Probes
... field evaluator probe can be used with a digital volt meter (DVM) or oscilloscope to measure AC magnetic field intensities and attenuation ratios. Each probe is carefully calibrated with the calibration ...
Magnetic Shield Corporation
... electrolyte level inside the probe body, this sensor is connected to its electronic inside the probe head;the system generates a local indication (LED) and alarm retransmission in case the electrolyte ...
CLR
... THE AMPLIFIER FOR THE ALCOSENS PROBE The “Transmitter S7” used as measuring amplifier is designed for the connection of one to four probes but can also be extended to any number of probes. ...
Introducing the InfinityXT probe series. InfinityXT enhances and extends FormFactor’s industry-leading Infinity probe family, which has set the benchmark for accuracy and repeatability in the device characterization ...
FORMFACTOR
This glass body conductivity probe, is a traditional two platinum plate electrode design with a nominal cell constant, k = 1 for use with solutions up to about 100 mS/cm. It can be used with either the EP357 Conductivity ...
... electrode design resists sooting and aids in probe burn-off. Burn-Off port as standard with no loss of insertion length Every probe is 100% tested with certification, certificate is shipped with ...
Raman ProbePro product family allows easy and continuous measuring of key process parameters via an optical interface. Raman ProbePro enables time-gated Raman spectrometers to be connected to bioreactors for in-situ, real-time analysis ...
Reflection probe getProbe DR LS NIR diffuse reflectance probe with 2 integrated light sources and a white reference getProbe DR LS is the first intelligent NIR reflectance probe allowing ...
The RDO PRO-X Dissolved Oxygen Probe uses optical technology (EPA-approved RDO technology for Clean Water Act programs) to measure dissolved oxygen and temperature in demanding process environments. This durable probe ...
In-Situ
The full-spectrum water quality monitor is a new generation of environmentally-friendly sensors introduced by Optosky. Easy-to-install cost less, it can measure multi-parameters real-time, automated and transportable. The product adopts ...
Use Transmittance Probes to Measure Absorbance Monitoring the Absorbance Inside Containers and Reactors Fully Configurable Spectrometer (Including Interchangeable Slits) Transmittance Probes with ...
Sarspec, Lda
... higher resolution measurements. The probe provides overload indicators for each input channel as well as for the output. That makes it easy to observe, that the differential probe is working in the specified ...
... Ultrasonic Probe, developed by SIUI, is mainly used for NDT applications. It has a broad range of probes, which include normal probe, replaceable membrane normal probe, ...
At Ether NDE we can offer two types of Conductivity Probes that fit our SigmaCheck Conductivity Meter. We can now offer our standard Conductivity Probe and our 8mm version. APPLICATION: For use with ...
Ether NDE
Specifications Sensitivity/Linearity 4 V/mm (101.6 mV/mil) ±1.5% max Air Gap (Center) Approx 2.7 mm (0.11") Nominal Range: Static ±2.0 mm (0.079") Range: Dynamic 0 to 1,000µm (0 to 0.039") Shaft Diameter ≥80mm Weight ...
CSI Technologies
Zirkonium-dioxide probe (current probe) for a continuous measuring of oxygen concentration, in a range Lambda > 1 without special gas conditioning, in combustion gases, industry exhaust gases and in oven ...
Lamtec
The new Omni Tip™ Hybrid Homogenizer Probes combine the convenience of disposable plastic probes with the durability of traditional stainless steel probes. Hybrid homogenizer ...
The OxyGuard Standard Probe – the probe that revolutionised oxygen monitoring. The probe that you can purchase today is even better than the probe introduced in 1987 ...
OxyGuard
... most up to date probe theory available, drawing on Orbital Motion Limited and as the pressure regimes change, moving on to Allen Boyd Reynolds to account for collisions. The Langmuir Probe is by far ...
Impedans Ltd
Product Description GSP-300 explosion-proof sampling probe is for the explosion-proof occasions. It is applied to a variety of working conditions (high temperature, high humidity, high dust, high corrosion, etc.), supported ...
Hangzhou Zetian Technology CO., Ltd
The STANDARD probes are made entirely of stainless steel. They integrate the measuring tube (Darcy with thermocouple) and the sampling tube with nozzles and filter holder that, united by the slider and fastener to the ...
mega system srl
... by measuring the self-potentials in these soils. The PMS 9000 is a reliable probe which can last for about 15 years. These great advantages allow you to use this probe in soil without maintenance, ...
... immersion probe is that it does not go blind at high sample turbidities. Other probes stop working at 4 000 NTU/FNU (< 1 wt% solids) after which the signal will decrease resulting in an erroneous and ...
General Information Potentiometric oxygen probes developed for the exhaust gas measurements in motor vehicles (λ-probes) are frequently used in industrial equipment. Due to their construction, these ...
ZIROX Sensoren & Elektronik
A multi-parameter probe for the online measurement of ammonium. It is an absolutely reliable device outclassing conventional analyzers in terms of measurement stability and lifetime. Precision is guaranteed by real time ...
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining