|
|
|
|
|
|
bc637PCIe (GPS)
GPS Referenced PCI Express Time & Frequency Processor
Symmetricom’s bc637PCIe PCI Express timing module provides unparalleled precise time and frequency to the host computer and peripheral systems. Time is typically acquired from GPS or time code signals such as IRIG B.
Extremely Precise time is acquired from the GPS satellite system or from time code signals provided to the host computer. GPS synchronization provides 170 nanosecond RMS accurate time to UTC (USNO) and enables the bc637PCIe to be an ideal master clock for precisely synchronizing one or more computers to UTC.
Integration of the module is easily facilitated with standard drivers for Windows, Linux, and Solaris that included with the module.
Extensive time code generation and translation are supported. The generator outputs either IRIG A, B, G, E, IEEE 1344, NASA 36, XR3 or 2137 in both amplitude modulated (AM) and DC level shift (DCLS) formats. The translator reads and may be used to discipline the 10 MHz oscillator to either the AM or DCLS format of IRIG A, B, G, E, IEEE 1344, NASA 36, XR3 or 2137 time codes.
The module also has a state-of-the-art DDS rate synthesizer capable of 0.0000001 PPS to 100 MPPS. Three Event Time Capture registers provide a means of latching time of external events. A key feature of the bc635PCIe is the ability to generate interrupts on the PCI bus at programmable rates. These interrupts can be used to synchronize applications on the host computer as well as signal specific events.
|
|
|
Advantech is a global leader in plug-in I/O card design and manufacturing, providing a full range of industrial data acquisition (DAQ) and control products which are widely used in industrial and laboratory applications such as: monitoring, motion control, data acquisition, and automated testing. There are six major categories - CompactPCI, PCI-bus, ISA-bus, USB-bus, PC/104 modules, and Motion Control I/O products. With rich wiring terminals and extensive software support, Advantech provides reliable, efficient, and cost-saving industrial solutions. Moreover, Advantech’s DAQ products could simply be bundled with versatile industrial PC chassis, backplanes, CPU modules, flat panel monitors and embedded automation computers.
|
|
|
|
|
|
The interference-free PCI Express boards with numerous protective measures are especially suited for applications in rough industrial environments.
Analog multifunction board APCIe-3121:
- 16 SE/8 diff. or 8 SE/4 diff. inputs, 16-bit
- 8/4 analog outputs, 16-bit
- Optical isolation
- PCI express DMA, programmable Gain
- Trigger functions, timer, watchdog
- 8 digital I/O, 24 V, optical isolated
1- to 8-port serial interface APCIe-7xxx:
- Serial interfaces with modules: RS232, RS422, RS485, 20 mA CL
- Free mode configuration for each port
- with/without optical isolation
- 128-byte FIFO buffer for each port
Multifunction counter board APCIe-1711: for many counting applications on the same hardware base – Programmable FPGA modules
- Functions: Incremental counter, SSI, counter /timer, pulse acquisition, frequency, pulse width, period duration , velocity measurement, PWM, BiSS-Master, …
- Function selection through software
- Optical isolation 1000 V
- Customer-tailored functions
Digital I/O boards APCIe-1532 and APCIe-1516, 24 V:
- 32 or 16 I/O, 24 V
- 15 interruptible inputs
- Reliable switching to „0“ or „1“, even in case of interferences
- Optical isolation 1000 V
- Output current per channel 500 mA
Free drivers for standard operating systems and programming samples.
|
|
|
|
|
|
bc635PCIe (IRIG)
Symmetricom’s bc635PCIe PCI Express timing module provides unparalleled precise time and frequency to the host computer and peripheral systems. Time is typically acquired from time code signals such as IRIG B.
Extremely accurate time provided to the host computer. Integration of the module is easily facilitated with standard drivers for Windows, Linux, and Solaris that included with the module.
Extensive time code generation and translation are supported. The generator outputs either IRIG A, B, G, E, IEEE 1344, NASA 36, XR3 or 2137 in both amplitude modulated (AM) and DC level shift (DCLS) formats. The translator reads and may be used to discipline the 10 MHz oscillator to either the AM or DCLS format of IRIG A, B, G, E, IEEE 1344, NASA 36, XR3 or 2137 time codes.
