... Range PTFE Tubing is usually calling PTFE Pipe or PTFE Hose. PTFE Tubes are made of good quality PTFE,has best corrosion resistant and dielectricity. Description: PTFE Tubing is usually calling PTFE Pipe ...
... special discharge pipe in hot-dipped galvanized steel. The pipe hangs vertically down from the edge of the tank's inside, where it extends almost to the bottom of the tank to prevent splashing over ...
Inner diameter: 3 mm
Outer diameter: 5 mm - 140 mm
Delivered length: 1 m - 60 m
Outer diameter: 5 mm to 140 mm Inner diameter: From 3 mm Tube length: 1 mm to 60 mm Note: Small tubes, e.g. 3 mm OD, are typically less than 10 mm long
Inner diameter: 16 mm - 63 mm
Outer diameter: 20 mm - 72 mm
Pressure: 4 bar
TURBO MULTILAYER PIPE PE-RT multilayer pipe in bars, length 4 m.
... comparison to equivalent lagged lines. - Outer pipe remains a fixed length. All contraction is taken up in the inner pipe. Applications Vacuum insulated flexibles are based on a pipe in pipe ...
Inner diameter: 6, 10 mm
Outer diameter: 16, 13 mm
Injection hose consisting of a slightly-foamed PVC (PVC = polyvinyl chloride) with ribbed surface for better locking into concrete Suitable for grouting with microfine cement, acrylate gel and polyurethane resin Can ...
TPH Bausysteme GmbH
Product Name: Oil Tubing Produce Scope: +EUE seamless tubing,+NU seamless tubing,+IJ seamless tubing Standards: API spec 5CT, API spec 5B Specification Range: 2-3/8", 2-7/8", 3-1/2", 4", 4-1/2",WT: 4.24-16mm Materials: H40, J55, ...
ESP Cable Solutions Co.,Limited
Inner diameter: 406 mm - 1,420 mm
Outer diameter: 285 mm - 1,314 mm
... articulated pipe sections that can be adjusted hydraulically. Different soil conditions may require the use of special tools, such as a hammer system. Special initial augers guarantee optimal control behaviour. The ...
Inner diameter: 0.312, 0.25 in
Pressure: 200, 750 psi
Temperature: -20 °F - 190 °F
Air Hose Specifications (Low Pressure): - Textile Reinforced - Smooth Red Synthetic Rubber Casing - Oil Resistant Fluid Hose Specifications (Low Pressure): - Tube: Nylon 11 (Silicone-Free) - Braided ...
Inner diameter: 32 mm
Delivered length: 1 m - 2 m
... , so no glue is required for mounting. This makes for a sturdy and slim well pipe. The PVC pipe comes in different variations: Filter pipe PVC pipe with 0.3 mm vertical slits Note: ...
Inner diameter: 150 mm - 2,500 mm
... rubber-steel clad pipe included: run pipe, elbow, tee, reducer, U-channel etc. The pipe diameter is from DN150-DN2500, jointed by flange, the thickness of rubber liner is 3-40mm. We can also produce pressure-bearing ...
Pressure: 125, 200 psi
Uniweld's flexible Oxyfuel Hoses are color coded, have 8-sided crimp ferrules and are capable of withstanding high working pressures for reliability and long work life.
Inner diameter: 1 mm - 3 mm
Delivered length: 5 m - 15 m
The hose is the conveying line of the source extraction installation. The demands placed on the suction hose are: wear resistance low weight and flexibility not affected by extremes ...
Dustcontrol AB
Inner diameter: 14, 9.1, 4.6 mm
Pressure: 20, 15, 10 bar
The PFA Flow Tubes are available for the following models: Click Housing, Tubeholder, Clamp, and Clip Mounting. Characteristics High chemical resistance Wetted parts: PFA and ruby Available per 10-pack
Equflow BV
Inner diameter: 12 in
... venture used in ductwork are also fabricated from sheet. Many times the piping geometry does not allow full length of the Venturi Tube. In such case, ‘Truncated' classical Venturi Tube can be offered ...
Inner diameter: 8, 10 cm
Delivered length: 150, 200 cm
... , different lengths and sizes. Downpipe or gutter or descending pipe in cast iron with wall anchors. Used to drain roof water and protect the end of the copper, sheet metal or plastic pipe of the gutter
Outer diameter: 0.5 mm - 100 mm
Shell and Tubes are manufactured per customer needs and specifications, depending on the volume of liquids to be handled. Accurate temperature controls and energy efficient heating of the materials is essential. Shell and Tubes are usually ...
Inner diameter: 6 mm - 80 mm
Temperature: -220 °C - 550 °C
The pressure hoses from KLETTI form the basis of the heated hoses; in addition, they can be used in many other areas as cold hoses without heating and insulation. The hoses are resistant ...
Temperature: -40 °C - 200 °C
Calibration Hoses (also known as expansion or inversion bladders and inflation or cal tubes) are typically used in conjunction with open ended liners within CIPP (Cured-In-Place Pipe) rehabilitation and repair processes. ...
MEDIA SUPPLY In order to be able to operate an internal combustion engine or an electrified axle on a pallet system in a test bench, all connections must be connected first. We make sure that your test item is supplied with all ...
The air hoses MATISEC are designed both regarding raw material of the hose, nipple diameter and length in order to offer the minimum pressure drop. Each hose are controlled unitarily according connection ...
... Tubing | Pipe Availability: Custom order to your specifications Custom Sizes Available: Specify your diameter / length ratio and design configuration. Select CUSTOM Size option below. Please allow 3-5 weeks for custom ...
Inner diameter: 15.7 mm - 88.9 mm
... Model 400 Hydraulic Power Pack are designed to produce a variety of tube and pipe shapes, such as expansions, reductions, beads, flares, and other forms. The system utilizes hydraulic hoses ...
Outer diameter: 1 in - 14 in
Pressure: 5 bar - 42 bar
... petroleum, chemical industry, shipbuilding, agriculture, water conservancy, miners, fire fighting and other fields TPU LAY FLAT HOSE Structure: high-strength polyester or aramid braided layer, polyurethane inner and ...
Shenzhen Winan Industrial Development Co., Ltd.
Please specify:
Help us improve:
remaining