Electronic amplifiers

Voltage: 18 V - 240 V
Power: 18 W
Frequency: 45 Hz - 65 Hz

... distribution amplifier. Cost-Effective Capacity Microsemi's TSC 4340A fiber optic distribution amplifier provides a cost effective upgrade path, enabling networks to multiply the output from one UTCG to 8. For example, ...

Voltage: 2.5 V
Frequency: 20 kHz - 220 kHz

... Hinds’ Exicor Systems the Signaloc is now availaible for anyone who can use a dual-phase, analog, single frequency lock-in amplifier. You choose the frequency – any frequency between 20-200 kHz. You choose 1f or 1f and 2f demodulation ...

... The Fiber Optic Amplifier is a photoelectric sensor from the FX Series. It is designed with a standardized DIN rail fiber optic for mounting power supplies. This device comes with a Teach-in (FX4) or trimmer sensing adjusting (FX3). ...

Voltage: 20 V - 253 V
Current: 0 mA - 20 mA

... TV 22 GL isolation amplifier is used for galvanic isolation and amplification of DC signals (mA). Description Input and output are galvanically isolated with a high degree of isolation. The integrated high-efficiency electronic ...

Current: 8 A
Power: 1,912 W

... from control logic power. The amplifiers are interfaced to a PMAC controller via ACC-24E2, ACC-24E2M, ACC-24E3 (Power PMAC only), ACC-8F or ACC-8FS. These drive amplifiers are designed to receive logic-level direct digital ...

Power: 0 W - 8 W

... MPBC’s Raman Fiber Amplifier System is capable of amplifying a narrow, linearly-polarized, NIR input signal with minimum spectrum broadening. NIR output powers of up to 15 Watts at wavelengths between 1030 nm and 1370 nm can be achieved ...

... • Charge amplifier 2661: This standard amplifier is used if there are no additional certificates required. • Charge amplifier 2667: This amplifier is ATEX certified for use in Zone ...

Current: 3 mA - 5 mA

... The Trig-Tek™ 201AP Charge Amplifier is designed to amplify the outputs from piezoelectric- or mV-type accelerometers, force gauges, microphones, and pressure pickups. The “Charge” output from the pickup, expressed in mV or pC/g,is then ...

... solutions for stereo headsets Features - Bypass function - >25dB noise reduction achievable - High quality audio chain - Fully electronic calibration - Single cell (AA/AAA) or 1.0V - 1.8V supply Benefits - Listen to audio even without ...

... Compact, light weight, battery or AC powered constant current sensor amplifier suitable for field measurement. The SR-2200 amplifier accepts constant current line drive sensors and connects the signal to analyzers and ...

Voltage: 0 V - 10 V
Current: 4 mA - 20 mA

... model LCB20 load cell amplifier and digitiser. Play LCA20 video to learn more about the features Full digital set–up using PC or keypad 3 x configurable digital inputs e.g. for autotare, peak hold ...

... The 4711A1 series from Dytran is an in-line charge amplifier that is especially designed with stainless steel to ensure highly durable performance when in use. It features a 10-32 jack input connector and a BNC plug output connector. ...

Diodes op-amp range provides Industry standard parts for general purpose consumer and industrial applications. Many devices are specification matched and pin for pin compatible with industry standard parts.

... distribution features in one time and frequency distribution unit. The base unit is a dual input, 24 output frequency distribution amplifier suited for 5MHz or 10MHz. Each output is monitored and will set the alarm if an output fault ...

Voltage: 0 V - 10 V
Current: 4 mA - 20 mA

... cell amplifiers measure just 19mm in diameter and 7.6mm in height and are designed for incorporation into the body of a broad range of strain gauge transducers and load cells. When internal mounting is not possible, the ICA load cell ...

Voltage: 5 V

Voltage: 24 V
Current: 10 mA

... Designed for strain gage sensors or potentiometers DIN rail fixture Front panel calibration shunt Compatible with the MCS trigger level modules The MCJ conditioner is fixed on a DIN rail in a polyamide casing. the I/O electrical connection are through ...

Voltage: 3.3 V

... The PAD2 is a portable and universally usable forcemeasurement amplifier with a digital display. The samplingfrequency can be adjusted in the range of 10 Hz (slow),20 Hz (medium) and 100 Hz (fast). The calculation ofaverages ...

... These transimpedance amplifiers are particularly useful for the measurement of current from photodiodes. The output is a voltage linearly proportional to input current and thus, to input power in photodiode monitoring applications. Their ...

Voltage: 24 V
Current: 5 mA

... Montalvo s M-3224 Strain Gauge Load Cell Amplifier is powered by 24 VDC. The M-3224 is used in conjunction with one or two load cells to indicate and monitor web tension by amplifying the load cell signal. ...

Voltage: 12 V
Current: 35 mA

... Twisted-pair transmitter in miniature housing with angular BNC-plug for direct connection to any video camera. Applicable for colour or monochrome signals. Transmission distance under optimal conditions max. 1200 m with 0.6 mm^2 twisted pair cable. ...

Voltage: 85 V - 265 V

... Continuous on-line monitoring of rotating equipment Description: The modular programmable CEC 8000 Computer-Controlled Amplifier/ Tracking System (C-CATS) offers more power and greater flexibility than ever. It provides continuous online ...

Power: 10 W

... without band switching or swapping narrow band amplifiers resulting in faster and more accurate testing. The amplifier can be used in wireless communications and component testing wherever a highly linear amplifier ...

... The Manner sensor signal amplifier captures the measuring signal from the rotating sensors. In addition to DMS sensors, other sensors such as thermocouple elements, PT 100, Hall, piezo and Micro-Epsilon sensors and potentiometers can ...

Power: 2 kW - 3 kW

... feature sets as the GEN IV, but utilizing traditional klystron technology. The Ka-Band EIK amplifier provides up to 800 watts of Ka-band power. All amplifiers are available as single units or in redundant or combined ...