... efficiency, it is not recommended to use a simple air- oil heat exchanger. In such cases it is useful to feed the air- oil exchanger with an off-line pump, to make it independent from the primary oleo hydraulic ...
Power: 3,460, 5,300, 8,150 W
Maximum temperature: 25 °C - 40 °C
Flow rate: 10, 14, 25 l/min
... control and display. • Chiller malfunction signal display (except for ACW-LP 12 model and for optional features in other single-phase models). • High efficiency heat exchangers. • Low-noise axial fans. • Bypass on the hydraulic ...
... Standard Oil Coolers. Power supply AC - DC - Hydraulic. ...
Oesse
The heat exchanger installed in the continuous recooling unit is easy to open for cleaning when dealing with heavily contaminated media. The air intake for the condenser can be optionally supplied with an air filter. The units come as standard with 1 ...
Flow rate: 400 l/min
... A fixed tube sheet design makes tube side cleaning easy. The oil is not very dirty but the coolant is very dirty, so the oil cooler is best suited in areas where the tube side is often ...
TAISEI KOGYO
Maximum temperature: 180, 120 °C
... also refurbish your bearing oil cooler for easy maintenance by changing the configuration (number of sections) of your cooler. There are two families of bearing coolers : internal and ...
Thermofin
Power: 3.3 kW - 3.9 kW
Maximum temperature: -10 °C - 45 °C
Flow rate: 24.3, 29.1 l/min
... synchronization type and temperature fixture type Precise control of the oil temperature up to 45℃ Power Supply - 3P 230V 50Hz Available Oil - Lubricating oil, Hydraulic operating ...
Power: 0.9, 0.76, 0.35 kW
Maximum temperature: 0 °C - 35 °C
Flow rate: 10 l/min
... Chiller, in the industry is divided into air-cooled chiller and water-cooled chiller, chiller in temperature control is divided into low-temperature chiller and room temperature chiller, room temperature ...
... Fan/coil unit specifically designed to cool transformer oil. Transformer Oil Coolers are specifically designed for the transformer make and model, and the operating conditions. Each cooler ...
... consumption Application: Especially suited for cooling of lube oil and hydraulic oil in engines, transmission. Also used in the plastic machinery industry. ...
Power: 2 kW - 52 kW
Maximum temperature: 20 °C - 35 °C
... RACA OIL are chillers regulating the cutting fluid emulsions used in boring machines, grinding press machines, wire drawing machines, where oil shall be kept at a certain temperature ...
... Oil coolers ES series are designed for optimum cooling with poor heat transfer fluids such as oil and Ethylene Glycol/Water (EGW) mixture. Our oil coolers provide up ...
... pressure switches • Low oil pressure switch • Oil flow control regulator. • Evaporator AISI 316 stainless steel platehigh oil-gas exchange coefficient. • Axial fan, centrifugal fans ...
... Our oil coolers are system components for the safe operation of screw compressors. For each application BITZER offers the right oil cooler air- or water-cooled, for HCFCs and chlorine-free ...
Power: 2,000 W - 170,000 W
Maximum temperature: 5 °C - 45 °C
Power: 1.8 W - 15 W
Maximum temperature: 5 °C - 50 °C
... Immersion type oil cooling units for cutting/grinding liquid that achieve high energy saving rates, low noise, and high-accuracy temperature control. ...
... . The sealing rubber ring shall be replaced at the same time; ◘ The engine is forbidden to work without an oil cooler or when the oil cooler fails. ◘ Weichai provides quality assurance ...
Maximum temperature: 200 °C
... mm. Characteristics : - hard chrome plated , grind machined and mirror finishing polished roll - a double spiral oil circulation ensures a perfect homogeneity of the surface temperature - a brushless motor unit drive ensures ...
Flow rate: 10 l/min - 30 l/min
Pressure: 30 bar
... Hot fluid inlet max. temperature: 225°C • Cold fluid inlet min. temperature: -160°C Operating fluids: -Mineral oil -Synthetic oil -Emulsified water -Water - Ethylene glycol ADVANTAGES: • Compact and light ...
Taon Hydraulik Komponenter ApS
Flow rate: 40 l/min - 120 l/min
Pressure: 30 bar
... Hot fluid inlet max. temperature: 225°C • Cold fluid inlet min. temperature: -160°C Operating fluids: -Mineral oil -Synthetic oil -Emulsified water -Water - Ethylene glycol ADVANTAGES: • Compact and light ...
Taon Hydraulik Komponenter ApS
Flow rate: 30 l/min - 80 l/min
Pressure: 12 bar
They consist of smooth tubes with little diameter; this allows the best compromise between high thermic performance and low pressure drops.
Taon Hydraulik Komponenter ApS
... Coolant chillers are essential to your machining operation. Metalworking fluids must be maintained at a constant and correct temperature for your application to ensure you produce consistent high-quality parts. Quality ...
Power: 4.4 kW - 28.8 kW
Flow rate: 5 l/min - 320 l/min
Pressure: 26 bar
... International air/ oil coolers are made of aluminum to achieve high resistance to operating pressure and greater heat exchange capacity, all in very compact dimensions. They can be used for hydraulic ...
... It is used for cooling hydraulic fluid, improving working condition, extending working hours and operating life. ...
... Steel series coolers are normally used to cool hydraulic circuits and installed on return pipes: they must be protected from mechanical shocks and vibrations by supports and must be connected to the circuit by flexible ...
the best suppliers