Process pumps

Pressure: 18.5 bar - 34.3 bar
Power: 224 kW - 1,275 kW

Drilling pump is also called mud pump, which transport high pressure, high specific gravity, high sand concentration drilling fluid to bottom of hole. Drilling fluid is used to cool bit, wash out bottom ...

Flow: 0 m³/h - 800 m³/h
Head: 1.5 m - 7.6 m
Power: 0.75 kW - 90 kW

... of the pump allowing return to service in minutes. Wide margin, easy passage of solids. Semi-open impeller. Possibility of installation at ground level, only with the suction pipe (the pump has to ...

Pressure: 0 Pa - 700,000 Pa

Port Size 3/8"(10mm) Maximum fluid discharge of 20L/min This compact light weight pump is a very popular model and can be used in a variety of applications often inside process machines. ...

Flow: 1.2 m³/h - 27 m³/h
Pressure: 8 bar
Head: 10 m - 40 m

Horizontal End Suction, Stainless Steel Pumps, compact design with closed impellers. Materials : SS304, SS316 Flange : BSP (F) Threaded Applications : Domestic Water Supply

Flow: 0 l/min - 3.4 l/min

Ideal for fluid transfer, dispensing, and metering applications in laboratory, process and wash-down environments Housings are completely sealed—IP66 and NEMA 4X rated Washdown drive is easy-to-clean and resistant to ...

Flow: 43 m³/h
Input diameter: 65 mm
Output diameter: 65 mm

... industrial pump (⌀ 65mm). Made in 316L Stainless Steel and ABS plastic, it is for example perfectly adapted for a use in wineries. Lowmotion 2.5 is washable and it is possible to disinfect it. Light and easy handling With ...

Flow: 0 m³/h - 4,000 m³/h
Pressure: 0 bar - 100 bar
Head: 0 m - 220 m

... abandon of mechanical seal pumps). Design features Pumps of the series CN MAG-M are horizontal single-stage volute casing pumps It is a modular configuration of either bare shaft ...

Flow: 1.2 us gal/min - 31 us gal/min

The stainless steel Enduro submersible pump is designed to exceed performance requirements in the most demanding applications. FEATURES • Utilizes an internal spring-loaded check valve design. • Pump ...

Flow: 130 us gal/min
Head: 1200'00"

Key features "APCO-CHEM" 150 series Pumps for Low Flow High Pressure Applications Lower Operating Costs than Standard Centrifugal Pumps at Low Flow Conditions Steep Head Capacity Curves for ...

Flow: 0.6 m³/h - 15 m³/h
Pressure: 70 bar - 120 bar
Power: 15 kW - 75 kW

High Pressure Plunger Pump The RONO high pressure plunger pump is a triplex piston pump and is used to convey various edible fat products through multipurpose process ...

Flow: 20 m³/h
Pressure: 5 bar

... temperature is not higher than 80%. LB series gear pump for freezer application： It can be used as a transmission and booster pump in the transmission process. It can be ...

Flow: 0 m³/h - 215 m³/h
Pressure: 0 bar - 48 bar

... minimise damage to shear sensitive products Pumps are available as monobloc or bareshaft Can be supplied with a Muncher, horizontally mounted onto the hopper, to assist solids reduction prior to pumping Pumps ...

Pressure: 0 bar - 25 bar

Paint pumps / Varnish pumps Gear pumps or Rotary lobe pumps Steimel pumps for paints and varnishes are used in machines and plants for the production ...

Flow: 0 m³/h - 900 m³/h
Pressure: 20 bar

MCP pumps can be installed in horizontal or vertical position. In warm box execution the pump can remain in cold standby and run in continuous duty. When supplied in cold box execution these pump ...

Flow: 280 m³/h - 2,333 m³/h
Head: 9.7 m - 128.7 m
Power: 450 kW - 800 kW

... according to the requirements of the customer. ZJ series slurry pump is a type of single-stage, single-suction, horizontal, cantilevered, centrifugal slurry pump. The ZJ series pumps ...

Flow: 2 m³/h - 280 m³/h
Pressure: 10 bar
Head: 2 m - 16 m

... head mounted, in - line type centrifugal pumps. • Formed by joining two standard INM series pumps with collector parts. • Special design composed of a common collector and integrated check valves at ...

Flow: 25 l/h - 576 l/h
Pressure: 5, 7, 10 bar
Power: 0.37 kW

GM mechanical diaphragm metering pump is LIGAO heavy-duty designed process pump for chemical dosing. It is reliable pump require minimal maintenance with high performance. ...

Flow: 0 m³/h - 300 m³/h
Head: 0 m - 150 m

... s Romak process pumps are used for handling various types of CLEAR & CLEAN chemical liquids with leak-free transportation. These pumps are manufactured to close tolerance and are of rigid ...

The RDC026 is a unit manufactured by RDC Rodicar company. It is a pneumatic pump high pressure applicable on various kinds of lubricants. For the installation process, the unit delivers different delivery ...

Flow: 2,000 m³/h

... Aturia has developed the submersible pumps for agricultural and municipality applications. These pumps are made out of grey cast iron as this material has a good resistance to rust. Back in the 1970’s ...

Flow: 400 m³/h
Pressure: 48 bar

The DHE series is is designed to pump products that are inherent to the oenological process. The unit is constructed either with a gear reducer, or with a worm gear reducer in a short version. The pump ...

Flow: 0 m³/h - 800 m³/h
Pressure: 10 bar
Head: 0 m - 35 m

single stage process centrifugal vertical immersion pump can be used for many applications in the industrial and marine markets. This vertical cantilever pump is designed to transfer ...

Flow: 2,500 m³/h
Pressure: 2.5, 5 MPa
Fluid temperature: -80 °C - 450 °C

... chemical process pump is a pump on the digestion and absorption of advanced domestic and foreign technology, based on the according to API610 (eighth edition) "heavy oil chemistry and ...

Flow: 0.5 l/min
Power: 35 W
Fluid temperature: 0 °C - 40 °C

... application process Powerful function and flexible configuration, make it easier to run multi-step complex programs. Applications： Suitable for laboratorial and industrial application Product Instruction： Automatic ...

Flow: 86.4 m³/h - 198 m³/h
Head: 9 m - 52 m
Power: 0 kW - 30 kW

... slurry pump is a type of centrifugal pump, designed for pumping liquid containing solid particles in mining, metallurgy,coal washing ,sewage water treatment,power plant,dredging.and chemical and petroleum industries ...