The module also has a state-of-the-art DDS rate synthesizer capable of 0.0000001 PPS to 100 MPPS. Three Event Time Capture registers provide a means of latching time of external events. A key feature of the bc635PCIe is the ability to generate interrupts on the PCI bus at programmable rates. These interrupts can be used to synchronize applications on the host computer as well as signal specific events.
|
|
This board is an interface board of PCI bus conformity which inputs a digital signal.
The opening-and-closing state of a switch can be inputted.
A maximum of 128 input can be performed on board.
"Attached API function library [API-PAC(W32)] The application software for Windows can be created by the various programming languages which are supporting Win32API functions, such as Visual Basic, and Visual C/C++, by using it.
|
|
|
|
|
|
This product is the interface board of the PCI bus conformity which I/O digital signal.
Digital signal of 12-24VDC can be outputted and inputted.
Input of a maximum of 32 points and output of a maximum of 32 points can be performed in onAttached API function library [API-PAC(W32)] The application software for Windows can be created by the various programming languages which are supporting Win32API functions, such as Visual Basic, and Visual C/C , by using it.
Features:
In order for 16-point unit to carry out common composition, it can common every respond to a different external power supply.
Since the PCI bus (personal computer) and the I/O interface are insulated by the photo-coupler, it excels in noise-proof nature.
32 points of an input signal can be used as an interruption input.
Moreover, the edge of the input signal which generates interruption can also be chosen.
It has the digital filter function for preventing the incorrect input by the noise or the chattering.
The rating of an output signal is a maximum of 35VDC and 100mA per point.
Zener diode is connected to the output transistor for protection from serge voltage. Moreover, the over-current protection element is attached per eight output transistors.
PIO-32/32L(PCI)H, and PIO-32/32L(PCI) are connector pin compatibles.
|
|
|
|
|
|
PCI-X BUS Serial Port Expansion
RocketPort INFINITY cards are flexible, reliable, and high-speed in-server serial port expansion cards. They provide connectivity for applications like factory systems, SCADA systems, point-of-sale, telecommunications, medical systems and traffic equipment. Connect serial devices like printers, scanners, cameras, and LCD screens.
The RocketPort INFINITY product family is Comtrol’s next generation multi-port serial adapter. Products are fully compatible with systems that have 32 or 64 bit 3.3 or 5 volt uPCI and PCI-X expansion slots. The INFINITY design maximizes serial performance via Comtrol’s exclusive high-performance Unity ASIC chip. Cards are low profile and are for use in both standard PCs and low-profile servers. Quad-cabled and octa-cabled products reach serial communication speeds of 921 Kbps and products with an interface communicate at up to 460 Kbps. All products support software-selectable RS-232/422/485 serial communication modes. The product family includes models from 4-ports up to 32-ports with up to 128-ports per system. They provide an infinity of options for connecting and communicating with your devices.
Highlights
32 or 64 Bit 3.3 or 5 Volt uPCI or PCI-X Connectivity
Low-profile or Standard Height Compatible
RS-232, RS-422, RS-485 Software-selectable
4- to 32-Port Interfaces
High Performance Cards with Speeds up to 921 Kbps
RoHS Compliant
Microsoft Certified Drivers for Windows VISTA, Windows XP and Windows Server 2003
|
|
|
|
|
|
Over 132 kinds of boards that ICP DAS has released surely satisfy you with one stop shopping. These boards not only cover from PCI to ISA bus that you would have often seen on your PC but even support universal PCI.
From hundreds of boards, take PCI bus boards for example; they are sorted into three series. PCI series are top-of-the-line ones that reach awesome performance with multiple functions and high resolutions; PISO series are putting emphasis on its protection ability to prevent signal input from direct impact; PIO series are cost-effective ways for general use, and moreover, they are well-suited for high-speed transmission applications.
One thing we must introduce you is that memory boards are so unique that you can find them only in ICP DAS. With two Lithium-polymer batteries, data can be preserved for 10 years. Gambling machines in the casino are usually seen for the application of our memory boards.
Besides, thanks to ICP DAS’s daughter boards, each board we have mentioned above is highly expandable.
We are good at I/O measurement. Just pick one, and let our board worry about the rest! The following are the product lists. Hurry to start your tour right away!
PCI-M512
PCI, 512 KB Memory Board with DI/O
PCI-M512U
Universal PCI, 512 KB Memory Board with DI/O
|
|
|
|
|
|
The new products in the PC-RSD-PCI Series are plugged each into a PCI bus slot on the PC to serve as a new type of silicon disk drive using a CompactFlash (CF) card in the same as a hard disk.
The PC-RSD-PCI Series has two CF card slots on the board, one of which comes standard with a CF card. The other slot is available between the PCI board brackets, allowing an additional CF card to be plugged and unplugged as a removable disk with the board installed on the PC. The second slot can extend the range of applications, such as separating the OS and data areas.
The PC-RSD-PCI board uses a highly reliable CF card (fixed disk mode), which can be partitioned into two or more drives. The PC-RSD-PCI board can also accommodate an optional additional CF card to add an additional drive or drives (thereby increasing the total capacity), in which case the two CF cards can be configured into a RAID by striping (RAID level 0), mirroring (RAID level 1), or spanning (JBOD) using a utility. The PC-RSD-PCI Series is a line of 1 GB, 2 GB, and high-capacity 4 GB and 8 GB models. These are designed environment-conscious to be lead-free and to (be scheduled to) conform to the RoHS Directive.
|
|
PCI Express BUS Serial Port Expansion
RocketPort EXPRESS serial cards are flexible, reliable, and high-speed in-server PCIe slot serial port expansion cards. They provide serial connectivity for applications like factory systems, SCADA systems, point-of-sale, telecommunications, medical systems and traffic equipment. Connect serial devices like printers, scanners, cameras, and LCD screens.
Highlights:
- PCI Express x1, x2, x4, x8, x12 and x16 Lane Connectivity
- Low-profile or Standard Height Compatible
- RS-232, RS-422, RS-845 Software-selectable
- 4 to 32-Port Interfaces
- High Performance Serial Cards with Speeds up to 921 Kbps
- RoHS Compliant
|
|
|
The Imaging Source - an international manufacturer of industrial cameras, video converters and frame grabbers announces today a new series of PCI-Express frame grabbers. The models ship with a number of different video inputs. Some models are available for low profile PC cases. The Imaging Source frame grabbers are deployed for applications in which analog video signals (PAL, CCIR, NTSC, RS-170) need to be processed by a PC. In addition to cameras, such video input devices include ultrasound and x-ray machines. Analog cameras are not only used in legacy applications. Often they are preferred for price sensitive projects, in which long cables are required. The Imaging Source frame grabbers ship with drivers for Windows, the SDK 'IC Imaging Control' and the end-user application software 'IC Capture'. The latter is a powerful software that allows the setting of all frame grabber parameters, the display of live video stream and the acquisition of singular images and sequences.
|
|
|
|
|
|
PCI Express Communication Interface netX for AS-Interface - COMBICON 2 pin
Fieldbus technology with it various standards is an established technology and will coexist for many years beside the upcoming Real-Time systems. With collected experience in fieldbus technology over the last 15 years and more than fifty thousands sold PC cards Hilscher introduces the next generation of cifX communication interfaces: They are based on the high sophisticated netX 100 network controller and differ from each other only in the physical interface. They provide the maximum of performance, functionality and flexibility for the best price-performance ratio. A ten-year commitment of availability is guaranteed using of the Hilscher own network controller.
