|
|
Division profile
Systems to manufacture blown film have formed part of ALPINE's product range since 1955.
The reliability of these film blowing lines is well known, just as are the long years of experience we have had in the design and manufacture of such complex production equipment.
Our three testing centres - in Augsburg, USA and Japan - are equipped with state-of-the-art machines and components, and are used for both customer and development trials. Test series using the laboratory equipment can be carried out under as-real conditions so that the results fully reflect Alpine's capabilities.
Program Overview
Blown Film Lines
Extruder manufacturer
Film Die Heads
Film Cooling
Film Calibration
Film Take-off units
Film Winders
Film Orientation Lines
Process control
|
|
Manufacturers of extruders from 20 up to 150 mm
A full range of single screw extruders
• from 20 to 50 mm coextruders.
• from 20 to 50 mm extruders.
Taylor made Equipment
• Bi-metallic and nitrided screws and barells.
• Degazing system.
• Integration of electrical components used by the customer (standardisation)
• …
A wide area of application
• Pipes and profiles Extrusion and coextrusion.
• Thin Tubes for cosmetic packing
• Sheets and foils.
• Wire and tube coating.
• Pelletizing
• ....
|
|
The SATELLIS and HELLIOS series offers a wide range of single screw extruders manufacturers for the transformation of thermoplastics and rubbers, in different fields, such as:
- Production of tubes and profiles.
- Coating of wires and cables.
- Laboratory works.
- ...so.
YVROUD masters the design and the manufacturing of the machines which allow to offer a customised solution to all yours needs: do not hesitate to contact us on this point which is one of our strengths. |
|
Due to its versatility, flexibility, and high operational convenience the KAHL extruder is also appropriate for the production of extruded snacks. Thanks to its completely unproblematic starting and stopping behaviour, for example, the extruder type OEE 8 is the optimum machine for developing creative product designs and testing new formulae. Dies and final paddles
are changed within a few minutes. The waste of expensive raw materials is practically excluded by the unique hydraulic system which serves for fast opening and closing of the extruder with the die.
Fish feed
Floating or slowly sinking pellets can be produced for:
tilapia, carps, catfish. Very slowly sinking pellets for trouts, salmons, and perches. Or water-stable pellets for shrimps and other crustaceans. The production of extruded feed with a granular size of 0.1 - 2 mm is
possible, too.
Petfood
The production of high-quality petfood for dogs, cats, or zoo animals requires an optimum treatment of the mixtures during the fine grinding, pre-conditioning, extrusion, as well as coating processes.
|
|
An ever broadening spectrum of thermoplastics and applications calls for versatile processing solutions. Cincinnati Extrusion has developed the monos series of high-performance single-screw extruders for maximum performance, efficiency and melt homogeneity in the extrusion of smooth or corrugated PE and PP thermoplastic pipes.
This has been accomplished thanks to a new screw concept and the extension of the plasticizing unit to 37D. In addition, the series has been equipped with an innovative drive system.
Newly developed screws and power feed technology (PFT) provide an increase in the extruder%u2019s specific output.
The new plasticizing unit has proven effective in the production of corrugated pipes, where some dies tend to generate high back pressure.
In all models of the monos series, the motor is positioned underneath the feed zone which reduces the footprint, making it extremely short and slim.
monos extruders yield up to 40% higher output than their predecessor models with a maximum output of 1,300 kg/hr.
Cincinnati Extrusion offers several extruder lines for a wide range of applications.
|
|
Battenfeld Extrusionstechnik manufactures complete inline and out-of-line extrusion systems for Polyester (PET) film:
- film thicknesses of 100 µm - 1200 µm
- multi-layer and laminated film
- main applications are in food packaging
With Battenfeld Extrusionstechnik's specially designed co-rotating twin-screw manufacturer of extruders for A-PET film extrusion, non-pre-dried material can be run without problems.
Thus, processors benefit from:
- energy savings
- higher flexibility
- better film quality
|
|
Battenfeld Extrusionstechnik offers extruders manufacturers, extruder combinations and complete extrusion systems for corrugated PVC and Polyolefin pipes.
Main applications are:
- sewage water (high stiffness despite low weight)
- drainage (Polyolefins, very flexible)
- cable protection
- insulation
Battenfeld Extrusionstechnik cooperates with all well-known corrugator manufacturers.
Battenfeld Extrusionstechnik offers extruders, extruder combinations and complete extrusion systems for Polyolefin spiral wound pipes with diameters of 300 mm - 4000 mm.
Main applications are:
- sewage water
- drainage
- industrial air ducts |
|
Battenfeld Extrusionstechnik offers extrusion lines for fencing and complete plastic fence systems (posts, pickets, etc.).
PVC or WPC fencing profiles offer many advantages:
- low maintenance requirements and costs
- easy and inexpensive assembly
- easy to clean
Battenfeld Extrusionstechnik offers complete extrusion systems for plastic floor panels and other outdoor applications.
