of the PFC Mini, PFC Micro and PFC MicroS. |
|
Switch mode units for DIN-rail mounting.
18 - 30 - 60 and 120 W
Supply voltage: 90-265 VAC
Output ranges:
5 DC - 3.5 A , 12 VDC - 1.5 A, 2.5 A or 5 A
24 VDC - 0.75 A, 1.25 A, 2.5 A or 5 A |
|
Esispower provides several kinds of Switch Mode Power Supplies for specifics applications.
Esispower designs non-standart SMPS's according to customer requirements when it is not available in the standard product range. |
|
| The PVSE 400 is a economical three-phase switch power pack with highly precise output voltage for all requirements of the automatic control engineering. Concentrated on the nuclear tasks tension and of supply of electricity. Highest power reserves of up to 200% owing to power Boost. The Top Boost supplies in the event of an error up to 60 A over rated current, this makes possible a economical securing with automatic circuit breakers. Available as stabilized or semistabilisierte variant, with output rated voltage 10, 20 and 40 ampere, optionally also with DC OK signaling and active starting current delimitation. |
|
| ... products without technical information |
| |
The modular switches disconnecting switches are appropriate with the local cut and the electric cut of the circuits low tension in alternative course but also in D.C. current.
They are usually used for the following applications:
Principal switch
Switch-disconnecting switch cd. 750V and 1500V
Switch of safety engines
The range is available of 1 to 6 poles in gauges 630A, 1000A, 1600A and to 4 poles in gauge 2200A.
Applications: AC and cd. |
|
The modular switches disconnecting switches are appropriate with the local cut and the electric cut of the circuits low tension in alternative course but also in D.C. current.
They are usually used for the following applications:
Principal switch
Switch-disconnecting switch cd. 750V and 1500V
Switch of safety engines
The range is available of 1 to 6 poles in gauges 630A, 1000A, 1600A and to 4 poles in gauge 2200A.
Applications: AC and cd. |
|
JetNet 4706, an improved and strengthen manageable industrial PoE switch, it is designed for industrial PoE applications such as IP surveillance or wireless access points, where power source is not conveniently located. It supports intelligent PoE control and schedule management; each of the four PoE ports can be configured in a weekly schedule by hourly basis and PoE on/off can be remote controlled via SNMP and Web. JetNet 4706 is compliant to both IEEE 802.3af PoE as well as the pioneer standard of IEEE802.3at PoE Plus design (enhancement of 802.3af) for boosting PoE delivery up to 30W in each of the four PoE ports. JetNet 4706 can auto-detect 24V & 48V power input and deliver 24V & 48V PoE output allows more applications where 48VDC is not an option.
*Four 10/100 TX Power over Ethernet ports and two redundant
10/100 TX uplink ports
*DC 24V Power Input for DC 22V output through Ethernet
(Non-standard PoE)
*DC 48V Power Input for IEEE 802.3af 48V PoE output (IEEE 802.3af)
*Up to 30W per port for High Power solution by Power Input DC 55V
(IEEE 802.3at)
*UP to 100W for total power budget
*Support IEEE 802.3af for PoE detection and PoE classification resistors
*PoE control and schedule by hour/weekly basis
*Auto-detect Powered Device status for device auto-reset (LPLD)
*Patented Rapid Super Ring technology (RSR), back up system recovery time less than 5ms
*SNMP v1/v2c/v3, IGMP snooping v1/v2/v3, RMON, LACP, VLAN, QoS
*Network security by IP/MAC address, SSL and SSH
*Built-in hardware watchdog timer for system auto-reset
*Aluminum rugged enclosure with IP-31 grade protection
*Forced mode Powering
*Wide operation temperature: -25~60oC |
|
JetNet 3706 is designed for industrial PoE applications, such as IP surveillance or wireless access points, where 30W per port and/or 24VDC PoE is required. JetNet 3706 is in compliance with both IEEE 802.3af PoE as well as the pioneer standard of IEEE802.3at PoE Plus design (enhancement of 802.3af) for boosting PoE delivery up to 30W in each of the four PoE ports. Redundant 24~55VDC power inputs guarantees your operation will not be stopped due to power disruption. JetNet 3706 can auto-detect 24V & 48V power input and deliver 24V & 48V PoE output, allowing more applications where DC 48V is not an option.
Industrial 6-port Web-Managed PoE Plus Switch
*Four 10/100 TX Power over Ethernet ports and two redundant
10/100 TX uplink ports
*DC 24V Power Input for DC 22V output through Ethernet
(Non-standard PoE)
*DC 48V Power Input for IEEE 802.3af 48V PoE output (IEEE 802.3af)
*Up to 30W per port for High Power solution by Power Input DC 55V
(IEEE 802.3at)
*UP to 100W | | |
