|
|
|
This pile was developed based on the ductile pipe that has long been used for water pipelines, and is usually used as a bearing pile for small buildings. The strength is higher than the commonly used structural carbon steel, and the corrosion resistance is more than two times higher. The ducpiles securely support a building, contributing to improving the safety of a house or other small structure.
|
|
|
Autoclave Engineers offers Seamless High Pressure Heavy Wall stainless steel tubing for pressures above 10,000 psi (690 bar) up to over 150,000 psi (10,000 bar). Also available in specialty materials such as Inconel, Duplex, Super Duplex, and others. A complete line of Valves, and Fittings are also available.
|
|
|
|
|
|
Top Line Electropolished tubing sets the standard for service in applications requiring finishes to 15RA maximum. Available in sizes from 1/2" to 4" OD, this full finished stainless steel tubing is available from stock or direct from the mill in 20 foot lengths. All electropolished tubing is fully tested and marked per ASTM A450 requirements. 3
All Top line electropolished tubing is packaged using protective 6 mil poly sleeving with air tight end caps. The tubing is then packageg in wood or Tri-Wall corrugated cartons for maximum protection during shipment.
Finish: Electropolished Tubing is standard with a 15RA max ID with bright annealed/mill OD (ASME BPE surface finish code SFT4). Mechanically polished OD to 32RA or 20RA available on application. The same product is available with a 10RA max. surface finish ID.
Annealing: All tubing is Bright Annealed to a minimum of 1900 degrees F (1040° C) and rapidly quenched.
Cleaning: All Top Line electropolished tubing is rinsed with low TOC de-ionized water. The tubing is then dry purged with 99.998% pure Nitrogen which is filtered to .003 micron at the point of use. The cleaning and packaging is done in a class 100< cleanroom.
|
|
ERW Steel Pipe
Outside Diameter: ø 114mm - ø 356mm (4"-14")
Wall Thickness: 3.0-12.7mm (1/8"-1/2")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 3-12.3m (10'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 150,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
LSAW Steel Pipe (JCOE X 2 Mills)
Outside Diameter: ø 406mm - ø1829mm (16"-72")
Wall Thickness: 6.4-60mm (1/4"- 21/8")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 3-12.3m (10'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 550,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
LSAW Steel Pipe (UOE)
Outside Diameter: ø 508- ø1118mm (20"-44")
Wall Thickness: 6.4-25.4mm (1/4"-1")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 9-12.3m (30'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 600,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
PREMANT®
Ultramodern technology for efficient production
Our pipes are available in dimensions from DN 20 to DN 1000; the types of foam insulation, medium pipes and the system for the monitoring wires can be selected freely.
Thanks to our modern production facilities, we can react rapidly to your requirements.
|
|
Seamless tubes size range »
1.0mm (0.04") to 50.8mm (2") OD. Straight lengths up to 16m (51ft), seamless coiled tubing 6.35mm (1/4") thru to 25.4mm (1") OD.
Our product range consists of straight and coiled tubing. These tubes can be either seamless, welded or welded and drawn.
|
|
SEAMLESS HYDRAULIC LINE TUBES, PHOSPHATED OR GALVANISED FOR PRESSURE AND RETURN PIPING
Material SI 37.4 (E235+N), St 52.4 nbk(E355+N)
Tol. DIN 2391/C or EN 10304-4
Dimensional Range
4,00 x 1.00 mm up to 80,00 x 10,00 mm also in inch-sizes and free Chromium VI
|
|
Welded, welded and drawn tubes size range »
Up to 38.1mm (1 1/2") OD. Straight lengths up to 16m (51ft), coil tubes (with orbital joints) up to 10000m (33000ft) long.
Our product range consists of straight and coiled tubing. These tubes can be either seamless, welded or welded and drawn.
|
|
Sanpress-Pipe 1.4521, stainless steel, for drinking water installations, in 6 m rods,
Sanpress XL-Pipe 1.4521, stainless steel, for drinking water installations, in 6 m rods,
Sanpress-Pipe 1.4401, stainless steel, for drinking water- and gas installations, in 6 m rods
Sanpress XL-Pipe 1.4401, stainless steel, for drinking water- and gas installations, in 6 m rods
Sanpress-Pipe bow 15°, stainless steel
Sanpress XL-Pipe bow 15°, stainless stee
Sanpress-Pipe bow 30°, stainless steel
Sanpress XL-Pipe bow 30°, stainless steel,
|
|
WELDED CYLINDER TUBES IN STAINLESS STEEL
Material: AISI 304; 316 L; 316 Tl
Tol. OD DIN 2463
Tol. ID ISO-Tolerance Field H9-H11
Cenler Line Average of Interior Surface drawn Ra max. 1,0 µm
Dimensional Range: ID ø8 - 200 mm
|
|
|
|
|
|
High Quality Fluoropolymer Extrusion
SAT, an ISO 9001 certified company, produces tubing utilizing specially designed extruders and extrusion processes. Our tubing is made using only ultra-high purity (UHP) PFA and FEP raw materials. Thanks to laser technology and state-of-the-art systems, our tubing’s O.D. and I.D. are kept under constant control, as is electrostatic charge neutralization.
Tube cleanliness is ensured during and after extrusion as a result of our contamination control process. In fact, each tube unit receives a positive nitrogen surge and is then immediately capped and packaged in separate, heat-sealed, double polyethylene bags. The tube coils are then stocked in clean room.
Low Extractables for a High-Tech World
Contaminants are a problem you can’t afford. In fact, impurities result in lower chip yields, higher costs and lower profit margins. Why settle for anything less than high-purity products for your manufacturing processes?
SAT’s PFA and FEP Tubings have very low levels of extractable metals, and this high purity characteristic results in higher wafer yields for the semiconductor industry. Furthermore, high purity means lower costs thanks to reduced contamination, and higher profits due to fewer product defects.
SAT’s PFA and FEP Tubing Features:
* Low levels of extractable fluoride ions
* High crack resistance and strength
* Excellent chemical resistance
* High temperature resistance
* Low chemical carryover and permeability
* Non-flammable
* Low ionic attraction
* High weather and aging resistance
* Excellent dielectric properties
* Non-stick
* High mechanical abilities
* High burst pressur
|
|
MJ - Metal Tube Jacketed (Single Metal Tube)
Copper Tubes:
1/4” OD x .030” Wall
3/8” OD x .032” Wall
1/2” OD x .035” Wall
Welded Stainless Steel Tube:
1/4” OD x .035” Wall
3/8” OD x .035” Wall
1/2” OD x .035” Wall
|
|
Standard：
API SPEC 5CT Standard of American Petroleum Institute
Application：
Seamless steel tubes for oil casing and tubing in oil wells
Model N0．of steel tubes：
J55，N80，L80，P110 etc．
|
|
This Standard applies to seamless precision steel tubes; and, in compliance with ISO/DIS 3304, those tube dimensions have een selectied from the range of manufactura le tu e dimensions which are mainly used as design elements
If tubes having the tolerances and are produced according to the technical conditions of deivery as specified in this Standard are to e used as pipelines, then the dimensions specified in DIN 2448 may from time to time be used. These tubes must be ordered according to quality grade C.
|
|
We can makes and markets cold-drawn and hot rolled seamless steel pipes and cold-drawn special-section seamless pipes which are widely applied in the industries of petrochemical, boiler, automobile, mechanical, construction, chain, electric of the company is 80000t. Our factories through ISO9001:2000 certificate, has aggressive leadships and outstanding professionals.
Specifications:
Size: (Φ6 - Φ680) x (0.5 - 87) mm, but we can also produce other specification according to the customers’ requirements.
|
|
|
It is available in a variety of compositions, most popular of which are ASTM-A-213, Grade TD-321. (16% Cr, 8%N stabilized with titanium) and ASTM-A-213 Grade TD-347 (18% Cr, 8% Ni) stabilized with columbium. Either of these two may be used upto to 649oC. Care must be given to choice of welding rod to avoid brittleness in the welds.
|
|
Stainless Steel Pipe
Seamless to EN ISO 1127
Produced in approx. 6 m lengths
sf 800 m
Stainless Steel Pipe
sf 800 m
Capillary Tube
Microtubing
sf 800 z
Imperial
Stainless Steel Pipe
|
|
|
Ductile iron pipes have the corrosion resistance of cast iron and almost the same strength and ductility of steel. Because of their high reliability, ductile iron pipes are widely used in pipelines to convey potable water, sewage water, agricultural or industrial water, gas, etc. Recently, there has been a strong demand for earthquake-resistance ductile iron pipes, especially those employing NS-type earthquake resistance joints, with about 50 percent of our current domestic-oriented shipments being earthquake-proof piping.
|
|
|
This heat transport pipe consists of an inner pipe with a layer of thermal insulating material, and a reinforcing layer formed around the inner pipe. Responding to the need for transporting heated mediums such as steam, and heated or chilled water, this product has been developed and is contributing to the efficient use of energy. For example, heat transport pipes have been installed in area-wide air conditioning systems and other facilities that utilize excess and waste heat or geothermal energy.
|
|
Welding accessories for piping in stainless steel
ISO Unions with conical seat, or with PTFE flat seat(BSP or NPT)
3000 Lbs forged unions (NPT) with socket welding (SW)
Coupling SW, half coupling SW, female cap SW, elbow SW, tee SW
ISO, Metric, ANSI standards
90°elbow, 45° elbow, tee with sleeve, tee without sleeve
Concentric reducer, excentric reducer, collar, pipe cap
...
|
|
Threaded accessories for piping in stainless steel
ISO Unions with conical seat, or with PTFE flat seat(BSP or NPT)
3000 Lbs forged unions (NPT)
Bent unions male/female or female/female (BSP / NPT)
welding nipple, barrel nipple, hexagonal nipple, male plug
female coupling, half coupling, female cap
Bulkhead coupling
Reducer (male/male, male/female, female/female, female/male)
90°elbow, 45° elbow, reduced bend
Threaded tee, reduced tee, cross
...
|
|
|
FG Inox proposes its stainless steel accessories to weld : bends, tees, reducers, caps and collars in ISO, METRIC and ANSI (schedule) standards.
|
|
316L machined stainless steel unions, threaded, with hose shank or to weld with flat or conical seat.
From ND 5 to ND 100.
MWP at 20C: 64 bars < ND 50 and 40 bars > ND 50
FG Inox proposes 316L stainless steel threaded nipples, barrel or hexagon nipple, adaptors, couplings, elbows, tees, reducers and plugs.
|
|
|
As the number of large construction projects in areas with weak ground and coastal areas continue to increase, designing and building earthquake-resistant structures has become even more important than before. Accordingly, foundation piles are required to have higher levels of yield strength, workability, and structural reliability. Kubota steel pipe piles meet this requirement. The steel pipe piles have already been used in a number of construction applications such as bridges, ports, rivers, and buildings.
|
|
Stainless steel pipe fittings for dairy and food industries
Béné Inox offers you a complete range of unions and pipes fittings
stainless steel 304L and 316L
for SMS, DIN, Tri-clamp, Macon standars
Butterfly valves (manual or automated), pneumatic seat valves
Check valves, filters, sigth glasses...
Unions for welding, unions for expanding, unions for hose fitting
male part, liner, nut, blind nut, with EPDM/FKM/Viton/PTFE gasket...
SMS/BSP adaptor, DIN/BSP adaptor
Bend at 90°, at 45°, at 180°, tee, reduced tee
Concentric reducer, excentric reducer, pipe cap, collar
Threaded stirrup, clamp, pipe holder, pipe
We also have an "industry" range of fittings (ISO,ANSI standards...) :
Valves, unions, flanges, elbows, tees, réducers...
|
|
FG Inox offers 3 standards of stainless steel of food fittings : SMS, DIN, MACON. Among this standards, FG Inox offers threaded fittings, welding fittings, valves and pipes.
All these products are made for alimentary using.
|
|
|
The FW pipe, a fiber reinforced plastic pipe consisting of FRP and resin mortar, is used for pipelines carrying agricultural or sewage water. Since FW pipes are strong and have excellent hydraulic characteristics, corrosion resistance, earthquake resistance, and workability, they are widely utilized in both new construction and renovating applications.
|
|
| ... products without technical information |
| |
 see the results for the following category : Hoses |
|
|
