Product overviewThe Integrated DTH Drilling Equipment combines hammer, rig and air compressor on a single chassis. Built for quarrying, open-pit mining and construction, the integrated layout removes the need for a separate compressor trailer, simplifies site setup and supports effective penetration in hard rock conditions.
Key features- Power system: Yuchai diesel engine configurations provide consistent torque for hard rock drilling and controlled fuel consumption over extended shifts.
- Mobility: Crawler undercarriage for uneven ground; selected models offer multi-speed travel (example: YGS300 two-speed, YGS350 up to 4 km/h).
- Drilling control: Operator panel manages feed rate and rotation to adapt parameters to rock conditions and balance penetration with bit wear.
- Compact footprint: Smaller models fit tight quarry benches and confined urban sites.
- Stable alignment: Integrated design aligns hammer and hole to reduce deviation and improve hole straightness.
Applications- Quarry blast holes: limestone, granite, basalt for aggregate production.
- Opencast mining: production drilling for coal, copper, iron ore using large-hole models.
- Water well drilling: suitable for rural and agricultural boreholes and shallow well development.
- Geotechnical investigation: core sampling and site surveys where compact rigs are required.
- Road and railway construction: slope stabilization and foundation drilling with mobile models.
Real case exampleA YGS300 was deployed in a South African granite quarry. Compared with older equipment, the YGS300 increased penetration rates and reduced fuel consumption, enabling longer shifts and higher aggregate output with fewer breakdowns.
FAQ (selection)- Maximum hole depth: YGS series can handle depths up to ~30 meters depending on rock conditions; extended drill rod packages are available for deeper holes.
- Compressor requirement for YGS180: Typical compressors in the range of 10–15 m³/min at 7–10 bar are suitable; match to site and tool specifications for best results.
- Drilling angles: YGS units can drill vertical, horizontal and inclined holes; maximum horizontal heights vary by model.
Table: main model specifications (by column per model)Model: YGS100A | YGS153 | YGS180 | YGS300 | YGS350
Total weight: 5.95T | 3.8T | 6.3T | 6.8T | 8T
Walking speed: 2.5km/h | 2.5km/h | 2.5km/h | 2.2/3.8km/h | 4km/h 2km/h
Diesel tank capacity: 85L | 70L | 85L | 85L | 225L
Shipping size: 6500*2100*2400mm | 4640*1980*2260mm | 6600*2110*2500mm | 6600*2220*2600mm | 7600*2350*2800mm
Drilling hole diameter: 90-146mm | 83-130mm | 90-146mm | 90-152mm | 90-165mm
Power configuration: YCD4R22T-80 | YC2108 33kw/2400rpm | YCD4R22T-80 55kw | YC4DK80-T302 | YC4DK100-T304 73.5kw/2200rpm
Highest horizontal hole height: 3.2m | 2.8m | 3.6m | 3.25m | 3.5m
Technical specifications- Commercial name: Integrated DTH Drilling Equipment
- Available models: YGS100A, YGS153, YGS180, YGS300, YGS350
- Total weight (varies by model): from 3.8 T to 8 T
- Typical drilling hole diameters: 83 mm to 165 mm (model dependent)
- Walking speed (model dependent): single and multi-speed options (examples: 2.5 km/h; 2.2/3.8 km/h; up to 4 km/h)
- Diesel tank capacities (examples): 70 L, 85 L, up to 225 L
- Shipping footprints (examples): from ~4640×1980×2260 mm to ~7600×2350×2800 mm
- Power/engine options (examples): Yuchai engine families and specific outputs (examples on page include 33 kW, 55 kW, 73.5 kW depending on model)
- Applications: quarry blast holes, opencast mining, water well drilling, geotechnical investigation, road/railway construction
- Design: integrated hammer + rig + compressor (single-chassis), crawler undercarriage for site mobility