... The Single Deck High Temperature Hydraulic Nut (HTHN) is capable of tensioning all of the studs on any valve, flange or cover simultaneously, loading 100% of the fasteners. This provides for complete elimination of distortion and ensures a perfect seal ...
... Used for clamping, pressing and bending. Ideal for welding and metal fabrication for fit-up of sheet or plate steel. Features In 5, 10, and 25 ton capacities. For use with Power Team general purpose single-acting series cylinders ...
SPX Hydraulic Technologies
... Operated Edge Clamp with Serrated Jaw - Left or Right Hand (WDS 216) (Available)£116.32 - £145.41 Each WDS 216 Type - Edge Clamps MATERIAL Steel, Case Hardened Chemical black finish LH = Left Hand Action RH ...
WDS Component Parts
... insures positive mechanical locking even if air pressure fails. Clamping arm opens 100°. Slotted open arm provides adjustable spindle location. 100 lbs holding capacity. Made in USA. This clamp is operated by a 3/4"-bore ...
CARR LANE MANUFACTURING CO.
Clamping force: 850, 1,000 N
... SDZ 40 F Used for clamping in component openings with expanding hooks and pulling mandrel. Very compact design, tensile force 1000 N, 10 mm clamping stroke. ...
TÜNKERS
... Mounting Kit. Cast aluminium clamp used to attach 25-50 mm diameter antenna mast or boom to 50 or 75 mm diameter mounting pipe. U-Bolts to attach to mounting pipe to be ordered separately (two required). ...
Clamping force: 20 kN - 100 kN
... sliding model using the press T-slot - variable clamping stroke (up to 8 - 12 mm depending on the model) - can be used on both the bolster and the ram - it can be fixed to provide fully automated clamping ...
SERAPID
Clamping force: 60 kN - 200 kN
... Torque 60–200 kN Description power clamping nut with bottomed thread thread protected centrical operation compact design Features integrated planetry gearbox for the multiplication of the manual tightening high temperature ...
ENEMAC
Length: 30 mm
... Product overview
EVO-KM30 is a two-piece
clamping module designed for modular two-column systems. It provides locating bores for precise positioning and permits retrofit installation on assembled systems. Precisely machined ...
Clamping force: 22, 40, 70 kN
... individually assembled with several clamping devices ✓ Clamping devices for automatic operation Large selection of GRESSEL hydraulic clamping devices Jaw width 65, 100, 125 and 160 mm Jaw adjustment ...
GRESSEL
... Bolt the clamp down to your worktable using the 3/8″ hole in the base. The 1/2″ copper plated Acme spindle resists weld spatter, and the swivel tip makes quick contact with your workpiece. Copper Plated Acme Screw / Ductile Iron Body Hold ...
Strong Hand Tools
... This is a description of assembling parts, including three different product parts and their related processing, testing, and assembly requirements. Here are explanations of each part and its requirements: M3 screw: The material of this part is 1008 ...
... reacts and makes a clamping cylinder in the clamp push against it. By this the contacting is established. A black push button is installed on the clamp to disconnect the contacting. It is no problem ...
Clamping force: 0 kN - 150 kN
... • side operation • low profile • with through-hole thread ...
JAKOB Antriebstechnik GmbH
... reinforced polyamide
BESSEY Tool GmbH & Co. KG
... sustainable workholding. With StampTEC, the rapid mould and die clamping system, you have all the convenience of magnetic strength at your service StampTEC is the magnetic system for quickly clamping moulds and dies ...
Tecnomagnete GmbH
The KB12-27 is a versatile tool that can be used horizontally, vertically, and even diagonally. When retracted, it can be stored in a pallet compartment to save space. Thanks to its wide adjustment range of 1.22 to 2.74 meters, it can be used in both ...
The fast-clamp driving dogs are used to pull the workpiece when it is fixed between two drills. They are highly useful in mass grinding processes. In fact, their high-speed opening and closing allows a significant reduction in the time necessary for changing ...
... Clamping equipment for coordinate measuring machines 3D-Flex-Fix The universal clamping system for the CMM provides the solution for your two most challenging requirements: 1. Unlimited clamping ...
Maprox AG
... For use in the printing cylinder of sheet-fed printing presses. Clamp ring made of higher strength steel sheet ensures a secure fit on the shaft. Punched part with a tolerance measurement on the front faces and spring support attached ...
... Application : Suitable for Food and Beverage, Pharmaceutical, Personal care, Pet Products, Dairy, Chemical, Breweries, Wineries & Distilleries Can be installed anywhere a traditional tri-clamp is used Features: Consistent, controlled compression of ...
... A clamping element is a non-positive shaft hub connection in mechanical engineering These elements connects a hub as sample with a gear shaft, so that a torque can be transmitted between the shaft and the hub. Furthermore, the hub is ...
... drill rod diameters from 25 - 209 mm BREAK-OUT / MAKE-UP torque 2.400 / 5.000 / 6.800 / 9.000 /18.800 / 32.000 Nm optimal force transmission through positive locking quickest break-OUT TOOL fulfils all common norms narrowest break-OUT ...
... The Girder Clamp is a critical fastener designed to securely hold onto structural members, such as crane frames or girders. This clamp provides a sturdy and reliable attachment point for lifting and moving heavy loads. The ...
... Multiflex vice - for clamping of multiple work pieces - each clamping element individually adjustable - with scale for ease of handling ...
... ensures two- sided acting lift and allows you to open and close the clamp quickly. Through the mounting holes the clamp kann mounted on a T-Slotplate or a thread grid plate. Pneumatik clamp PS-150-AL chuck ...
Stritzelberger GmbH
... EAS new Pressmag FP electro-permanent magnetic clamp systems are specifically designed to reduce changeover time for the metal forming industry. EAS Pressmag FP’s innovative design takes into account all of the operational characteristics ...
EAS change systems
Clamping force: 40 kN - 90 kN
... pressure die casting ■protected Trademark Multi Quick ■stepless vertically and horizontally adjustable ■strong clamping pressure for small clamping torque ...
Lenzkes Spanntechnik GmbH
... RECTANGULAR SECTION Material: Cast Iron FC300(JIS) / GG30(DIN) Heat treated: Normalized Application: Cast sections provide a fast & economical way to make special jig components. Features: Bushing & thread insert at every hole location, easily adapts ...
Leave Industrial
... you to clamp 1,000 different workpieces and gives you everything you need for complete machining. You need only one basic clamping device – a chuck or a stationary chuck that remains on the machine. For O.D., I.D., ...
... Speed and synchronization are easily adjusted when equipped with direct mount speed controllers. Air venting is QUICK with speed controller or air vent valve. Speed controller and air valve are for use with manifold (C type) hydraulic supply. ...
KOSMEK
Clamping force: 14,100, 14,250 N
... - Made of anodized aluminium - Swinging clamp to allow an easier up/down-loading of the slabs - Air fittings diameter can be chosen from the most common options - Quick up/down-loading - Quick air fittings - Stainless steel screws - ...
GNC Meccanica
... Automatic clamping takes place over disc springs, which are adjustable in the pre-loading and are solved pneumatically to the workpiece change. Manual clamping is made by a knurled knob on the opposite side of the ...
... The Hydrodock clamping system is used as the clamping system for the machine tool interfacing with changing processing units. For example, these include milling heads and attachment spindles. Once the processing unit ...
Berg & Co. GmbH Spanntechnik
... height. In this case stops shouldnt be mounted in the collet. Due to the self-locking device, compressed air is required for clamping and release. ...
Clamping force: 1.5 kN - 13 kN
... compensation system, these swing clamp cylinders maintain the clamping point with maximum precision over a long operating time. They can be equipped with clamp arm position control valves to ensure precise workpiece clamping. ...
HYDROBLOCK
Clamping force: 35, 100, 155, 225, 350 kN
... Mechanical clamp tensioner with rapid rise that is self-locking and vibration tested. Length is adapted for t-slot and tool flange. ...
AGAB Pressautomation AB
... hydraulic sliding clamps are integrated with a maximum clamping force of 80 kN, and are specially designed for minimizing down time when setting up or when it need to be frequently replaced. They are characterized by ...
... B TYPE (ALUMINUM ALLOY BODY) Product Description Model No. LD-30B / LD-40B / LD-50B Vertical and horizontal configuration. Applicable to BT, CAT, DIN tapers. ...
TORNG Industrial Co., Ltd.
Clamping force: 400 N - 5,000 N
... Pneumatic Clamping Element For rails : 15 to 65 mm Type: Closed without pressure Body in steel Operating temp. -20°C to 80°C Operation Pressure 5,5 to 8 bar ...
FLI - France Linéaire Industrie
the best suppliers