OverviewMost drilling failures are caused by site access rather than rock conditions. Crawler-mounted DTH drill rigs use tracked chassis to reduce ground pressure, improve traction on soft or uneven ground and climb gradients that wheeled rigs cannot. The YGS series includes five tracked models covering 3.8–8 T carriers and drilling diameters from 83 to 165 mm, sharing a common tracked chassis and YC-series diesel engines.
Key points- Tracks lower ground pressure and provide superior traction on mud, sand, loose spoil and uneven pads.
- Five models (YGS100A, YGS153, YGS180, YGS300, YGS350) match hole diameter, reach and site logistics.
- Supported hole diameters typically range 83–165 mm depending on model.
- Diesel tanks from 70 L to 225 L extend operating time between refuels.
- Designed for quarry blast holes, remote water wells, slope stabilization and micro‑piling.
Crawler DTH Drill Rig Specifications- YGS100A: Total weight 5.95 T; Walking speed 2.5 km/h; Diesel tank 85 L; Shipping size 6500×2100×2400 mm; Drilling diameter 90–146 mm; Power YCD4R22T-80; Max horizontal hole height 3.2 m.
- YGS153: Total weight 3.8 T; Walking speed 2.5 km/h; Diesel tank 70 L; Shipping size 4640×1980×2260 mm; Drilling diameter 83–130 mm; Power YC2108 33 kW/2400 rpm; Max horizontal hole height 2.8 m.
- YGS180: Total weight 6.3 T; Walking speed 2.5 km/h; Diesel tank 85 L; Shipping size 6600×2110×2500 mm; Drilling diameter 90–146 mm; Power YCD4R22T-80 55 kW; Max horizontal hole height 3.6 m.
- YGS300: Total weight 6.8 T; Walking speed 2.2 / 3.8 km/h; Diesel tank 85 L; Shipping size 6600×2220×2600 mm; Drilling diameter 90–152 mm; Power YC4DK80-T302; Max horizontal hole height 3.25 m.
- YGS350: Total weight 8 T; Walking speed 4 / 2 km/h; Diesel tank 225 L; Shipping size 7600×2350×2800 mm; Drilling diameter 90–165 mm; Power YC4DK100-T304 73.5 kW/2200 rpm; Max horizontal hole height 3.5 m.
Why a crawler-mounted DTH drilling rig beats wheeled units- Soft or wet ground: Wheeled rig — sinks, needs matting; Crawler — floats on wide tracks.
- Slope climbing: Wheeled rig — limited by traction; Crawler — grips and climbs.
- Ground pressure: Wheeled rig — high, concentrated; Crawler — low, spread over track length.
- Setup on rough ground: Wheeled rig — needs a level pad; Crawler — sets up on uneven ground.
- Road travel: Wheeled rig — faster on tarmac; Crawler — typically moved on a trailer for road transport.
Typical applications- Quarry benches: drilling blast holes on stepped faces where trucks cannot park level.
- Water wells in hilly or remote areas: reach village sites via rough tracks and during rainy seasons.
- Slope stabilization and micro‑piles: operate on gradients and soft shoulders where low ground pressure is required.
Representative case (summary)A highland granite quarry replaced a wheeled DTH rig with a YGS180 crawler. Bench-to-bench transfer time fell from 6 h to 2 h; monthly drilled meters increased from 1,800 m to 3,200 m; there was no rain‑season shutdown. Estimated payback ~9 months.
How to choose- Step 1 — Hole diameter: 83–130 mm → smaller models (e.g., YGS153); 146–165 mm → larger models (YGS300 or YGS350).
- Step 2 — Ground & access: soft, wet or sloped ground favors tracked carriers; hard flat pads may allow wheeled rigs.
- Step 3 — Horizontal reach: pick a model with sufficient max horizontal hole height for above‑track drilling (e.g., YGS180 for 3.6 m reach).
- Step 4 — Daily operating hours: larger tanks (e.g., 225 L on YGS350) reduce refuelling stops for long shifts.
Included with shipment (manufacturer note)Standard units are load‑tested before shipment and typically include an English manual, a spare seal kit and an operation video. Hammers, bits and compatible air compressors are available to complete the drilling package.