- Detection - Measurement >
- Position, Speed and Acceleration Measurements >
- Miscellaneous sensors
Miscellaneous sensors

● Moving gantry structure,measuring specimen fixed on stage ● CNC fully auto close loop control, auto measurement; ● Precise “00” grade “JINANQING” marble base and pillar ensures corrosion resistant,and working stability. ● Automatic ...
Mikrosize

Portable combustible gas detectors are a repacement for the succesfull XP-3110 and XP-3160 portable gas detectors. Portable combustible gas detector, easy to use for the detection of combustible gases and solvent vapours. For safety ...
New Cosmos

The XPS-7 II suction type portable gas detector is a unique detector which enables you to switch easily between gases when needed. The sensors are kept under power in a so-called sensor stocker. The stocker can keep up to 6 sensor cartridges. ...
New Cosmos

PS-8 - Single to Multi channel gas detector A suction type detector for indoor use for detection of gas leaks in semiconductor factories. Sensor units are factory calibrated and delivered to site ready for use. Communication ...
New Cosmos

COMSAT has four different types of warp guard depending on the types of threads to be processed. The COMSAT IR model is based on a photoelectric stop system for the detection of wire breaks. The Eltex-UNI, Eltex-Unimag and Eltex EyETM ...
COMSAT

COMSAT has four different types of warp guard depending on the types of threads to be processed. The COMSAT IR model is based on a photoelectric stop system for the detection of wire breaks. The Eltex-UNI, Eltex-Unimag and Eltex EyETM ...
COMSAT

COMSAT has four different types of warp guard depending on the types of threads to be processed. The COMSAT IR model is based on a photoelectric stop system for the detection of wire breaks. The Eltex-UNI, Eltex-Unimag and Eltex EyETM ...
COMSAT

NON-CONTACT CAN SENSOR SP7001, SP7002 Monitor CAN FD/CAN Signals Without a Sub-Harness Overview The SP7001 and SP7002 are CAN and CAN FD signal sensors that use non-contact technology to accurately capture CAN bus signals necessary ...
HIOKI EUROPE GmbH

WES Systeme Electronic GmbH

WES Systeme Electronic GmbH

WES Systeme Electronic GmbH


analog inputs signal conditioning moduleSCM5B Series
Each Dataforth 5B module provides a single channel of isolated analog input or output. - Input modules interface to all types of external sensors, then filter, isolate, amplify, and convert the input signals to high-level analog voltage ...
Dataforth Corporation

The SCM5B48 provides excitation to piezoelectric sensors with built-in microelectronic amplifiers, commonly known as ICP®* or IEPE* or LIVM* sensors. The module provides a constant current excitation to the sensor, then isolates, filters, ...
Dataforth Corporation

The SCM5B48 provides excitation to piezoelectric sensors with built-in microelectronic amplifiers, commonly known as ICP®* or IEPE* or LIVM* sensors. The module provides a constant current excitation to the sensor, then isolates, filters, ...
Dataforth Corporation

The 8065 vibration module is designed to power and accept an AC signal from a constant-current accelerometer. The module integrates this signal and provides a 0-10V output proportional to RMS velocity and enveloped g output plus a buffered, ...
Monitran

The PD6014-40 is composed of two wires, and an AC power switch. The vibration-proof unit utilizes a voltage range of 110 up to 220 V AC. The device functions in a power capacity of 3 A to 110 V AC. In addition, it provides a break angle ...
The Comus Group

The PD6021 model, engineered by Comus, is an inductive proximity switch that features a 2 wire design. In addition, this device runs on an utmost current of 1A and on a voltage range from 6~30 VDC. Specifications 2 Wires DC Proximity ...
The Comus Group

Contact Capacity: 1.0 A, 120 VAC Operation: 90º Tilt w/ arrow toward the front, contact is open Break Angle: 45º Against Horizontal ABS Plastic Housing
The Comus Group

Spark detector RIV-601P/S is an electronic fire alarm device, sensitive to sparks and incandescent bodies in movement. Its use is particularly recommended on dust collection systems in factories where wood is processed, chipboard or ...

Eltex thread sensor 15965. This thread sensor is designed to monitor up to 6 sewing threads on automatic sewing machines. It checks that the thread is moving in stitches. Both no thread movement and continuous thread movement will ...
Eltex of Sweden AB

Eltex UPG-Stitch Thread break sensor for sewing machines. The UPG-Stitch is a thread break sensor designed to be used on sewing machines. It checks that the thread is moving in stitches. Both no thread movement and continuous thread ...
Eltex of Sweden AB

Eltex G3s Yarn Break Sensor G3s is a yarn break sensor that uses piezoelectric technology to detect yarn movement (not presence) of all types of yarns in many different applications. It does not require a Central Control Unit, making ...
Eltex of Sweden AB

• High performance ASIC based advance sensor • Adaptive threshold adjustment for detecting various opaque labels • Fast response time 150us • Minimum label gap 2mm • Dynamic learning mode or gap (base) learning mode possible • Build ...

The Microdust Pro is a real-time hand-held, data logging instrument for the detection of airborne dusts, fumes and aerosols. It is ideal for walk-through surveys and for checking the effectiveness of control measures. It is a simple to ...

The SONOCHECK ABD06 Series manufactured by SONOTEC is an air-bubble detector applicable for measurement chambers and fluid-filled tubes in detecting gas and air bubbles. This device is also used for the monitoring of liquids and wet/dry ...

