{{product.productLabel}} {{product.model}}
{{#if product.featureValues}}{{product.productPrice.formattedPrice}} {{#if product.productPrice.priceType === "PRICE_RANGE" }} - {{product.productPrice.formattedPriceMax}} {{/if}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{product.productLabel}} {{product.model}}
{{#if product.featureValues}}{{product.productPrice.formattedPrice}} {{#if product.productPrice.priceType === "PRICE_RANGE" }} - {{product.productPrice.formattedPriceMax}} {{/if}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
... low-viscosity, high-purity cyanoacrylate
adhesive. It is ideal for use on hard-to-bond plastics and rubbers such as natural rubber, EPDM and butyl rubber.
Cyanoacrylate
adhesives are single component
adhesives ...
Permabond
... frosting and fogging. Cyanoacrylate adhesives are single component adhesives that polymerize rapidly when pressed into a thin film between parts. The moisture adsorbed on the surface initiates the curing of the adhesive. ...
Permabond
Polymerization time: 5 s
... bondlines, common with other cyanoacrylate adhesives on hot and humid days, is eliminated. The elimination of fogging improves the production rate of acceptable parts as well as their appearance. The adhesive is very ...
Permabond
Working temperature: 120 °C
... paste which is slump-resistant (does not flow) during cure. The adhesive is toughened for maximum impact resistance, along with excellent peel and shear strength. ES550 is ideal for bonding a wide range of materials ...
Permabond
Working temperature: 120 °C
... paste which flows like solder when heated during curing. The adhesive is toughened for maximum impact resistance, along with excellent peel and shear strength. ES558 is ideal for bonding a wide range of materials including ...
Permabond
Gap fill: 0.5 mm
Viscosity: 10 Pa.s - 30 Pa.s
... surfaces being bonded. 5) Allow 24-36 hours for adhesive to fully cure. NB: Adhesive outside of a closed joint (i.e. excess material) will cure more slowly and may feel soft due to air contact. Adhesive ...
Permabond
Gap fill: 5 mm
Viscosity: 100 Pa.s
... is a 2-part, 2:1 low odour, acrylic adhesive. It was developed for structural bonding of nylon/polyamide without the need for any primers or additional surface treatment, such as plasma. TA4550 is also good for bonding ...
Permabond
... PERMABOND® UV605 is a very low viscosity, high strength adhesive which cures on exposure to UV light. Its excellent optical clarity and resistance to yellowing make it ideal for bonding glass and crystal for a high quality ...
Permabond
Working temperature: -50 °C - 150 °C
Packaging: 30, 500 ml
... Cyanoacrylate adhesive for special requirements | high viscosity | longer cure time | odourless and little to no blooming It is less susceptible to moisture effects after curing. WEICON Contact VA 1403 is suited for the clean and visually ...
WEICON
Working temperature: -55 °C - 140 °C
... climatic conditions. It is insensitive even under a longer influence of humidity. Contact VA 2500 HT is suitable for the bonding of the most diverse rubber materials and plastics and also for metal/plastic joints. VA 2500 HT can be used ...
WEICON
... Speed-Flex has an ISEGA certificate and can be used as an adhesive in the food technology. It is an adhesive and sealant based on MS polymer with extremely high initial strength and is suitable for the bonding ...
WEICON
Working temperature: -40 °C - 90 °C
... solvents. This adhesive and sealant is a strong 2-component system based on hybrid polymer, which enables full-surface bonding of larger parts and which can be used to fill gaps of up to ten millimetres. Flex 310 M® 2 ...
WEICON
... Product Description Hernon® Dissipator® 746 is a thermally conductive adhesive formulated for bonding electrical components to heat sinks or printed circuit boards. Fast room temperature cure combined with excellent ...