Ball joints, Wheel type rollers

Ball joint heads GN 648.1 are similar to DIN ISO 12240-4, series K (formerly DIN 648 K).

Ball joints GN 648.8 are similar to DIN ISO 12240-4, series K. These ball joints are integrated in the ball joint heads GN 648.1 and GN 648.2.

Owing to the anodized coating of the fork head, the bearing is virtually non-wearing.

Clevises DIN 71752 / DIN ISO 8140 / CETOP RP102P are some of the most frequently used linking elements in industry. These parts can be found everywhere where simple movements are required, e.g. linear pulling, pushing or even axle offset ...

MBO Clevises are U-shaped or forked metal connectors to which another part can be fastened by means of a bolt or pin passing through the ends of the connector. Clevises are used commonly in the industry for carrying out pulling, pushing, ...

The MBO elongated hole is ideally used to link elements in the industry especially when adjustments are required in the area of the cross hole. This tool comes with the corresponding mating pieces and can be easily combined with a clevis ...

Construction: Stainless steel with nylon roller Temperature Range: 32 to 230°F Mounting: 31/64 dia. mounting hole fits #15/32-32 threaded mounting section of valve bodies Operation: Mounts to valve body, actuates valve when mechanically ...

Our DRS wheel block system is a versatile travel wheel system for heavy-load handling applications. With the DRS-M, we have enhanced this system further and added new features to it. Both product ranges can be seamlessly integrated into ...

Using our LRS travel wheel system, you can meet your drive requirements quickly and reliably for transport, feed, transfer, distribution or merge applications. We can supply you with the travel wheels and drive units to suit every application. ...

Inside diameter: 125 mm - 400 mm

Our RS wheel block system is suitable for applications in which a housing made of sheet steel is required, such as for impact loads. The RS system is also employed in high-temperature applications up to 250 °C or wherever a stainless ...

Rod ends with ball bearing internal thread Material: Casing drop-forged steel, tempered. Version: Galvanized. Internal clearance 15 - 40 µm. Note: The hardened ball bearing is long-term greased and sealed with cover washers. The connection ...

The 27650 by Norelem is a Ball joints DIN 71802 which is made of steel or 1.4305 stainless steel. It comes with a surface finish which is either galvanized or chromated. Plus, upon request, a left handed thread can be achieved. For its ...

Axial joints for tractive forces adjustable Material: Steel. Version: Ball thrust pins galvanized and chromed. Ball seat and nuts galvanized. Note: Axial joint suitable for taking up tractive forces. The ball's movement can be controlled ...

Description To guide moving parts in the slot of the aluminum profile Material Roller: Nylon PA, glass ball reinforced Bush: Steel, zinc plated Washer: Steel, zinc plated Color Black Pack Quantity 10 pieces Specials conductive, other ...

Profile slides for aluminium slot profile Profile gliders for the sliding guidance of aluminium profiles Economic and wear-resistant solution for sliding doors or panel elements Design: with/without clamping lever Design: fixed/loose ...

Description To guide moving parts in the slot of the aluminum profile, with ball bearing Material Nylon PA, glass ball reinforced Color Black Pack Quantity 10 pieces Specials conductive, other colors on request

Outer diameter: 60 mm - 125 mm
Inside diameter: 15 mm - 25 mm
Load capacity: 20 N - 25 N

guide rollers use a thermoplastic polyurethane tread which is cast directly onto a nylon wheel centre, in contrast to FPU series wheels. With a hardness of 92 Shore A, the tread forms a chemically bonded and irreversible connection with ...

Outer diameter: 30 mm - 75 mm
Inside diameter: 5 mm - 25 mm
Load capacity: 200 N - 1,250 N

The Blickle Extrathane® tread of the FTH guide roller series is cast directly onto the ball bearing. The ball bearings are sealed on both sides, providing outstanding protection against contamination. The wheels provide a low level of ...

Outer diameter: 40 mm - 125 mm
Inside diameter: 10 mm - 25 mm
Load capacity: 450 N - 3,300 N

guide roller series has a steel wheel centre with a cast Blickle Extrathane® polyurethane tread. The ball bearing is sealed on both sides, pressed into the wheel centre and secured with a locking ring. Like the FSTH wheel series, the ...

