|
|
| Garioni Naval offers biomass fire tube steam boilers which are developed based on our cooperation with global engineering and European know-how combining with over 45 years experience and technical knowledge of solid combustibles, especially coal. Biomass steam boilers range from a capacity of 2 ton/h to 10 ton/h with steam pressure from 1 bar to 15 bar. Garioni Naval Biomass steam professional boiler is a two passes fire tube boiler with external prefurnace combustion chamber. The boiler is compactly designed with excellent appearance. |
|
| AEC's M008 is a twin channel gas modulating control board for gas boilers. It controls accurately with PID and contains all the logic for managing the channels. It interfaces well with the FX30LWD to provide total control solution for a highly specified appliance. It is a drop-in replacement for the Gemini 960e combi professional boiler. |
|
Byworth Boilers offer a worldwide spare parts service, supplying professional boiler house ancillaries and boiler and industrial burner spares.
Ancillaries include blow down professional receivers suitable for use with boilers from 250 to 18000 kgs per hour, and feed water tanks in mild or stainless steel manufactured to order.
Spare parts for any manufacture of boiler and most burner manufacturers can be despatched often the same day.
Typical spares offered:
Dunphy burner spares
Nu-way burner spares
Grundfos pumps
Lowara pumps
Danfoss oil pumps
Landis & Gyr controllers
gasket joints
boiler cocks
Byworth can also manufacture replacement industrial furnaces and D patches for boiler repairs, and also boiler fire tubes.
|
|
Professional boiler house components on a modular basis for
simple planning, fast assembly and fully automatic,
safe operation round off the LOOS boiler range in
the best possible way. The individual modules are
assembled completely at the factory and provided
with electrical wiring. The ready-to-use modules only
need to be connected to the supply lines and joined
up to each other. LOOS modular technology considerably
reduces the number of interfaces required,
thus increasing the benefit to the customer.
|
|
- Complete professional boiler house, ready to operate, installed in ISO
containers or in containers for specific requirements.
Installation of chimneys/extension chimneys is possible.
- On site, only a foundation is needed and supply and discharge
|
|
OPTISPARK is the integrated control system developed in cooperation with Cannon AUTOMATA. It consists of two sections: an integrated control system and the user panel (Graphic terminal).
The integrated control system performs many functions usually carried out by several components such as steam pressure, water level, alarm data acquisition suppliers, and it sees to thermal efficiency with the aid of the most advanced control systems: combustion controller through electronic cams, control of the oxygen trim, of the flue gas re-circulation and of the air professional fan by means of an industrial inverter.
The H.M.I. features are: synoptic screens with multi-language
texts; high-resolution colour manufacturers of touch screen display; real-time and historical tracking of selected process trends; alarm reports log; navigator system; multilanguage editor.
OPTISPARK connects to the modern communications systems: it sends SMS and e-mail in case of alarms event; it is displayed on both the Intranet and the Internet; it connects to supervision systems via OPC server.
OPTISPARK's main benefits are: the performance equivalent to the most advanced DCS systems at a lower cost, the optimised combustion, the reduction of environmental impact, of fuel and energy consumption, and of the time for starting and checking the professional boiler. |
|
Electric and automatic professional steam generator, available in five versions, from 6,9 up to 120 kW. Feed water can be connected directly to the main water or from a condensate tank.
Steam professional generator MAXI produces a minimum of 9 Kg/h to a maximum of 170 Kg/h at operating pressure up to 8 bar. |
|
- 1 size with a choice of 12 performance classes ranging
from 8 to 97 kg/h of saturated steam with operating
pressures from 6 to 12 bar
- Also available as pure steam industrial generator made of stainless
steel.
- Can be equipped with fully automatic operation including
automatic blowdown, desalination and automatic control
by timer, professional remote control or central building control systems.
- Availabe as a compact, ready-to-operate unit with professional water treatment and waste water cooling.
- No professional boiler house needed. In many countries, CERTUSS
electric professional steam generators can be installed without permit.
|
|
The three-pass wetback Yorkshireman range is ideally suited to heavy workloads. Add to this the latest combustion technology and control equipment and you'll achieve impressively low running costs and emissions.
