{{product.productLabel}} {{product.model}}
{{#if product.featureValues}}{{product.productPrice.formattedPrice}} {{#if product.productPrice.priceType === "PRICE_RANGE" }} - {{product.productPrice.formattedPriceMax}} {{/if}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{product.productLabel}} {{product.model}}
{{#if product.featureValues}}{{product.productPrice.formattedPrice}} {{#if product.productPrice.priceType === "PRICE_RANGE" }} - {{product.productPrice.formattedPriceMax}} {{/if}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
With the S15C, Modbus and analog sensors can now be used to communicate via IO-Link and deliver the data you need for predictive maintenance and operational improvements. • Modbus Sensors Converters: Vibration and Temperature, Temperature ...
This compact T-connector brings a non-ISD enabled device into an ISD system. • Connects conventional emergency stop buttons or safe mechanical switch contacts to an ISD chain of devices • Rugged design rated up to IP67 installs easily, ...
MWE485-TDM can convert a RS232 serial port signal to three wires high speed semi duplex RS485 or a four wires full duplex RS422 signal, with 2500V optical isolation between the signal and the power. The main function is to realize the ...
USB - RS485 interface converter The interface converter code MCIUSB485 is used to connect to a PC, PLC or supervision system with USB interface, up to 32 measuring instruments or other devices* with RS485 interface, with any protocol ...
The Wi-CAN device is connected to the CANBus line over the wireless network and is used to access the information of the connected devices, set parameters and update the software. There must be a wireless internet network in the environment ...
The Delocan device is a single-channel high-speed CANBus-USB interface. It offers easy, powerful and versatile communication between your Delocan computer and the CANBus line. It converts the messages from the CANBus analyzer to CAN communication ...
Industrial Serial to Fiber Media Converter • - Supports Multi-mode 2KM, Single-mode 30KM • - PTP and Ring mode for serial fiber ring communication • - Supports RS-485 120 ohm line terminator • - Supports RS-485 Data signals pull high/low ...
Atop Technologies
The MX200-TTX is an interface converter deployed at the edge of a G703 E1/T1 line or network providing a point-to-point interconnection for voice with an E1/T1, LAN with a powerful 10/100BaseT bridge and miscellaneous applications with ...
CXR Networks
SINGLE CHANNEL RS 422 / RS 485 ISOLATING REPEATER DESCRIPTION The D1061S is used to separate Intrinsically Safe RS 422 / RS 485 equipment located in Hazardous Location from a RS 422 / RS 485 / RS 232 controller located in Safe Area. ...
The ProfiHub F1 is used to convert PROFIBUS-fieldbus network signals from copper to fiber optics. It should be installed on a DIN Rail. The device can work as a ring module or in a line or point-to-point structure. If a message is received ...
High Voltage Direct Current (HVDC) systems enable utilities to move more power further, efficiently integrate renewables, interconnect grids, and improve network performance. HVDC systems utilize power electronics technology to convert ...
The CS4354 is a 24-bit, 192 kHz stereo audio digital/analog converter (DAC) with a 101 dB dynamic range and on-chip 2 VRMS line driver working from a single 5 V power supply. Based on a charge-pump architecture, this IC outputs a 2 VRMS ...
Cirrus Logic
● Rich communication interface types ● Supports 2.5G/3G/4G/NB-IoT cellular networks ● High-performance hardware platform ● Support remote management, deliver on-line communication protocols, and reduce on-site maintenance costs
The WC-Series of Wavelength Converters interfaces the 1310 nm –short-haul data transmission equipment to 1550 nm amplified systems for long haul transmission. The line transmitters and receivers of the WC-Series have been designed ...
The DM-232TO485 communication line converter is available for 35 mm rail mounting. The converter supports both automated and controlled switching of transfer direction with maximum transmission rate of 115 kBd. The line direction RS485 ...
AMiT, spol. s r.o.
The FOI-2172 and FOI-2173 both provide complete electrical isolation for composite video and audio communications. The units are compatible with NTSC, PAL, and SECAM video broadcast standards. The units are transparent to all monochrome ...
FiberPlex Technologies, LLC
the only photovoltaic power converter (PPC) product line capable of delivering a wide range of power and voltage outputs. Power output levels range from tens of milliwatts to over 3 watts, while output voltage levels are possible from ...
Provides four (4) ±190Vdc line powering RFT-V channels with current limiting and ground fault protection Wide AC input range (90-307V) for worldwide deployments High efficiency for reduced OPEX and carbon footprint Optional integrated ...
The TCC 165, 168, 169, 170, 171 charge converters are airborne devices specifically designed for very high temperature piezoelectric transducers. They have a reinforced charge amplifier front end, and a biased output voltage proportional ...
Indumart ITP215Current to Pressure (I/P) Converter produces a pressure output signal directly proportional to its 4-20 mAcurrent input. Premium grade and precision electronic components are used throughout this instrument to assure excellent ...
The QV/02 is part of a range of in-line converters providing charge/voltage conversion when supplied with a standard IEPE supply current in the range of 2 to 20mA. The low impedance line drive maintains signal integrity even over distances ...
The QV/04 is part of a range of in-line converters providing charge/voltage conversion when supplied with a standard IEPE supply current in the range of 2 to 20mA. The low impedance line drive maintains signal integrity even over distances ...
Please specify:
Help us improve:
remaining