SONOCHECK air bubble sensors of the ABD05 and ABD07 series incorporate intelligent ultrasonic transmission technology and innovative safety concepts in order to provide maximum sensor reliability. Depending on the sensor type, the various ...

* Measurement of CO concentration in the ambient air * Test CO leakage from furnaces, water heaters, stoves * MWC-Value-Measurement (Maximum Workplace Concentration)

The MEMS-based MTS1TEMP56 detects infrared radiation for non-contact temperature measurement. The 56 silicon thermopiles absorb the incoming radiated energy. The integrated mass absorber ensures the efficient conversion of the radiated ...
Micro-Hybrid Electronic GmbH

The MTS1HIGHTEMP is a high-sensitivity, single-channel thermopile detector for precise, non-contact temperature measurement by sensing emitted infrared radiation. The thermopile absorbs the energy, converts it to electrical voltage and ...
Micro-Hybrid Electronic GmbH

The high sensitivity Thermopile single channel detector with 80 bismuth antimony/antimony thermocpouples is based on MEMS technology. The very high detectivity of up to 12.2*10^8 cm√Hz/W, as well as the high sensitivity of up to 501 V/W, ...
Micro-Hybrid Electronic GmbH

Traditionally, the amount of dissolved carbon dioxide is measured using a methodology commonly called "manual shaking" (aka piercing device) where a container with pierced hole is shaken vigorously in a metal frame. It requires strenuous ...

Generator – frequency simulator (pulses) Hz, KHz with PNP, NPN, namur, PUSH PULL, TTL, AC, .. output. Frequency range 0.1Hz to 100 KHz.

CPQT is a programmable transmitter for all distribution networks. All variables that can be measured with the transmitter can be programmed as desired via 2 analog outputs. The configuration takes place with our easy-to-understand software ...

The Airnet II is ideal for remote continuous particle monitoring as a component of a Facility Monitoring System. It meets the specifications of ISO 21501-4 and EU GMP Annex 1 to measure the size and number of particles suspended in the ...

As part of a facility monitoring solution, the Airnet® II and IIs Particle Sensors from Particle Measuring Systems are an EU GMP Annex 1 solution that meets the specifications of ISO 21501-4 to measure the size and number of particles ...

The OMD-351-O2 online oxygen monitor combines a rugged CE marked wall mount design with SSO2’s precision oxygen sensor technology. The unit is designed to safely measure breathing air oxygen in confined spaces. The unit comes with a ...

The OMD-351-O2-CO2 online dual oxygen and carbon dioxide monitor combines a rugged CE marked wall mount design with SSO2’s precision sensor technology. The unit is designed to safely measure breathing air oxygen and carbon dioxide in ...

The MED-19 portable oxygen monitor combines a modern rugged CE marked design with Southland Sensing’s precision oxygen sensor technology. The unit is specifically designed to safely and easily verify oxygen and other medical gases used ...


breathing simulatorOXY ROBOT
Metabolic breathing simulator Oxy Robot is to test breathing apparatuses (SCBA, Airline BA, SCSR on chemically bonded or compressed oxygen, EBA) and other RPE. Operation: Test equipment recreates the exchange of gases and the process ...

Pressure breathing simulator OXY ROBOT is to test closed- and semi-closed circuit rebreather (CCR, SCR) according to EN 14143, open-circuit SCUBA, RPE with mouthpiece and full-face mask. Test equipment is suitable for tests in the pressure ...

Building systems technology in very general terms comprises electrical and electronic equipment and automation devices for industrial, commercial and private buildings. These equipment and devices range from bell transformers to the Dupline ...

The device innovation GMS 4000 is the universal device for leak detection, network control and gas analysis. With infrared measurement technology, the measuring instrument can determine natural gas and CO2 exactly and without cross-sensitivities. ...
Schütz GmbH Messtechnik

The main task of the GM 5 is the search for gas leaks in underground and exposed natural gas pipelines. The GM 5 can also be used for gas leak detection with hydrogen mixtures (tracer gas technology). With the GM 5, Schütz Messtechnik ...
Schütz GmbH Messtechnik

The main task of the GM 3100 is the search for gas leaks in underground and exposed natural gas pipelines. However, it can also be used with the optional sensors to check e.g. biogas plants. The innovative device GM 3100 is the universal ...
Schütz GmbH Messtechnik

The G.R.A.S. 43AA Artificial Ear is a complete test jig for acoustical measurements on telephone handsets and earphones. It includes an IEC 318 Ear Simulator RA0039 which is individually calibrated according to the ITU-T Recommendation ...
G.R.A.S. Sound & Vibration

Illuminance is the most frequently made measurement within general and specialist lighting applications. The two most important qualities required of a high precision illuminance detector are a spectral responsivity that is very well ...
Gigahertz Optik GmbH

The VL-3704 is a reasonably priced illuminance measurement head whose photometric responsivity and cosine field of view correspond to the DIN 5032 - Article 7 quality class B. The detector can be combined with all optometers and light ...
Gigahertz Optik GmbH

The VL-3705 is an illuminance measurement head whose scotopic responsivity and cosine field of view correspond to the DIN 5032 - Article 7 quality class B. The detector can be combined with all optometers and light meters from Gigahertz-Optik. ...
Gigahertz Optik GmbH
Your suggestions for improvement:
Subscribe to our newsletter
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining