|
|
ASTRO stepping motor SAM
- different designs
- permanent magnet-excites
- gradual or continuous enterprise
- high modulation rates
- Precision in the stepper angle
- short starting and stop times
- noiseless run
- high self retaining moment
- sturdily, reliably, long-lived
- Maintenance-free
Stepping motors SAM
2-Phasen
Torque = 3 - 1020 Ncm
Mode of operation = bipolar
Stepper angle = 4-polig for stepper angles of 45°
Full to mini step
Translation with transmission = minute to second step
Self retaining moment = in the dead condition
max. coil temperature = 130°C
Wärmeklasse B
Enclosure = IP40
Braid and terminal box connection
Hybrid stepping motors SAM
2-Phasen
Torques = to 26 Ncm
max. coil temperature = 120°C
Enclosure = IP30
|
|
Stepping motor frame sizes NEMA17,23 and 34
Standard and high torque types.
Motors with:
- Planetary Gear Box
- Terminal Box
- Connectors
- Encoder
- Brake
- Special Winding
etc. upon request
|
|
Stepping Motors are motors which can be directly controlled by digital signals and rotate at constant angles according
to a pulse signal. These motors specified by EC Motion have been used in various application to control angle, speed
and position. A full line of various models is available with superior features, excellent torque characteristics and high
reliability in order to meet the requirements of your specific application.
our 2-Phase-Step Motors have following sizes:
20mm, 28mm, 35mm, 39mm, 42mm, 56.4mm, 60mm and 86mm.
Full Step Angle from: 1,8°, 0,9° and 0,45°
Holding torque from: 0,017 Nm up to 10,2 Nm
all Step Motors are available with Single-Shaft (A or AE) and Double-Shaft (B or BE). The Step Motors Series SECM26... and SECM29... are also available with Terminal Box.
other designs are:
- Step Motor with Planetary Gear
- Step Motor with Encoder
- Step Motor with electromagnetic Brake
to drive our Step Motors you can use our Driver-Series SMD-Series and ECMD-Series
|
|
HAYDON rotary motors are built to provide exceptionally high torque-to-size ratios. By utilizing a patended enlarged rotor with low inductance coils, the motors provide superior torque and continuous, reliable high performance.
HAYDON rotary motors come in a variety of sizes ranging from 20 mm to 56 mm. Optional rare earth magnets may be specified for even higher torque.
Pancake Motors and Planetary Gear Train Motors are also produced by Haydon for high torque requirement.
Some typical applications for HAYDON rotary motors include medical equipment, bar code scanning devices, printing equipment, laboratory instrumentation and other high torque, small space mechanisms.
|
|
|
The 1.8º NEMA 34 High Torque Motor is available in 2.6”, 3.77” and 5.0” lengths. The motors are capable of holding torque from 310 to 920 oz-in based on unipolar ratings. Unipolar and bipolar windings are available to allow for torque and speed to accommodate your application. The high torque motor provides approximately two times more holding torque than a standard motor of similar design. The size 34 motor can provide high step accuracy as well as high resolution.
|
|
2 Phase stepper motor
Mounting size: 56.4mm, 85mm
Maximum holding torque: up to 9.3Nm
Basic step angle: 1.8°
Protection class: IP65
Marking: CE
2 Phase stepper motor - Cable type
Mounting size: 56.4mm, 85mm
Maximum holding torque: up to 6.6Nm
Basic step angle: 1.8°
Protection class: IP54
Marking: 56.4mm:UL/CE, 85mm: CE
|
|
CMK Series 2-Phase Microstepping Motors
The CMK Series is a motor and driver package consisting of a 2-phase stepping motor and one of the smallest, lightest 24 VDC input microstepping drivers in the industry, allowing for a reduction in size and vibration in your equipment. High-torque, high-resolution, geared and standard type motors available.