The protocols for cifX are provided as loadable firmware on a CD. The driver loads the firmware into the cifX during each system start-up. This is a simple way to using the card either as master or as slave. A license is required for master firmware. The license can be purchased with the cifX or at later time and is remanently saved in the card.
|
|
|
Designed for requirements from 4 to 8 ports, these intelligent serial I/O adapters dramatically increase data throughput and enhance overall system response.
|
|
60 Megabit Per Second Synchronous Serial Interface
Features
* 1-4 or 16 channels
* 1-4 data bits per channel (4 channel), 1 clock and 1 data bit per channel (16 channel)
* ECL compatible driver/receivers
* Transfer rates up to 60 Megabits per second per channel
* Implements a high-speed DMA channel between an external device and PCIBus computer
* Customized by a Ram based programmable gate array
* Single short PCIBus slot
* Low cost
Description
The PCI GP-ECL board samples the data on the rising edge of the clock and stores it in host memory by the PCI GP-ECL DMA. It provides a simple, flexible low cost solution for Telemetry, Satellite and Monitoring applications.
In SSD4 mode, the PCI-GP-ECL provides a synchronous serial interface that can collect one to four channels and one to four data bits of synchronous serial data per channel. Transfer rates are up to 60 Megabits/sec.
Applications
* Telemetry Receiver
* Monitoring Serial Data Communications
* Satellite Ground Station Support
|
|
FAS-PCI Main Board
Selectable 64-point I/O to Input/Output/Latch
I/O main board using parallel direct connect type
Input/Output isolated by photocoupler
Slave module selectable Input/Output/Latch function
|
|
CANnes
Description
CAN-Bus PCI-Card with open source Linux driver
The CANnes card is a PCI card which provides a simple, easy to use CAN interface. It is equipped with a male and a female 9 pin Sub-D connector with standard CAN pin assignments. CAN bit rates between 10 and 1000 kBit/s (1MBit/s) are possible. The industry standard CAN controller SJA1000 is used together with the CAN bus driver 82C250 and optical isolation between the CAN controller and the CAN bus driver. A 120 ohms termination resistor is also provided. This resistor can be switched on and off either by a software controlled relay. Device drivers and function libraries are provided for the Windows (98/ME/2000 and NT4) operating systems and also for the Linux operating system. The CANnes cards is CE-approved and also meets FCC specifications. It can be used with every PC which is equipped with PCI slots fulfilling at least the PCI 2.1 standard.
|
|
|
|
|
|
- 24 channels of digital I/O with selectable 3.3 V and 5 V logic levels:
- 8-bit Port A, 8-bit Port B, 8-bit Port C (may be made up of 4-bit C-HI, and 4-bit C-LO)
- Fully plug and play
- Emulates 82C55 mode zero
- Software selectable pull-up and pull-down resistor configurations
- Digital I/O lines are accessed through a 37-pin D-type connector
The PCIe-DIO24 is a 24-channel digital I/O board with selectable 3.3 V or 5 V logic levels for PCI Express bus compatible computers. The 24 bits function as an 8-bit Port A, an 8-bit Port B, and an 8-bit Port C, which may be further divided into two 4-bit ports (Port C-HI and Port C-LO).
There is a 10 kilohm pull-up/pull-down resistor network associated with each digital port. Their direction is software selectable and stored on the board, so the user can use the board in a different PC without running configuration software: simply set the board number in InstaCal.
The PCIe-DIO24 is connector and software compatible with Measurement Computing's highly popular PCI-based PCI-DIO24 and ISA-based CIO-DIO24 boards, making migration from the ISA or PCI bus about as simple as unplugging the digital I/O cable’s 37-pin connector from the old board and plugging it into the new one. The PCIe-DIO24 is also supported by the same wide variety of external relay and solid state I/O module racks.
The PCIe-DIO24 is completely plug-and-play. There are no switches, or jumpers on the board. All board addresses, interrupt channels, etc. are set by your computer's plug-and-play software.
|
|
|
|
|
|
PCI334A Four-Port High Performance WAN Communications Adapter
Our PCI334A Intelligent Synchronous WAN Communications Adapter provides four high performance synchronous/serial channels for WAN connectivity. The adapter is ideally suited for use within SS7 nodes - or as an interface to T1 routers, DSU/CSUs, frame relay access devices, high speed modems or other high speed communication devices.
The PCI334A continues Performance Technologies' role as a leading supplier of hardware, software, system solutions and technologies for embedded applications.
