Flow: 460 l/min
Head: 39 m
Power: 0.18 kW - 5.5 kW
... centrifugal pump. All parts that are in contact with the medium are made solid of stainless steel (1.4581). The cooling and lubrication of the mechanical seals is carried out through a separate seal water circle. Advantages ...
Pressure: 63 bar
Power: 0.18, 0.12 kW
Fluid temperature: -10 °C - 60 °C
... The pump is designed for the lubrication with plastic grease or oil of machines and equipment requiring continuous lubrication in small quantities. The lubricant is ...
Zaklady Automatyki POLNA S.A.
... 1 pneumatic pump is a single-acting pump suitable for all types of applications. The maximum amount of grease supplied during every pumping cycle is 30 cm³ (an amount that is approximately sufficient for 100 lubrication ...
Pressure: 275 bar
... Ideally suitable for the automatic grease lubrication of all types of industrial machines and as a chassis lubrication pump for trucks, trailers, buses, construction and mechanical handling vehicles. ...
I.L.C. srl
Flow: 4.9 m³/h - 235.7 m³/h
Pressure: 4 bar - 24 bar
Power: 2.2 kW - 45 kW
... carried out on-site without the need to remove the pump from its installation. This significantly reduces downtime and optimizes the productivity of industrial operations. The PCM EcoMoineau™ MX pump is the ideal choice ...
... device that completes the lubrication cycle and ensures that the lubricant does not drip. MIXER-Mecos Minimal Quantity Lubrication Pumps are used in: The Mixer modular system is ...
SOATO FLUID SYSTEM
Flow: 0.01 l/min
Pressure: 20 MPa
Power: 24 W
... cartridges. ● Be careful not to let air enter the pump when replacing the cartridge. ● After greasing or after replacing the cartridge, be sure to open the air vent plug and vent the air inside the pump. ...
... PM-10 Series Manual Cyclic Pumps are used in applications where a fixed output of lubricant is desired. With the PM-10 Series, the leverage of the pump handle enables the unit to deliver ...
Pressure: 1.7 bar - 3 bar
Length: 85, 132 mm
Width: 72, 99 mm
... Volumetric manual pump; each activation tallies with the pre-set quantity of lubricant. The lubricant is delivered by a plunger piston driven by a mechanical spring, suitably sized and preloaded. Tank ...
Azeta Zeo Asioli
Flow: 0.25 m³/h - 1,300 m³/h
Head: 3 m - 230 m
Fluid temperature: -100 °C - 350 °C
... Stainless Steel Magnetic Drive Chemical Process Pump Discover here the advantages of the MKP from CP – The highly reliable centrifugal pump for various applications. Overview Special features Up to 30% solids ...
Flow: 0.15 m³/h - 13.5 m³/h
... Lubrication Oil Gear Pump Fluid Tech Systems offer “ROTOFLUID” brand gear pump Model “FTX” (Gear Pump, Lubrication Oil Gear Pump) which is most efficient ...
Fluid Tech Systems
... ARSA series units are the ideal solution for residual dry chamber installations. They have the same performance as the ARS pumps, but with the advantage of being outside the reservoir of the liquid to be pumped, they use standard IEC ...
Bombas Ideal
... Self-contained and sealed oil bucket pumps with a 20-liter capacity. These pumps are completely sealed to the oil container preventing any contamination or spillage. ...
Yamada Corporation
Flow: 0.0032 m³/h - 0.026 m³/h
... hydraulic fluid and gear lubricant make possible the use of the best medium for hydraulic diaphragm pulsing and the best medium for gear lubrication. The results are better pump performance and longer ...
JAECO Fluid Systems
... Flexibility – Manual operation option available so pump can be used as a back up to main pump or in low volume lab applications. AIR FLOW dictates how fast the pump can cycle and hence ...
Flow: 0.1 l/min - 2,400 l/min
Fluid temperature: -30 °C - 150 °C
... equipment calls for reliable components. Whether in lubrication oil applications or in processing plants, a pump is required to work reliably and longlasting. Thanks to the extensive range of components and pump ...
Maag Germany GmbH
Flow: 100 m³/h - 20,000 m³/h
Pressure: 145 bar
Head: 10 m - 1,200 m
... The ZM pump is designed for stringent demands in process and transfer services. Engineered to comply with the latest edition of API 610, these horizontal pumps with double suction impeller and a between bearing design ...
RUHRPUMPEN
Flow: 21 m³/h
Pressure: 25 bar
... the replaceable shaft sleeve. The lubrication of all parts in the pump is automatically achieved by using the conveying medium when the pump works. The four bearing sleeves in the pump ...
Hebei Hengsheng Pumps Co., Ltd.
Flow: 1,135 l/min
Pressure: 0 bar - 400 bar
... Heavy duty reciprocating pumps with vacuum jacketed cold end Available in simplex and triplex execution with oil lubricated crank drive or geared motor Suitable for intermittent or continuous duty ...
Flow: 10.5 l/s - 400 l/s
Head: 25.4 m - 94.2 m
... ZGB(P) slurry pumps is horizontal cantilever single-stage, single-suction, double-case and high head of delivery centrifugal slurry pump. Series ZGB(P) UP-to-date generation Slurry Pump with large ...
Pressure: 400 bar
... 81818/P Air-operated pumps for dispensing grease at short distances or for forced lubrication. Compression ratio 50:1. 16 kg drums ...
Ompi Srl
Flow: 20 m³/h - 500 m³/h
Pressure: 10 bar
Head: 10 m - 30 m
... of waste can be pump depending on the impeller structure. • This series can be coupled with diesel engine and high-efficiency IE2 or IE3 (Optional) class electric motor. • Thanks to back pull out design, the rotating parts of the pump are ...
MAS - DAF
Flow: 0 us gal/min - 12 us gal/min
Weight: 3.9 kg
... double-diaphragm (AODD) pump for reliable use in lubrication, tire filling, adhesive dispensing, OEM systems and many more industrial applications. Featuring a patented non-stalling, lubrication-free ...
Flow: 0 m³/h - 200 m³/h
Pressure: 12 MPa
Fluid temperature: 0 °C - 40 °C
... Piston Pump Mine and oilfield pumps Overview Widely used for conveying the particulate abrasive medium material such as pulp, slurry, coal slurry and so on in the industries on mining, thermal power plants, metallurgy, ...
the best suppliers