- 24 VDC input driver
- Wide variety of compatible motors
- 1.10 in. to 2.36 in. frame sizes
- Maximum holding torque from 0.44 lb-in to 35 lb-in
- Permissible speed range from 0 to 4500 r/min
- Microstep resolution to 3,200 Step/Rev (1.8° Motor)
- RoHS compliant
|
|
3-phase stepping NEMA34 size (90mm)
High Torque
Standard motor with terminal box
Earth ground connection terminal inside the terminal box
Motor versions also available with:
- Planetary Gear Box
- Leads
- Connector
- Encoder
- Break
- Special winding
etc. upon request
|
|
Schneider Electric Motion 3-phase stepper motors are extremely robust and maintenance-free. They carry out precise, incremental movements as controlled by a stepper motor drive. A stepper motor drive system consists of a stepper motor and a matching stepper motor drive. Maximum performance of the complete drive system requires the motor and the drive to be perfectly adapted to each other. Depending on the stepper motor drive, the motors can be operated at very high resolutions.
A complete range of options such as rotation monitoring and holding brake as well as robust planetary gearboxes with very little backlash extends the application range.
Schneider Electric Motion 3-phase stepper motors are available in standard and Ex versions (EEx d IIC T4).
|
|
|
|
|
|
Stepper drives and stepper motors for motion control
Description
Truly Simple
Forget about encoder systems and commissioning software
A compact drive and a high-accuracy motor included in the package
Reference values are preset and monitored by a higher-level PLC or a Schneider Electric motion controller
3-phase stepper motors stand for precision, power and sturdiness
In most cases a gearbox is not required due to the high torque
Extremely Compact
The Lexium SD3 require very little space in the control cabinet
Compact dimensions (H x W x D: 145 mm x 72 mm x 140 mm)
The price is as compact as its dimensions
High Flexibility
Two different power classes, different interfaces and numerous other options and accessories
Available up to 6.8 A
Suitable for mains supply with 1-115 VAC and 230 VAC (50/60 Hz)
Feature a 5 V and a 24 V pulse/direction interface or fieldbus interfaces (CANopen, CANopen Motionbus and Modbus or Profibus DP)
SD3 also available with rotation monitoring (SD3 28 has it on board)
Integrated safety
Safe Torque Off functionality prevents unintended machine starts as per IEC/EN 61800-5-2 for operator safety
The connection to the positioning electronics is retained even when the Safe Torque Off function is active. Re-homing is not necessary
|
|
Stepping Motors are motors which can be directly controlled by digital signals and rotate at constant angles according
to a pulse signal. These motors specified by EC Motion have been used in various application to control angle, speed
and position. A full line of various models is available with superior features, excellent torque characteristics and high
reliability in order to meet the requirements of your specific application.
our 5-Phase-Step Motors have following sizes: 60mm and 86mm.
Full Step Angle from: 0,72°
Holding torque from: 0,42 Nm up to 6,3 Nm
all Step Motors are available with Single-Shaft (A) and Double-Shaft (B).
other designs are:
- Step Motor with Planetary Gear
- Step Motor with Encoder
to drive our Step Motors you can use our Driver-Series SMD-Series
|
|
CFK II Series Stepping Motors
Offering high performance and simple operation in a compact size, the 5-phase CFK II series microstepping driver and motor package is available in both standard and high speed versions. The CFK II series provides unparalleled resolution and low vibration in an open loop system, as well as high torque in the high speed range.
- DC input
- Frame sizes from 0.79 in to 3.35 in
- Maximum holding torque from 0.2 lb-in to 55.63 lb-in
- Permissible speed range from 0 to 4500 r/min
|
|
CRK Series, 5-phase with microstep with built-in controller
Power supply: 24 V DC
Marking: CE
With microstep driver.
Standard type
Mounting size: 42 mm and 60 mm
Max. permissible torque: up to 1.66 Nm
Geared types:
Taper hobbed gear:
Mounting size: 42 mm and 60 mm
Max. holding torque up to 4 Nm
Permissible torque 0.35 Nm - 4 Nm
Backlash 0.25° - 0.75°
5 gear ratios of 1:3.6 - 1:30.
|
|
Power supply: 24 V DC
Marking: CE, cUL
With microstep driver.
Standard type
Mounting size: 42 mm and 60 mm
Max. permissible torque: up to 1.66 Nm
High-Torque type
Mounting size: 20, 28 and 42 mm
Max. permissible torque: up to 0.42 Nm
High-Resolution type
Mounting size: 28, 42 and 60 mm
Max. permissible torque: up to 2.3 Nm
Geared types:
Taper hobbed gear: max. holding torque up to 4 Nm, permissible torque 0.2 Nm - 4 Nm, backlash 0.167° - 1°, 5 gear ratios of 1:3.6 - 1:30.