Highlights
Multipurpose intelligent WAN communications adapter
Four high-speed channels capable of sustaining 2 Mbps per port
Four MB of shared SRAM memory
Universal I/O supporting 3.3V and 5V
Support for 33MHz and 66MHz PCI Bus
Increased RS-232 support allowing for data transmission range of up to 100Kbps
Existing PCI334 software compatible with PCI334A
Integrated WAN Communications Software includes Radar Receiver/SBSI, HDLC, Frame Relay, LAPD and X.25
Broad operating system support includes: Solaris®, Windows®NT and Linux®
|
|
|
|
|
|
High reliability and safety: Full opto-isolation!
This opto-isolated multiport datacom board is the all-rounder among the serial interfaces: Up to 8 ports, RS232, 422, 485 and mixed, rates up to 1 MBaud, additional discrete digital I/O lines and a counter. The ideal solution for your point-of-sales, retail or industrial datacom applications at a fair price.
Highlights
* ME-9000: Non isolation TTL ports.
* ME-9000i: Opto-isolated ports with common ground.
* ME-9000p: Opto-isolated ports with separate grounds.
Features
* 2, 4 or 8 ports.
* Optional breakout cable with 2, 4 or 8 connectors.
* RS232 or RS422/485 ports or mixed versions RS232 + RS422/485 (half of the ports are RS232, other half are RS422/485).
* High-speed transmission rates up to 1 MBaud.
* All handshake lines wired to the connector.
* Versions "i": Opto-isolation of all ports/lines with common ground (CGND).
* Versions "p": Complete opto-isolation of all ports with separate gounds (no
* common GND).
* ESD protection.
* Versions for 3.3 V and 5 V PCI.
* 8 discrete TTL digital I/O lines, 1 counter 16 bit.
* Ideal solution for POS (point-of-sales) and retail applications.
* For use with Windows NT, 2000, XP, Linux.
* PCI Local Bus 2.1 compatible. Plug'n'Play. Available as StandardPCI, PCI-Express or 3 U PXI/CompactPCI versions.
|
|
|
|
|
|
Models with opto-isolation!
This DAQ board series for professional applications offers a high level of flexibility. You will be surprised about the versatile functions the board offers. Starting with lowcost allround starter models up to highend versions with complete opto-isolation and lots of extra features - you will find the right board for nearly every standard DAQ application!
Highlights
* Models with opto-isolation.
* Models from low cost to high end.
* Open and expandable. Runs with Windows or Linux.
Features
* Up to 32 single-ended/16 differential analog inputs. Models "s": 8 single-ended input channels can also be used with simultaneous sampling. Ranges ±10 V, ±2.5 V, 0...+10 V, 0...+2.5 V.
* 16 bit/500 kHz A/D conversion (PCIe versions: 250 kHz; with ME-Synapse USB: 20...25 kHz). External digital and analog triggers.
* Models "i" A/D section opto-isolated.
* Up to 4 output channels. Range ±10 V. Models with one FIFO per channel.
* 16 bit/500 kHz D/A conversion. External digital trigger.
* Models "i" D/A section opto-isolated.
* 32 digital I/O channels, grouped in 4x 8 bit ports:
* ...Models without "i" TTL level, each port programmable as input or output.
* ...Models "i" 8 opto-inputs, 8 opto-outputs and 2x 8 TTL inputs/outputs.
* Models with timer controlled bitpattern output with FIFO.
* 3x 16 bit counters. Models without "i" TTL level, models "i" opto-isolated. All lines wired to the connector.
* PCI Local Bus 2.1 compatible. Plug'n'Play. Available for the bus platforms StandardPCI, PCI-Express or PXI-/CompactPCI and with ME-Synapse for Ethernet/LAN or USB.
|
|
|
|
|
|
Highlights
* A total of 48 digital channels: Opto and TTL I/O.
* High-drive for levels up to 32 V (optional up to 50 V). Load 700 mA.
* 2 USB versions: MEphisto Opto or combination with ME-Synapse.
Features
* ME-8200A (incl. MEphisto Opto A): 8 opto inputs and 8 opto outputs.
