{{product.productLabel}} {{product.model}}
{{#if product.featureValues}}{{product.productPrice.formattedPrice}} {{#if product.productPrice.priceType === "PRICE_RANGE" }} - {{product.productPrice.formattedPriceMax}} {{/if}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{product.productLabel}} {{product.model}}
{{#if product.featureValues}}{{product.productPrice.formattedPrice}} {{#if product.productPrice.priceType === "PRICE_RANGE" }} - {{product.productPrice.formattedPriceMax}} {{/if}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
Motion Controllers Series MC 3001 P V3.0, 4-Quadrant PWM with RS232 or CANopen interface Supply voltage: - 6 ... 30 V DC Max. continuous output current: - 1,4 A Peak current: ...
Motion Controllers Series MC 3001 B V3.0, 4-Quadrant PWM with RS232 or CANopen interface Supply voltage: - 6 ... 30 V DC Max. continuous output current: - 1 A Peak current: - ...
... important transfer station for signal collection and control signal output of EC100, EC160 and EC300 controllers. It consists of nine digital signal inputs, one analog voltage signal input, five relay ...
... solution for motion control and général automation. EtherCAT cycle min 125 m secs„ Bus coupler adopts EBUS technology to bring ail sub modules into EtherCAT network while maintaining stable performance. Flexslice ...
MC508 is a high spécification motion controller, which adopts arm cortex a9800mhz processor, has 8 voltage outputs and 8 flexible shaft interfaces, and can be configured as many as 16 puise direction ...
MC405 is a high spécification motion controller, which adopts high-performance arm 11 processor, has 5 flexible shaft interfaces and 4-way voltage output. PRODUCT INTRODUCTION: The MC405 has two différent ...
suitable for controlling valves with installed electronics for position and velocity control Design: Module for snapping onto carrier rails Enable input Cable break detection for actual value cable Short-circuit-proof interfaces Test ...
Bosch Rexroth - Industrial Hydraulics
... built-in power supply, and in various input / output configurations. Options for analog inputs and outputs, temperature sensor inputs, and temperature control. FX3 series analog intelligent function ...
... Connection via plug-in screw terminals Features • 2 individual servo channels • Analog inputs: Position transducer 0–10 V and pressure/force transducer ±25 mV • Analog outputs: ±10 V • ±100 • ...
The 2nd generation DVP-SX2 series slimline PLC has 14 digital I/Os and 12-bit built-in analog I/Os. It can be extended with DVP-S series left-side and right-side extension modules. Applications Used ...
Delta Electronics, Inc.
... feedback of motion control parameters, eliminating the communication bottlenecks of single-address, port based approaches. MAXv controllers use the PowerPC's message unit including ...
OMS Motion, Inc.
The PCIx is a PCI 4 axis motion controller that conforms to the PCI Rev. 2.2 specification. The PCIx is a four-axis controller for either servo or stepping motors. It supports 12 general ...
OMS Motion, Inc.
The PC78 is both a PC/104 controller that supports the PC/104 ISA bus standard as well as a stand-alone controller via a high speed RS-232 communication port. The PC78 supports up to 24 general purpose ...
OMS Motion, Inc.
... throughput and accuracy requirements. Working under any ACS SPiiPlus Platform EtherCAT master controller, the LCI tightly synchronizes control of a fixed beam laser with motion. Sub-microsecond latency ...
... system • Cycle time 1 ms • Commanding in Cartesian coordinates • Analog interfaces and motion stop optional Digital controller with EtherCAT fieldbus interface Digital controller ...
... powerful servo control and can be executed at up to 20 kHz. The Soloist drive-based, single-axis motion controller is part of the Soloist motion control platform.
... configuration • Digital inputs and outputs, analog input and output • Autozero function for holding current • Data recorder • Wave generator Digital motion controller for PIMag® ...
General Info. Centralized motion controller with built-in PLC functionality • 240V (+10% - 15%) power supply unit • EtherCAT bus coupler for up to 16x DI/DO modules or up to ...
The CTE 240 is designed with a multi functional system at intense standard. It can work up to 16axes control, PLC and graphic operator terminal. This tool also has a grounded on motorola µ processor to real 32 bit up ...
MINICLAMP (SHR) Analog braking module in Eurocard format for Minispeed systems, with 200W built-in resistance or 800W external resistance.
The PCIe-7856 is a PCI Express interface card providing two ports for Motionnet and HSL systems for distributed motion and I/O in machine automation applications. HSL technology allows thousands of I/O points to be scanned ...
IMAC VISUAL is leading the revolution in user-friendly motion control automation. With a drag-and-drop, visual blocks based programming, virtually anyone can program motion control ...
Please specify:
Help us improve:
remaining