Planetary gear: max. holding torque up to 8 Nm, permissible torque 0.2 Nm - 8 Nm, backlash 0.034° - 0.58°, 6 gear ratios of 1:5 - 1:50.
Harmonic gear: max. holding torque up to 8 Nm, permissible torque 3.5 Nm - 8 Nm, 2 gear ratios of 1:50 and 1:100.
|
|
PMC Series Stepping Motors
The PMC series combines a high torque miniature 5-phase stepping motor with a board-level, credit card sized driver.
- DC input
- 1.10 in frame size
- Maximum holding torque from 0.3 lb-in to 17.5 lb-in
- Permissible speed range from 0 to 2500 r/min
|
|
Key Attributes and Characteristics:
- Frame sizes ranging from 15mm to 60mm
- Output speed up to 750 rpm
- Windings can be designed for optimum performance
- Long life lubrication
- Simple mechanical construction with proven design characteristics
- Unipolar or Bipolar windings
- High torque size ratio
Advantages:
- Low cost construction
- Ease of use in application
- Simple open loop positioning
- Customization to meet application demands, including shaft, bearings, connectors, and sub-assembly
|
|
The Ezi-SERVO is an Innovative closed loop stepping motor control system that utilized a high-resolution encoder.
The Ezi-SERVO keeps updating the current position every 25 mico-sec using high performance DSP.
The most suitable to Vision System.
|
|
AS Series IP65 Rated Closed Loop Stepping Motors
The AlphaStep is a revolutionary hybrid stepping motor and driver package which eliminates missed steps. The AlphaStep uses a built-in feedback device that constantly monitors the motor shaft position to detect and correct for loss of synchronism.
- IP65 rated motors for dust/water-proof performance
- AC Input
- 2.36 in and 3.35 in frame sizes
- Maximum holding torque from 10.6 lb-in to 35 lb-in
- Permissible speed range from 0 to 4000 r/min
- RoHS compliant
|
|
STANDARD RANGE OF STEPPING MOTORS + ENCODERS :
- Hybrid steppers 2-Phase & 5-Phase, 0,9° and 1,8°
- Mounting size : 42mm to 60mm
- Holding torque : 0,26Nm to 2,1Nm
- Incremental Optical Encoders
- UL/CSA/CE and ROHS compliant
CUSTOMIZATION :
gear box, screw, hollow shaft...
|
|
|
ElectroCraft TorquePower and TorquePower Plus motor have set the standard for quality, reliability, and durability in stepping motors. With non-cumulative position accuracies as low as ±3%, the precision of our TorquePower motor is matched only by the dependability of its performance. Our TorquePower motors are also bi-directional and totally enclosed with permanently lubricated ball bearings for long-lasting, smooth operation.
|
|
Extremely high speed performance unlike other standard stepper types
Extremely low current consumption
Extremely light and compact
Digital control for simple system integration
Smooth and accurate speed control
High/low temperature operation
Operation in a vacuum
Electronic commutation for extremely long operational lifetime
High precision gearboxes available in all sizes
Feedback components available in all sizes
Control electronics available for all motor series
Custom systems available from design to production
1 and 2 phase stepper motors available
|
|
- 2-phase DC stepper motors, torque range 0.24 to 1.6 Nm
- Step angle: 1.8°
- Rated supply voltage: 24 ... 60 V
- appropriate stepper motor amplifier: ECOSTEP54 for 4 motors
- Microstep control (12.800 microsteps) for a high positioning accuracy and a
smooth motor running
- Switching from sine to rectangular commutation depending on the speed
- 8 isolated digital inputs and outputs
- Parameterization via CANopen or RS232
|
|
saia rotary stepper motor
Dimensions (mm) from Ø 13x36
Step angle (°) 18
Holding torque (mNm) 2.0
Detent torque (mNm) 0.3
Winding bipolar
|
|
2 phase types
Standard type: mounting size 42mm - 85mm, max. holding torque up to 9.3Nm, basic step angle 1.8°.
High Resolution type: mounting size 42mm - 56mm, max. holding torque up to 1.35Nm, basic step angle 0.9°.