Major advantages of PVC or WPC floor panels:
- low maintenance requirements and costs
- easy and inexpensive assembly
- easy to clean
|
|
Battenfeld Extrusionstechnik manufactures tailor-made solutions for foam profile extrusion:
Main applications include:
- window sills
- outdoor floor panels
- shutter panels
- beads
- frames, etc.
Foam profiles are mainly characterised by their low specific weight.
If high surface finish is required, a layer of rigid PVC can be co-extruded
|
|
Battenfeld Extrusionstechnik offers co-extrusion equipment for the production of sewage water PVC foam core and multi-layer pipes with output rates of 50 kg/h - 1000 kg/h and pipe diameters of 32 mm - 630 mm.
Major advantages are:
- depending on the raw material / blend used and the pipe diameter, the
use of PVC multi-layer or foam core pipes yield in significant material
savings of up to 30% at a cost reduction of up to 25% compared to solid
pipes
- proven Battenfeld technology helps processors to take advantage of that
potential .
Battenfeld Extrusionstechnik offers complete extrusion systems for PP foam core pipes for sewage water transport for pipe diameters of 32 mm - 160 mm.
Battenfeld Extrusionstechnik offers a special compact 3-layer spiral mandrel die for the production of PP foam core pipes which can be operated with 2 or 3 extruders.
Major advantages:
- significant weight reduction compared to solid pipes
- recycled material can be used for the inner layer
|
|
Battenfeld Extrusionstechnik manufactures custom-made extrusion machines as well as the miniBEX standardized line for the production of technical profiles.
Major applications include:
- edge bands for the furniture industry
- industrial scanner profiles
- high-precision profiles, IC tubes, etc.
Main features and benefits of miniBEX lines:
Plug&play-line with standardized and perfectly matching line components, consisting of:
- different industrial extruder sizes with output rates of up to 130 kg/h PVC
- all processing units can be utilized without further line modifications
- calibrating table, 4 m or 6 m long
- caterpillar or belt haul-off
- industrial saw or knife cutting device
- also available as twin-strand version
- short delivery times
- excellent price-performance ratio |
|
In cooperation with experienced partners, Battenfeld Extrusionstechnik manufactures complete extrusion equipment for PE and PP drip irrigation pipes.
Pipes with diameters of 16 to 50 mm can be fabricated with our lines.
Main line characteristics:
- line speed: up to 80 m/min
- insertion of up to 250 drippers per minute
- dripper capacity: 2, 4 or 8 l/h
- number of dripper holes: 2 or 4
- fully-automatic perforating device
- dripper type: pressure-compensating and
non-pressure-compensating
- up to 80% reduction in water usage can be achieved
|
|
Battenfeld Extrusionstechnik manufactures complete extrusion devices for the production of Polyolefin multi-layer industrial pipes with diameters of 10 mm - 63 mm
for the following applications:
- potable water transport
- hot water transport
- floor heating/radiators
- industrial applications.
Pipe with specific attributes, e.g. acoustic insulation, oxygen barrier, special optical, mechanical or thermal properties can be economically manufactured with extrusion lines from Battenfeld Extrusionstechnik.
Battenfeld's special side-fed dies for multi-layer pipe offer the following advantages:
- gentle processing of material highly sensitive to thermal and mechanical stress, even at low mass flow rates
- symmetrical distribution of pressure in the die through twin center sleeves preceded by a coathanger manifold
- thermal isolation of each individual layer of melt through the modular, consecutive connection of several distributors
- optimum melt homogeneity due to a brake-up plate located behind the side-fed distributor
- accurate wall thickness distribution
|
|
Battenfeld Extrusionstechnik manufactures complete extrusion equipment for
PE-Xb and PE-Xc pipes for pipe diameters of 12 mm - 160 mm.
Main applications include pipe for:
- potable water transport
- hot water transport
- floor heating/radiators
- gas transport
- industrial applications, e.g. pressurized air.
Major characteristics of cross-linked Polyethylen:
- Highly increases the thermal and mechanical properties of a flexible
Polyethylen pipe
Major advantages are shorter assembly times and the laging (embedding) of pipes regardless of heat expansion.
|
|
Battenfeld Extrusionstechnik offers complete extrusion systems for aluminium composite industrial pipes for pipe diameters of 14 mm - 110 mm.
Major applications include:
- potable water transport
- hot water transport
- floor heating/radiators
- gas transport
- pressurized air.
Main characteristics of alu-composite pipe:
- aluminium composite pipes consist of 3 layers of plastic/aluminium/plastic, e.g. PE-X/Alu/PE-X
- Battenfeld Extrusionstechnik cooperates with TEMPLET Deutschland GmbH, a leading manufacturer in the field of aluminium forming and brazing
Major advantages of Battenfeld extrusion machines:
- high line speed of over 50 m/min
- all processing steps optimally harmonized |
|
Battenfeld extruding technology supplies complete extruding lines and automatic control engineering for the production from mono and multi-laminated industrial plastic plates to the subsequent treatment in the deep-drawing and as semi-finished material for technical applications:
- Disk thicknesses from 1 mm to >20 mm
- Materials: HP, PP, PE, ABS, SAN
Battenfeld extruding technology successfully supplies plants for many years to the extruding of plates for the following applications:
- Industrial refrigerator plates
- Applications of sanitary, e.g. Bath tubs and shower cubicles
- Automobile industry
- Chemical industry
- Furniture industry
|
|
Battenfeld Extrusionstechnik manufactures single-screw extruders manufacturer with or without degassing screws and with smooth or grooved feed bush feeding zone as well as complete extrusion machines for pelletizing PE, PET, PP, PS, PA, PC and ABS.
