Bonding adhesives

... cyanoacrylate type adhesive. This high strength, rapid curing system is used primarily for medical device assembly. MB297Med is a higher viscosity (2,200-2,400 cps) cyanoacrylate. This kind of system, which is commonly ...

Two part, room temperature curing, thermally conductive silicone with ultra fine particle filler for bonding and smaller gap filling Key Features * High thermal conductivity * Very good electrical insulator * Low ...

Key Features - Low viscosity - Minimal shrinkage upon curing - Superb optical clarity - Cures at 80°C in shadowed out areas Master Bond UV22DC80-1 is a nanosilica filled, dual cure epoxy based system. It is formulated to cure readily ...

Gap fill: 5 mm
Working temperature: -40 °C - 80 °C
Shear strength: 21 daN

LOCTITE 3090 Instant Adhesive is a 2K, fast fixturing, gap-filling adhesive designed for assembling parts with varying bond gaps up to 5mm. LOCTITE 3090 Instant Adhesive is a 2K adhesive ...

Gap fill: 0.15 mm
Working temperature: -40 °C - 120 °C

LOCTITE 401 is a general purpose, fast curing, instant adhesive that is ideal for use on porous substrates. LOCTITE 401 is a fast curing instant adhesive designed for the assembly of difficult-to-bond ...

Gap fill: 0.15 mm
Working temperature: -40 °C - 135 °C

... medium viscosity, high temperature, durable, and fast-setting instant adhesive ideal for a wide range of substrates. LOCTITE 402 is an ultra-performing, fast-setting instant adhesive that provides reliable ...

Working temperature: -40 °C - 90 °C

... solvents. This adhesive and sealant is a strong 2-component system based on hybrid polymer, which enables full-surface bonding of larger parts and which can be used to fill gaps of up to ten millimetres. ...

Working temperature: -50 °C - 150 °C
Packaging: 30, 500 ml

Cyanoacrylate adhesive for special requirements | high viscosity | longer cure time | odourless and little to no blooming It is less susceptible to moisture effects after curing. WEICON Contact VA 1403 is suited for ...

Working temperature: -55 °C - 140 °C

... climatic conditions. It is insensitive even under a longer influence of humidity. Contact VA 2500 HT is suitable for the bonding of the most diverse rubber materials and plastics and also for metal/plastic joints. VA ...

... seconds for short cycle times in production • UV adhesive suitable for opaque materials • Suitable for a wide range of temperatures • Quick and reliable UV curing Please note: We supply hightech adhesives ...

... substrates • Optimum flow behavior for sealing and casting • Transparent dual cure adhesives available for large bonding areas Please note: We supply hightech adhesives exclusively ...

DELO-ML are one-component adhesives that contact to metal ions and also get cured under air exclusion. They are mainly used for sealing threads, securing screws and for bonding coaxial components. Moreover, ...

Working temperature: -55 °C - 150 °C
Shear strength: 11 N

... DeepMaterial multi-purpose UV curing adhesive product line covers the main applications of structural bonding. Under 365nm ultraviolet rays, it will be cured in a few seconds to form an impact-resistant ...

Working temperature: -55 °C - 150 °C
Shear strength: 8.6 N

... DeepMaterial multi-purpose UV curing adhesive product line covers the main applications of structural bonding. When exposed to 365nm ultraviolet rays, it will cure within a few seconds to form an ...

Working temperature: -55 °C - 150 °C
Shear strength: 16.8 N

... DeepMaterial multi-purpose UV curing adhesive product line covers the main applications of structural bonding. When exposed to 365nm ultraviolet rays, it will cure within a few seconds to form an impact-resistant ...

Working temperature: -60 °C - 340 °C

Kohesi Bond KB 1427 HT is a marvelous single component epoxy system for bonding, coating, sealing and casting applications. Although it requires a minimum temperature of 150°C for curing, it can achieve faster cures at ...

Working temperature: -70 °C - 180 °C

Kohesi Bond KB 1613 R80 is a single component epoxy system suitable for bonding, sealing, potting and encapsulation applications. Being a one component system, it does not require any mixing and offers an unlimited working ...

Working temperature: -70 °C - 200 °C

... to a wide variety of substrates including metals, ceramics, composites, most plastics and glass. It provides outstanding bonding and physical strength properties, as well as dimensional stability. TUF 1613 HT-CM is a ...

Working temperature: 180 °C - 200 °C
Polymerization time: 20 s - 40 s

... TRANSPARENT GRANULE GLUE FOR CARTON CLOSURE Glue in transparent granules in ethylene vinyl acetate copolymer (EVA). For gluing coated papers and board, and for applications where a long open time is ...

... APPLICATION EXAMPLES • bonding of aluminium corner angles into anodised or powder-coated cover- and wing frame • profiles for the aluminium window-, door- and façade manufacturing j• oint bonding of ...

... Aluminium window and door manufacturing for bonding of corner connectors. • Structural, force-locking bonding of the most varying material combinations, e.g. in the field of vehicle body manufacture. ...

Working temperature: -40 °C - 100 °C

... CHARACTERISTICS • Assembly bonding, general • Skirting, laying of laminate and cable ducts • Stair construction and building trade, general • Bonding of façades (cassette) ­ sandwich ...

Packaging: 50 ml

A cyanoacrylate adhesive. Characteristics: • Multifunctional cyanoacrylate adhesive • Ideal for bonding mirrors, glass, rubbers, metals and plastics • Instant adhesive • ...

Working temperature: -30 °C - 65 °C

... Hongkong Lead Time: 20 days Hold Fast stencil Spray Adhesive belongs to SBS all-purpose glue. It is suitable for bonding various light materials to themselves or other substrates. Spray adhesive ...

Working temperature: -30 °C - 65 °C

... Guangzhou,Shenzhen or Hongkong Lead Time：20 days Sprayidea 33 Insulation Spray Adhesive is specially designed for thermal insulation, HVAC industries. Perfect for bonding insulation materials such ...

Working temperature: 49, 30 °C

... Sprayidea Sponge Spray Adhesive 32 is a spray glue suitable for sponge materials, commonly used for bonding materials such as sponge, foam, latex, leather, fiber, fabric, wood, and metal. ...

Working temperature: 120 °C - 140 °C

Reactive one- and two-component systems are chemically curing adhesives and are liquid or pasty at room temperature. The Jowapur® series of Jowat provides a wide range of 1-C PU prepolymers with specific processing parameters, ...