Each professional boiler is individually tailored to your specific needs and manufactured from start to finish in our own factory. All professional fittings are mounted in the factory to make installation on site quick and easy.
The boiler can incorporate any make of professional burner to suit a wide range of gaseous or liquid fuels in single, dual or tri-fuel combinations.
Thermal efficiency (based on NCV) in excess of 90% (94% with the optional economiser unit).
External surfaces are heavily insulated and finished in tough, Aluzinc cladding.
Smoke boxes employ the latest ceramic fibre technology offering significantly less heat loss than traditional refractory.
The Yorkshireman range has larger heating surfaces and steam space than comparable boilers, meaning desirable low heat transfer rates, Low NOX emissions, easily achievable outputs, and quality dry steam throughout the firing range.
A wide range of accessories are available to further enhance the boiler; contact us for more details.
Outputs to 10MW (15,900 kg/hr) and operating pressures to 20 bar(g) available. |
|
STEAM-MATIC SM boilers have been developed upon BONO ENERGIA’s significant technical and technological expertise in manufacturing complex, high-capacity thermal equipment.
With over 10.000 installations worldwide, these boilers represent a remarkable achievement and a valid response to the needs of the industrial market which are combined with reliability and high performance.
STEAM-MATIC SM boilers are reliable: severe quality controls during all productive cycle, hydraulic and fire workshop tests before shipment, easy installation and maintenance represent, together with the proved quality of BONO ENERGIA SPA boilers design, the best guarantee for a very long service life.
STEAM-MATIC SM boilers offer superior performance: the innovative design of the pressure vessel ensures excellent heat transfer in two passes. The large volume of water and a wide steam chamber provide high working flexibility and a considerable steam reserve.
STEAM MATIC SM boilers are low consumption boilers, Bono technology ensures a thermal efficiency of 89% reducing consumption of fuel is to the minumim. Additional devices as Flue gas/air or Flue gas/water economisers or Integrated control system Optispark allow to reach 95%!
STEAM MATIC SM boilers can satisfy steam needs from 1 to 5 t/h. |
|
Byworth manufacture fire tube steam boilers in two ranges. The Yorkshireman and Yorkshireman2 ranges are highly fuel efficient three pass wetback steam boilers, available in outputs between 1000 and 18000 kgs per hour and working pressures from 100 to 300 psig (7 to 20 barg). The Yorkshireman2 achieves exceptional efficiency levels by the inclusion of unique XiD fire tubes. These increase the heat transfer from the tube passes by over 80% which in turn leads to overall efficiency of the professional boiler of around 93%. This is without the incorporation of a flue gas economiser. The Yorkshireman range is highly suited to arduous workloads and is extremely robust.
The MX range of fire tube boilers covers 250 to 5000 kgs per hour and is suitable for lighter workloads.
|
|
The economizers exhaust gas boilers GN ECO have been studied to be installed in all types of industrial processes when discharging hot gasses in the atmosphere.
Hot gasses, flowing through the GN ECO are used to heat countercurrent, another fluid utilized in industrial processes, achieving important energy savings while reducing operating costs. |
|
The MX range is a compact and affordable steam boiler ideal for small to medium sized users of process steam.
Each professional boiler is individually tailored to your specific needs and manufactured from start to finish in our own factory, thereby ensuring quality control of the very highest standard. All professional fittings are mounted in the factory to make installation on site as quick and easy as possible.
The boiler can incorporate any make of industrial burner to suit a wide range of gaseous or liquid fuels in single, dual or tri-fuel combinations.
The MX boiler has a thermal efficiency in excess of 89% (based on NCV) .
External surfaces are well insulated and finished in tough, Aluzinc cladding.
The front professional door is lined with the latest ceramic fibre technology offering significantly less heat loss than traditional refractory materials.
The MX range has larger heating surfaces and steam space than comparable boilers, meaning desirable low heat transfer rates, Low NOX emissions, easily achievable outputs, and quality dry steam throughout the firing range.
A huge range of accessories are available to further enhance the boiler; contact us for more details.
Manufactured to BS2790 Class 1 with outputs to 3MW (5000 kg/hr) and operating pressures to 17 bar(g) |
|
The OPRA Generator set manufacturer is the best solution in the 2MW electrical power range to produce steam:
-High Turbine exhaust temperatures
-High exhaust flow
-High Overall efficiency |
|
These boilers make it possible to produce steam, high temperature water or hot thermal oil, from combustion gas coming from industrial diesel engines, gas turbines (cogeneration), industrial kilns, incinerators...
BABCOCK WANSON offers heat recovery boilers (fire-tubes or coil type). Its range of heat recovery boilers goes up to 36 t/h with or without post-combustion.
BABCOCK WANSON offers two types of heat recovery boilers :
- the REC series, fire-tube heat recovery professional boiler ;
- the EXT series, coil heat recovery boiler.
|
|
Bono Energia Heat Recovery Professional steam generators (HRSG) have found application in a wide range of industries where the cogeneration of steam and electricity is required, in order to obtain an independent power station and negligible emission levels.
Bono is able to produce HRSG from gas turbines (both water tube and fire tube) or from engines; heat recovery thermal fluid heaters; turn-key plants.
The standard design of our HRSG allows a "package" modular system (where the professional boiler and the economiser are pre-assembled), which can satisfy many different needs. In this way both the installation and the startup are faster, cheaper and safer. The proven design and the accessibility of the boilers allow high efficiency, minimal maintenance and cost-effective operation.
BONO ENERGIA can boast a fifty years long experience in this sector, and specifically in the heat recovery systems. Our boilers offer high quality levels and match the strictes international standards (API, ASME, PED, EN, DIN, R.I.Na., ABS, SQLO and more).
A team of over thirty engineers allows a continuous R&D effort, and makes possible to offer customised solutions to our clients.
|
|
ROTA has extensive experience in the design and manufacture of large and small capacity industrial steam generators and hot water professional generators using the waste heat from the process cycles.
Heat recovery boilers for cogeneration power stations with engines are equipped with economisers and super heaters depending on the customer needs.
Produced steam can also be used also for electric production with steam turbines.
|
|
The Dalesman range of hot water boilers is highly fuel efficient with low emissions. The boilers are available in outputs from 300 to 10000kW, (1 to 35 million btu), and in working pressures from 100 to 300 psig (7 to 20 bar g).
The Dalesman professional boiler is of exceptional quality and robustness suited to arduous workloads over many years. Unlike other heating boilers available the Dalesman is manufactured using the same engineering and design skills that Byworth use in the manufacture of their steam boilers. All Byworth boilers are manufactured entirely within the factory at Keighley, West Yorkshire. |
|
Type UT-L as flame-tube smoke-tube professional boiler
with 3-pass technology acc. to the Directive
relating to appliances burning gaseous fuels
up to an output of 750-9,200 kW for hot
water generation.
|
|
The three-pass wetback Yorkshireman range is ideally suited to heavy workloads while the MX range is suited to small and medium sized process steam users.
Each professional boiler is individually tailored to your specific needs and manufactured from start to finish in our own factory. All professional fittings are mounted in the factory to make installation on site quick and easy.
The boiler can incorporate any make of professional burner to suit a wide range of gaseous or liquid fuels in single, dual or tri-fuel combinations.
Thermal efficiency (based on NCV) in excess of 89% (94% with the Yorkshireman's optional economiser unit).
External surfaces are heavily insulated and finished in tough, Aluzinc cladding.
Larger heating surfaces and steam space than comparable boilers, mean desirable low heat transfer rates, Low NOX emissions, easily achievable outputs, and quality dry steam throughout the firing range.
A wide range of accessories are available to further enhance the boiler; contact us for more details.
Outputs to 10MW (15,900 kg/hr) and operating pressures to 20 bar(g) available. |
|
The fuel feed system is comprised of all those elements necessary to deliver fuel to the point of consumption, in this case the combustion/gasification chamber.
This is one of the most critically mportant tasks performed by HBC's systems. HBC's advanced and reliable systems incorporate fuel feed units that offer the greatest reduction of uncontrolled air being introduced into the system thereby increasing gasification/combustion efficiencies to a nominal level.
The following narrative begins at the Metering bin. The typical conveyance from the storage area to a metering bin is accomplished through the use of a reciprocating/walking floor. For a detailed description see "Reciprocating/Walking Floor". |
|
The YHB professional boiler is designed for specialist high pressure hot water applications. Built to BS2790, this range is preferred by engineers and consultants worldwide for outputs from 650 to 10500 kW with working pressures up to 20 bar g.
|
|
Many technological processes, above all in the food industry, need to use high temperatures (higher than 250°C).
High temperatures are usually obtained using thermal oil but, new regulations, do not allow to use thermal oil where there is danger to pollute the food under process.
In these cases it is a must to use high pressure steam up to 110 bar, for having temperatures up to 318°C.
We have studied and produce our industrial steam generators GMT/HP that, working with closed circuit and with natural circulation (no pump is needed) can produce steam up to 110 bar.
All installations using GMT/HP work without pump, steam traps, professional water treatment and feed water tanks.
A simple installation using our engineering experience. |
|
Many technological processes, above all in the food industry, need to use high temperatures (higher than 250°C).
High temperatures are usually obtained using thermal oil but, new regulations, do not allow to use thermal oil where there is danger to pollute the food under process.
In these cases it is a must to use high pressure steam up to 110 bar, for having temperatures up to 318°C.
We have studied and produce our professional steam generators GMT/HP that, working with closed circuit and with natural circulation (no pump is needed) can produce steam up to 110 bar.
All installations using GMT/HP work without pump, steam traps, water treatment and feed water tanks.
A simple installation using our engineering experience. |
|
Bono's HTH high temperature heaters are designed for capacities ranging from 2 to 25MW. Thermal fluids, of synthetic type, can be used both in liquid and vapour phase, up to 400°C.
The design of HTH heaters is innovative, gives several advantages versus the coil type design and on the other hand it is extremely reliable, thanks to Bono's experience with more than 2000 installations all over the world.
The main advantages of HTH are: the compact design, especially in terms of height, and the complete accessibility for cleaning and maintenance; the built-in preheater, in the same heater base, reduces the local assembly costs; the accessibility of the professional furnace allows a cheap repairing, since any tube is replaceable working inside the furnace.
HTH are supplied equipped with industrial burner, regulation equipment, instruments, built-in preheater, safeties and accessories, in a transportable package, thanks to their original compact design. The package, ready to be connected to the network, is tested in Bono Energia's workshop before shipping, ensuring a quick and efficient site commissioning and start up.
All Bono's heaters are constantly updated by 30 engineers to the strictest international norms, in order to insure higher efficiency to save money and lower level emissions. |
|
The superheated water boilers made by Bono Energia are designed for thermal capacities ranging from 5 to 60MWt, with hot water outlet temperatures up to 260°C and pressures up to 65bar.
CTH boilers offer a reliable solution for applications such as district heating or industrial processes where hot water (under 120°) is used. For this applications an accurate temperature control and a fast thermal response are needed.
Thanks to their multi-tubular and very compact structure, CTH allow an easy installation and an overall thermal efficiency higher than 94%. The wide professional furnace, water tube screened, helps the thermal exchange and allows to match the most stringent NOx emissions levels. The external walls of the heaters never reach more than 20-30°C above the ambient temperature.
Up to 30MWt, thanks to their innovative design, CTH heaters are delivered in a package solution. Over 30MWt a field erection of the heater is required.
The pressure parts will be delivered in only two sections reducing the local assembly costs.
CTH heaters offer complete accessibility for cleaning and maintenance through proper inspection doors, which allow to fully inspect their interior. |
|
The PHW range of hot water boilers has been introduced by Byworth for commercial and light industrial hot water applications.
With outputs ranging from 120 to 1200 kW and working pressure up to 5 bar g, the PHW gives high efficiency at a very competitive price.
|
|
Combination of high technology and superior workmanship.
Long life, compact design, high capacity to size ratio
Suitable for use of Natural Gas, LPG, Light Oil and Heavy Oil as fuel
Special design to minimize the effects of sediments and scaling on waterside
Well-distributed expansion pattern due to balanced heat absorption within the professional boiler
Also transportable in modular configuration for site assembly, for boiler rooms with narrow passages.
|
|
|
Boilers, Steam generators 