- output rates of single-screw extruders: up to 1500 kg/h
Benefits of Battenfeld single-screw extruders:
- high specific output rates
- excellent dispersing and plasticizing performance
- extruder execution adapted to material processed:
- grooved-feed or smooth feeding zone
- barrier or multi-zone screws
- with or without degassing screws
Can be combined with strand, under-water or water ring pelletizing units
automatic process driver with BMCplus.
|
|
Battenfeld Extrusionstechnik is your reliable partner for complete extrusion lines for PE and PP plastic tubing with output rates of 50 kg/h - 2500 kg/h
and pipe diameters of 10 mm - 2000 mm.
Major applications include:
- potable water
- sewage water
- gas
- cable protection
Production systems for PO pipes manufactured by Battenfeld Extrusionstechnik offer processors many advantages.
High output rates through:
- direct-driven extruders
- barrier screws
- wear-resistant stellite screw flights
- bimetallic barrels
Lattice basket dies for:
- low pressure build-up
- even melt distribution
- wide processing window
- excellent wall thickness control
- fast color change
- especially suited also for multi-layer pipes
|
|
Battenfeld Extrusionstechnik manufactures complete manufacturers of extrusion lines and automation systems for mono- and multi-layer plastic sheet to be further processed or as semi-finished products for technical applications:
- sheet thickness of 1 mm to >20 mm
- raw material: PS, PP, PE, ABS, SAN
Since many years, Battenfeld Extrusionstechnik successfully delivers sheet extrusion lines for the following applications:
- industrial refrigerator housings
- bath tubs, shower cabins, etc.
- automotive products
- products used in the chemical industry
- furniture products
|
|
Battenfeld Extrusionstechnik manufactures extruders manufacturers and complete extrusion devices for pelletizing.
output rates two-stage planetary roller extruder:
- up to 3600 kg/h (rigid PVC)
- up to 4000 kg/h (soft PVC)
output rates twin-screw extruder with EMS:
- up to 1400 kg/h (rigid PVC)
- up to 2000 kg/h (soft PVC)
Benefits of the two-stage planetary roller extruders:
- wide processing window through excellent dispersing and plasticizing performance
- thermally-sensitive compounding of material through
- low-friction plasticizing system
- internal temperature control of main suppliers of spindle
- gentle material compounding due to very short
- residence time in the system
- automatic process control with BMCplus
Benefits of the twin-screw extruders with EMS:
- electromotive shear gap adjustment dependant on material used
- wide range of screw speed (low-high shear)
- effective temperature control of barrel and screw
- air cooled barrel and internal screw temperature control
- adapted screw design for higher filled material
- automatic process control with BMCplus |
|
Battenfeld Extrusionstechnik is a leading supplier of complete extrusion systems for the production of PVC pipes with output rates of 50 kg/h - 1500 kg/h and pipe diameters of 10 mm - 1200 mm.
Major applications include:
- potable water
- hot water (C-PVC)
- sewage water
- cable protection
Production systems for PVC pipes made by Battenfeld Extrusionstechnik offer professional processors decisive advantages:
- small footprint due to compact extruder manufacturer design
- maintenance-free screw temperature control
- optimum screw wear resistance
Our PVC double spider dies offer the following advantages:
- low pressure build-up
- higher volume within the die
- higher throughput
- no continuous spider marks
|
|
Battenfeld Extrusionstechnik offers complete extrusion systems for siding / wall cladding applications.
Major advantages of PVC or WPC siding profiles include:
- low maintenance requirements and costs
- easy and inexpensive assembly
- easy to clean
|
|
Battenfeld Extrusionstechnik is a leading supplier of inline and out-of-line extrusion systems which are also available as high-performance lines:
- mono- and multi-layer deep drawn PP, PS or PET film up to 7 layers
- film thicknesses of 200 µm - 2 mm
- main applications in food packaging, esp. packaging of dairy products
inline extrusion systems can be combined with all automatic thermoforming machines currently on the market.
Battenfeld Extrusionstechnik offers a specially tailored line of manufacturer of extruders for the production of deep drawn films/sheet that enables processors to run their own production process very efficiently.
- high specific output rates
- degassing extruders for optimum melt quality
- constant mass throughput and therefore excellent thickness tolerances through the use of melt pumps
- state-of-the-art flat dies adapted to end product
- raw material savings and recycled material can be used without problems
low energy consumption
- modern, compact, maintenance-free drive technology for main- and co-extruder
For the production of thermoforming films/sheet, Battenfeld Extrusionstechnik manufactures especially tailored roll stacks that ensure superior end product quality.
|
|
|
|
Injection molding machines, Extruders
