|
|
|
|
|
|
Trapezoidal Girder Formwork TTR/TTS with plywood or with steel face (60 kN/m²-80 kN/m² according DIN 18218)
Adjustable circular formwork for sewage plants, tank constructions, adventure baths, towers, stairwells, garage entrances, walls for gardening and landscaping
* Continously adjustable from 2 m to 5 m and from 5 m to infinite
* Only 0.28 to 0.55 holes for ties per m²
* Immediately usable = perfect forming times
* Absolutely round and accurate dimensions
* System solutions for haunches and slope balance
* Compatible with all other PASCHAL systems
Trapezoidal Girder Formwork with plywood:
Panel widths (cm): Segments 125,5 / 110,5; 240 /230 (222);
60 / 57,5; 62,5 / 55,5
Panel heights (cm): 300 / 150 / 75 / 37,5
Frame depth (cm): 40 (straight condition)
Plywood: 18 mm; 21 mm
Max. concrete pressure: 60 kN/m² according DIN 18218
Tolerances of deflection: According DIN 18202, table 3, line 7
Trapezoidal Girder Formwork with steel face:
Panel widths (cm): Segments 240 / 230; 120 / 115; 60 / 57,5
Panel heights (cm): 300 / 150 / 75 / 37,5
Frame depth (cm): 40 (straight condition)
Plywood: Steel sheet
Max. concrete pressure: 80 kN/m² according DIN 18218
|
|
|
|
|
|
SVELT is the modular formwork system that allows for the realization of circular-base walls. The walls circumference can be regulated thanks adjustable rods. Once the radius has been set the modules will not deform, thus allowing for an additional level with the same curvature. In this way SVELT can also be used as a climbing formwork. Its versatility also allows for the realization of wall brackets with an “s” shape ovoid base as well as linear wall brackets. With its 6000 kg/m2 capacity, the new SVELT is a much more reliable tool to toughness and stability the two rods and the supporting steel omegas allow lifting and repositioning without neither a change in curvature or deformations. This allows it to be also used as a climbing formwork.
The counter-cast treated multilayer surface with phenolic film can have thicknesses that vary depending on the curvature that is to be applied to SVELT.
Once the casting is done, the system, being composed of modules with a maximum width of 240 cm, can be transported using any kind of truck.
|
|
|
The circular formwork H 20 is the practical choice for smooth, circular walls and radii of any size greater than 3.50 m – universally adaptable.
|
|
RONDA
Circular formwork
When it comes to shuttering curves, RONDA is the No. 1 choice. For RONDA displays a number of unbeatable features for exceptional precision and economy. The RONDA system is based on rugged, ready-to-use elements with an inbuilt spindle system that permits the realization of any desired radius (upward of 2.75 m) with millimeter precision. With two widths available for the inner and outer elements and three panel heights, the system can always be adapted perfectly to the building geometry in question.
|
|
Circular columns are above all required in structural and civil engineering projects.
In skeleton constructions, entrance halls etc. circular columns are a special architectural feature. A second area of application are underground car parks, water basins and bridge piers.
Almost always a perfect concrete finish is required, since finishing works are virtually never carried out on these columns
|
|
Coffrage CTR 3010
SAFETY All the accessories of safety are integrated into the panel including protection front face. Extensible railing for an optimal safety casing Sheet QUALITY ép. the 5 mm for best finished fast concrete vertical Assembly and of high degree of accuracy. Rigid ROBUSTNESS Framework with vertical stays out of V with 2 levels of spacers One more: its use with concrete car placing. SIMPLICITY Accessories entirely colisables Level of passage ergonomic spacers Only one assembly tool. The RANGE Panels HT 3,00 m Under rise HT 1,50 m Under rise HT 1,00 m Spillplates HT 0,50 m
|
|
|
|