► Lockable displacement position Be flexible in your application, customise the handling to your workpiece and lock the displacement position with process reliability ► Large locating flange The large mounting surface simplifies ...

Unmounted bearing assembly consisting of hardened precision ground inner and outer raceways with either full complement or separated (cage) needle, ball, tapered or cylindrical rolling elements constructed with an integral stud or precision ...

NEFF offers an extensive range of common accessory parts for screw jacks, from precise gimbal bearings to ready-to-install pillow block bearings. We also manufacture custom-tailored solutions in our modern machine park on request.

NEFF offers an extensive range of common accessory parts for screw jacks, from precise gimbal bearings to ready-to-install pillow block bearings. We also manufacture custom-tailored solutions in our modern machine park on request.

NEFF offers an extensive range of common accessory parts for screw jacks, from precise gimbal bearings to ready-to-install pillow block bearings. We also manufacture custom-tailored solutions in our modern machine park on request.

Outer diameter: 85 mm - 85 mm
Width: 60 mm - 110 mm
Load capacity: 600 daN - 1,100 daN

Perfect for use on electric pallet trucks, both walk-behind and with operator on board models, even in case of handling very heavy loads, at speeds above 12-16 km / h, and intensive use even over long terms. The excellent rolling resistance ...

Outer diameter: 85, 80 mm
Width: 40 mm - 100 mm
Load capacity: 700 daN - 1,000 daN

Excellent for use on electric pallet trucks, also in case of heavy loads and high speed handling (up to 16 km/h). Their excellent values of rolling resistance make the manual handling of heavy loads easier. TECHNICAL FEATURES ROLLER ...

Outer diameter: 85, 80 mm
Width: 70 mm - 100 mm
Load capacity: 650 daN - 1,000 daN

Excellent for use on electric pallet trucks, also in case of heavy loads and high speed handling (up to 16 km/h). Their excellent values of rolling resistance make the manual handling of heavy loads easier.The model with electrowelded ...

Outer diameter: 100 mm - 800 mm

Our wheel heads are ideal for gantry and semi-gantry cranes, and are available in a wide range of wheelbases, wheel channels and diameters to suit your unique requirements. If your cranes require end carriages, wheel heads or bogies, ...

Outer diameter: 48, 80 mm

Our foam rotation wheels (rollers) are specially designed for rotating glass bottles and containers on inspection machines. Their custom-made design ensures perfect compatibility with your equipment and optimizes the reliability of the ...

Our rollers bearings for inspection machines, also known as star wheel rollers, are made of a ball bearing core coated with 92 Shore polyurethane (PU). Designed to ensure smooth and accurate rotation of glass bottles, these rollers are ...

Outer diameter: 10, 60, 80, 120 mm

The driven version of TRAPOROL's all-side rollers can be mounted around the axles. The rollers are extremely robust and ensure smooth and trouble-free handling during conveying, turning and pushing. TRAPOROL’s polydirectional rollers ...

Standard Hydraulic Cylinders Attachments - Ball-joint DIN 24338 - ISO 6982

Standard Hydraulic Cylinders Attachments - Fork joint hinge ISO 8133

For Hidraulic Cylinder Components BALL-JOINT ENDS

We offer wheels and rollers for inspection machines that conduct inspection by rotation of bottles and jars. We offer various dimensions, thicknesses and shapes to meet your needs. Wheels with pins, foam wheels, S.A.R. wheels and rollers ...

Outer diameter: 1.5 in
Inside diameter: 0.89, 0.88 in

Solid rollers have a smooth surface and are permanently bonded to a steel insert. The steel insert provides rigidity and allows the user to customize the mounting configuration based on the application. Rollers are available in neoprene, ...

Outer diameter: 2, 2.5, 4 in
Inside diameter: 1.25 in

Finned rollers have grooves on the surface and are permanently bonded to a steel insert. The steel insert provides rigidity and allows the user to customize the mounting configuration based on the application. The grooves create less ...

Outer diameter: 1.5 in - 6 in
Inside diameter: 0.5 in - 0.51 in

Solid rollers have a smooth surface and are permanently bonded to a steel insert with the bearings held into place with snap rings. Rollers are available in neoprene, nitrile and urethane materials with hardness ranging from 20 to 95 ...

Threaded rods for leveling feet. Material: Zinc plated steel Color: Galvanized Packaging Unit: 10 pcs. Extras: Available in different lengths