Center-clamping vises

7 companies | 29 products
{{#pushedProductsPlacement4.length}} {{#each pushedProductsPlacement4}}
{{product.defLight}}
{{#if product.requestButtonsVisibility.requestButtonQuestion == "ACTIVE" || product.requestButtonsVisibility.requestButtonWhereToBuy == "ACTIVE"}}
{{/if}}
{{product.productLabel}}
{{product.model}}

{{#each product.specData:i}} {{name}}: {{value}} {{#i!=(product.specData.length-1)}}
{{/end}} {{/each}}

{{{product.idpText}}}

{{productPushLabel}}
{{#if product.newProduct}}
{{/if}} {{#if product.hasVideo}}
{{/if}}
{{/each}} {{/pushedProductsPlacement4.length}}
{{#pushedProductsPlacement5.length}} {{#each pushedProductsPlacement5}}
{{product.defLight}}
{{#if product.requestButtonsVisibility.requestButtonQuestion == "ACTIVE" || product.requestButtonsVisibility.requestButtonWhereToBuy == "ACTIVE"}}
{{/if}}
{{product.productLabel}}
{{product.model}}

{{#each product.specData:i}} {{name}}: {{value}} {{#i!=(product.specData.length-1)}}
{{/end}} {{/each}}

{{{product.idpText}}}

{{productPushLabel}}
{{#if product.newProduct}}
{{/if}} {{#if product.hasVideo}}
{{/if}}
{{/each}} {{/pushedProductsPlacement5.length}}
machine tool vise / pneumatic / horizontal / 5-axis
machine tool vise
MAP series

Max. clamping force: 1,720 N - 17,300 N
Stroke: 8 mm - 12 mm

... Connections: sides-base - Maintenance: relubrified every 10.000 cycles when used in handling. When used in machining centers for tool clamping, lubricate every 5.000 cycles

See the other products
OMIL Srl
machine tool vise / pneumatic / horizontal / low-profile
machine tool vise
CFB series

Max. clamping force: 4,500 N - 55,000 N
Stroke: 4 mm - 30 mm

... Connections: sides-base - Maintenance: relubrified every 10.000 cycles when used in handling. When used in machining centers for tool clamping, lubricate every 5.000 cycles

See the other products
OMIL Srl
machine tool vise / pneumatic / spring / self-centering
machine tool vise
CFB MC series

Max. clamping force: 6,280 N - 47,300 N
Stroke: 4 mm - 16 mm

... Connections: sides-base - Maintenance: relubrified every 10.000 cycles when used in handling. When used in machining centers for tool clamping, lubricate every 5.000 cycles

See the other products
OMIL Srl
machine tool vise / 5-axis / hardened steel / self-centering
machine tool vise
Makro-Grip Series

Max. clamping force: 14, 20 kN
Stroke: 0 mm - 355 mm

Makro-Grip 5-Axis Vice - Compact and unmatched holding power for the 5-face machining of blanks and unfinished parts. - Best accessibility for 5-face machining - Exceptional holding power with lowest clamping ...

vise with clamping system / for machine tools / universal / 5-axis
vise with clamping system
Avanti

Makro-Grip Avanti - the universal vice with great handling characteristics and unbeatable top jaw prices - Enormous savings of set-up time due to quick jaw exchange system - Clamping set-up can be ...

machine tool vise / 5-axis / precision / hardened steel
machine tool vise
Vario-Tec

Max. clamping force: 14, 20 kN

... - highly precise machine tool vise for finishing tasks - Ideal for challenging machining tasks of workpiece rear-side - Highest centering and repeat accuracy - Endstops and parallels are not needed anymore - Clamping ...

machine tool vise / pneumatic / horizontal / vertical
machine tool vise
BLOCK-SC

Max. clamping force: 8 kN - 20 kN
Stroke: 6 mm - 8 mm

... performed from the sides or the base of the body – Pneumatic supply up to 9 bar FUNCTIONING Pneumatically actioned wedge clamping system: the multiplication of the pneumatic force is performed by actioning the wedges. ...

machine tool vise / center-clamping / multi-person
machine tool vise
AMROK series

... can be held using the same CDV - Requires minimal excess stock to clamp and locate parts - No additional custom workholding components are required TIME SAVINGS - No change-over of jaws to hold different ...

machine tool vise / self-centering / compact / center-clamping
machine tool vise
MZR series

Max. clamping force: 16,000, 30,000, 40,000, 50,000 N
Stroke: 19 mm - 114 mm

... self-centering vise-series MZR is used as a cost-effective clamping tool for clamping raw parts on multi-axis machining centres. With its compact, maximum access to ...

See the other products
Spreitzer GmbH & Co. KG - Präzisionswerkzeuge
machine tool vise / steel / self-centering / center-clamping
machine tool vise
MZE series

Max. clamping force: 5,000 N - 70,000 N
Stroke: 12 mm - 178 mm

... economic centre-clamping vise solution for work on pallets or automation systems. Advantages at a glance Maximum access and wide clamping range Suitable for external and internal ...

See the other products
Spreitzer GmbH & Co. KG - Präzisionswerkzeuge
machine tool vise / steel / self-centering / center-clamping
machine tool vise
MZU series

Max. clamping force: 16, 30, 40, 50, 70 kN
Stroke: 19 mm - 175 mm

... variable tiered form, all clamping possibilities are covered. The centre-clamping vise type MZU is especially suitable for flexible raw parts clamping. Advantages ...

See the other products
Spreitzer GmbH & Co. KG - Präzisionswerkzeuge
machine vise / screw / steel / center-clamping
machine vise
F677-580605

Stroke: 150 mm

TriMax M vises increase clamping capacity with extended base lengths up to 878mm. XL vises in the TriMax M line feature extended base lengths (758mm and 878mm) for increased clamping ...

machine tool vise / for grinding machines / center-clamping
machine tool vise
FQV series

Max. clamping force: 2,000 daN

... milling machine vise for holding shafts FQV are used on milling machines , grinding machines, drilling machines and CNC machining centers. Properties and application: Two movable jaws press the round-shaped ...