* ME-8200B (incl. MEphisto Opto B): 16 opto inputs and 16 opto outputs.
* Level up to 32 V (option: up to 50 V). Isolation up to 500 V. Outputs source, option "-S": Sink. Load up to 700 mA. Inputs with overvoltage protection/transient diode. Short circuit proof.
* 16 TTL digital I/O lines (2x 8 bit ports), expandable with relays/optoisolation.
* Can be used for monitoring of status changes, with interrupt.
* Bitpattern comparator, 1x or 2x 8 bit. Interrupt on comparison positive (not for MEphisto Opto).
* Interrupt on thermic load (not for MEphisto Opto).
* Any input selectable as interrupt source via mask register (not for MEphisto Opto).
* PCI Local Bus 2.1 compatible. Plug'n'Play. Available for bus platforms StandardPCI, PCI-Express or 3 U PXI/CompactPCI and with ME-Synapse for Ethernet/LAN or USB.
* USB version MEphisto Opto: USB 1.1 full-speed. Robust metal housing. External power supply.
* At the moment MEphisto Opto (USB) not with ME-iDS under Linux.
|
|
16 ports on one board!
This interface board gives you 16 full RS232 ports including all handshake lines. This high package of ports on a single PCI board is possible with two 68-pin VHDC connectors. Modern connectivity accessories convert the VHDC to standard 9-pin D-subs. The ME-9300 can reach transmission rates up to 1 MBaud.
Features
* 16 RS232 ports on a single PCI board.
* 8 ports connected to a high-densitiy VHDC connector.
* High-speed transmission rates up to 1 MBaud.
* All handshake lines wired to the connectors.
* ESD protection.
* For use with Windows NT, 2000, XP, Vista, 98/Me, Linux.
* PCI Local Bus 2.1 compatible StandardPCI version. Plug'n'Play.
|
|
|
|
|
|
DF PROFI II PCI/PCIe/CPCI/PC104+
High performance PROFIBUS DP/DPV1 interface
The DF PROFI II is a high performant PROFIBUS DP/DPV1 board of the newest generation and is available as PCI, PCIe, CompactPCI and PC104+ board. The DF PROFI II PCI interface supports 5V and 3.3V 32 Bit PCI slots, so it can be used in server pcs and workstations without problems. Beside the standard DP/DPV1 PROFIBUS services the board implements useful additional options.
The implemented hardware watchdog allows the electrical switch off of the PROFIBUS interface, that allows the board to be used in redundant DP Master concepts with 2 pc systems.
The process image contains except I/O data and status information a relative time stamp with millisecond resolution.
The DF PROFI II board needs for the data exchange of the process image only round about 1 ms with common I/O data sizes up to 3 Kbytes and stores the PROFIBUS configuration data in a failsafe flash memory.
For the compilation of the PROFIBUS configuration a very powerful and comfortable tool is available. The DF PROFI II board supports beside the popular operating systems Windows 2000/XP and Linux (SUSE, Redhat, Fedora) real-time operating systems like LINUX RT and LabVIEW RT.
|
|
|
|
|
|
All variations of digital I/O on one board!
This is the multi-channel alround model among the digital boards. Switch high loads and control digital statuses with a single board or box! Up to 48 relays, digital and opto channels for USB, PCI or PXI/CompactPCI.
Highlights
* A total of 48 digital channels: Relays, opto und TTL I/O.
* Switch currents up to 3.5 A.
* 2 USB versions: MEphisto Switch or combination with ME-Synapse.
Features
* 16 or 8 relays type C (change-over). For currents up to 2 A/30 V, short time/single relay up to 3.5 A.
* 8 TTL digital inputs (opto-isolated on versions "-O"). 16 TTL digital I/O channels, expandable with relays or opto-isolation.
* 8 opto-isolated inputs (24 level).
* 2 additional TTL interrupt inputs (not on USB version MEphisto Switch).
* PCI Local Bus 2.1 compatible. Plug'n'Play. Available for bus platforms StandardPCI, PCI-Express or 3 U PXI/CompactPCI and with ME-Synapse for Ethernet/LAN or USB. Also as MEphisto Switch for USB.
* USB version MEphisto Switch: USB 1.1 fullspeed. Robust metal housing. External power supply (included).
* At the moment MEphisto Switch (USB) not with ME-iDS under Linux.
|
|
|
|
|
|
The new products are low-profile, RS-232C serial communication boards compliant with PCI Express. The board can expand asynchronous RS-232C serial communication ports on a PC with a PCI Express compliant slot. The board is available in three models different in the number of on-board RS-232C serial communication ports: 1-channel type "COM-1C-LPE", 2-channel type "COM-2C-LPE", and 4-channel type "COM-4C-LPE".
The three new models support high-speed communication at up to 921,600 bps. The bundled driver software can be used for Windows and Linux to recognize the on-board ports as OS's standard COM ports, allowing them to be set as COM1 to COM256. The board has high-capacity FIFO buffer memory: 128-byte transmit buffer and 128-byte receive buffer. The FIFO buffer memory can be adjusted in buffer size for starting data transmission/reception. You can optimize the buffer size for each application, for example by increasing the buffer size to reduce the CPU load or decreasing it to improve realtimeness.
|
|
These new boards are compatible with L Series PCI board products and feature high-precision 16 bit analog input and output, digital I/O and a counter function. Other than their bus interface, these new boards share the same specifications as existing L series PCI products allowing applications to be easily transferred through hardware setting changes. External pin assignment and connectors are also the same allowing the user to use existing cabling.
|
|
This product is an interface board for PCI Express bus conformity which perform bidirectional input and output of a LVTTL level digital singnal. Input and output of 48 points at the maximum is possible with one piece. Choice is possible by applications software for the input or the output at a unit of eight points. By an attached driver library[API-PAC(W32)], it can make applications software for Windows in various programming languages that support Win32API functions such as Visual Basic or Visual C++.
|
|
This board is external equipment and an interface board of the PCI bus conformity which performs serial communication of RS-232C conformity.
It has the serial port of two channels by one sheet.
|
|
This board is external equipment and an interface board of the PCI bus conformity which performs serial communication of RS-422A/485 conformity.
It has the serial port of RS-422A/485 conformity of two channels by one sheet.
By using atta"
Moreover, COM-2PD(PCI)H can be replaced within the system already built for the higher rank compatible product of our company COM-2PD(PCI).
|
|
|
|
|
|
Overview
Moxa's CP-112UL/UL-I series of multiport serial boards are designed to be used by industrial automation system integrators for long distance, multi-point, PC-based data acquisition applications. On-chip Automatic Data Direction Control for precision RS-485 communications requires precise timing control for enabling and disabling the line driver. The Moxa Turbo Serial EngineTM chip that powers the CP-112UL/UL-I boards comes with on-chip ADDC®, which makes RS-485 as easy to use as RS-232. The boards come with 2 RS-422/485 serial ports, each of which can achieve data rates up to 921.6 Kbps. In RS-485 mode, the serial port can connect up to 31 daisy-chained RS-485 devices within a range of 1.2 km. For long distance RS-485 communication, 2 KV optical isolation protection is available to prevent equipment damage.
Support for Major Windows and Linux/Unix OS drivers
Moxa continues to support a wide variety of operating systems, and the CP-112UL/UL-I boards are no exception. Reliable Windows COM and Linux/Unix TTY drivers are provided for all Moxa boards, and other operating systems, such as WEPOS, are also supported for embedded integration.
Features:
Over 700 Kbps data throughput for top performance
128-byte FIFO and on-chip H/W, S/W flow control
Universal PCI compatible with 3.3/5 V PCI and PCI-X
Serial communication speed up to 921.6 Kbps
Drivers provided for Windows (2000, XP/2003/Vista/2008 x86/ x64), Linux 2.4, Linux 2.6 (x86/x64)
Easy maintenance with on-board LED display
On-board 15 KV ESD and 2 KV optical isolation protection
Wide temperature model available for -40 to 85°C environments
|
|
|
|