Gearhead type: mounting size 28mm - 90mm, max. holding torque up to 12Nm, basic step angle 1.8°.
P-type: mounting size 28mm - 42mm, max. holding torque up to 0.93Nm, basic step angle 1.8°.
J-type: mounting size 60mm, max. holding torque up to 3.1Nm, basic step angle 1.8°.
With encoder:
mounting size: 42mm, 56.4mm, max. holding torque up to 9,3Nm, basic step angle 1.8°.
High-Efficiency Type:
mounting size: 42mm, max. holding torque up to 0,55Nm, basic step angle 1.8°.
5 phase types
Mounting size: 42mm - 85mm
Max. permissible torque: up to 6.3Nm
Basic step angle: 0.72°
|
|
|
|
|
|
Gemini GT Microstepping Drive
Provides two power ranges for up to 8 Amps of continuous current
Step and direction (cw/ccw)mode
Active Damping%u2122, Electronic Viscosity%u2122, and ABS Damping%u2122
Encoderless stall detect
Simplified configuration
Short curcuit protection - phase-to-phase and phase-to-ground
OEMZL Microstepping Drive
4 Amp or 6 Amp @ 120 VAC (170 VDC bus voltage)
Standard step-and-direction input or CW/CCW input
Operates with standard 1.8" hybrid step motors
Anti-resonance eliminates mid-range instability and provides damping ratios of up to 0.2
CE marked for LVD compliance
UL recognized
E-AC and E-DC Microstepping Drives
AC: Designed for use with motor inductance of 0.5 mH - 80 mH AC / 0.2 mH-80 mH DC
3-state current control allows the drive and motor to run cooler and more efficiently than 2-state drives
Selectable resolution up to 50,800 steps/rev
Auto standby reduces motor current (and heating) at rest
Provides 0.02 Amps to 3.5 Amps (peak) AC / 0.2 Amps to 4.8 Amps (peak) DC
95 - 132VAC power supply input / Single 24-48 VDC power supply input
AC: 4 (AC) / 6 (DC) predefined current waveforms to optimize smoothness
LV and HV Step Motors
High Performance
Cost Effective
Optimized for both low-voltage and high-voltage applications
Five frame sizes from 11 through 34
|
|
|
Stepper motors with integrated ministep bipolar chopper drives. They are offered in four versions, featuring programmable motion controller and FIELDBUS interface as well as standard opto-insulated STEP and DIRECTION inputs.
|
|
When selecting your motor there are many parameters to consider including voltage and current available from your drive, speed, resolution, space and cost. The following notes may assist you in your selection of a suitable package:
For an application requiring a speed of less than 5rpm and torque of greater than 1Nm we suggest you consider a permanent magnet stepping motor fitted onto a gearbox. Where a speed of less than 5rpm and torque of less than 1Nm is required you can consider either a permanent magnet or hybrid stepping motor without a gearbox.
|
|
Mounting size : 28 to 106 mm
Step Angle : 0,9° and 1,8°
Holding torque : 0,032 to 19 Nm
Option / customization : encoder, damper, cabling, brake, gear box, vacuum, integrated driver
UL and EN compliant
|
|
|
Stepping motors convert electricity into rotation. And it can be very accurately controlled in terms of how far it will rotate and how fast. Step motors are so named because each pulse of electricity turns the motor one step. Step motors are controlled by a driver, which sends the pulses into the motor causing it to turn. The number of pulses the motor turns is equal to the number of pulses fed into the driver. The motor will spin at a rate that is equal to the frequency of those same pulses. Autonics wide range of 2 & 5 phase stepping motors promise ultra precise, reliable operation and control of the industrial equipment like SMT for semiconductors, office & computer related equipment, medical equipment and so on.
|
|
|
Hurst has nearly 50 years of experience in the design and manufacture of high quality stepper motors. Combining can-stack construction techniques with its permanent magnet expertise, Hurst is able to provide a broad offering of cost effective stepper products. Standard and custom designs are available in step angles from 7.5 to 18 degrees. Unlike its competition, Hurst manufactures its own high quality gear boxes to provide superior performance in any motion control application requiring a stepper motor.
|
|
|
|
Synchronous electric motors: Stepper motors
