|
|
Each product is galvanically isolated up 6 ways with 1,5 KVac. The most important features are its incredible speed, 1 ms for the digital modules and 20 ms for the analog ones, and its high accuracy, around 0,01%. Easily configurable through EDS sheets that you can download from the website www.seneca.it
Suitable for the Automotive field and all the applications where is required the best speed and accuracy for a perfect control of your machine.
Seneca offer a Wide range of Canopen Modules & Control Unit:
- 16 CH digital input / 8 CH digital output CANopen
- 24 CH digital input CANopen
- 24 CH digital output CANopen
- 3 CH analog output (mA, V) CANopen module
- 4 Ch RTD (P100, Ni100, Pt500, Pt1000) input CANopen module
- 8 CH analog input (mA, V) CANopen module
- 8 CH Thermocouple (J,K,E,N,S,R,B,T) CANopen module
- 1 CH strain gauge CANopen module
- Multi-function control unit. CAN, Ethernet, RS232/RS485, ModBUS RTU integrated ports
|
|
|
WAGO-SPEEDWAY 767 the new performance class for automation without control cabinets. Bus linking will be implemented by means of fieldbus couplers and programmable fieldbus couplers for PROFIBUS DP, EtherNet and CANopen, including PROFINET and DeviceNet fieldbus couplers. The modules already come equipped with eight digital inputs. Input and output modules complement the couplers. All of the digital modules are equipped with eight channels, with M8 or M12 connections available. The product program also includes two input modules and four output modules for rated currents of 0.5 and 2 A.
|
|
Typical Distributed I/O and Remote I/O Applications
Distributed I/O and Remote I/O eliminate expensive point-to-point wires by networking just a few, or thousands of, process signals onto one digital communication link.
For data acquisition, distributed I/O and remote I/O send signals from field-mounted sensors, transmitters, transducers, and alarms directly to DCS, PLC, and PC-based systems.
Send control signals long distances to remote valves, pumps, and motors with distributed I/O and remote I/O.
Unburden an overworked computer system by distributing signal conditioning and intelligence.
Use as expansion I/O to add points to a DCS or PLC system.
Convert weak sensor signals to immune digital signals to avoid damage during long-distance transmission through a noisy plant.
Distributed I/O and Remote I/O allow the transmission of signals any distance and over any terrain with twisted-pair wires, fiber optics, radio link, or modems.
|
|
|
These I/O blocks are ideal for dry applications where the block can reside either in a control cabinet or on machine in an out of the way location.
|
|
On-Machine control is the placement of automation components directly on a machine rather than housing them in a remote, central cabinet. This is possible with the emergence of more modular, compact devices, plug-and-play connectivity, flexible communication networks, intelligent devices, and a wide array of products with improved environmental ratings. On-Machine components can include everything from programmable controllers, motor starters, drives, sensors, contactors, network media, distribution boxes, and I/O, as well as HMI devices. On-Machine solutions provide reduced wiring and system costs, improved Mean Time to Repair (MTTR), enhanced control system reliability, increased productivity, and greater flexibility.
|
|
On-Machine control is the placement of automation components directly on a machine rather than housing them in a remote, central cabinet. This is possible with the emergence of more modular, compact devices, plug-and-play connectivity, flexible communication networks, intelligent devices, and a wide array of products with improved environmental ratings. On-Machine components can include everything from programmable controllers, motor starters, drives, sensors, contactors, network media, distribution boxes, and I/O, as well as HMI devices. On-Machine solutions provide reduced wiring and system costs, improved Mean Time to Repair (MTTR), enhanced control system reliability, increased productivity, and greater flexibility.
|
|
The intelligent Ethernet I/O modules MSX-Exxxx are especially suited for industrial measurement, control and regulation tasks very close to the test item.
- ARM9 technology: intelligent system
- All modules can be cascaded and synchronized in the ìs range
- Degree of protection IP 65 or IP 40
- Extented temperature range: 40 °C / + 85 °C
Functions:
- Digital I/O module
- Multifunction counter modules for incremental or sin/cos signal generator
- Analog I/O module
- Module for length measurement
- Module for synchronous length measurement
Easy connection to PLC:
The intelligent modules can be connected fast and easily to PLCs without any programming skills.
|
|
Semaphore offers a new range of affordable Ethernet Remote Modules of compact size and monoblock construction that can be fixed easily on DIN rail.
The modules connect a wide variety of electrical, electronic, and mechanical devices and sensors -- such as pumps, temperature and pressure transmitters, motors, and more — to computers and applications over standard Ethernet networks (Modbus/TCP), RS485 (Modbus RTU), or other controllers and PLCs.
Each remote I/O module has its own Ethernet Modbus TCP/IP port making it easy to connect the modules to each other with up to 100 meters of CAT5 cable, or even longer distances using fiber optic switches.
There are several types of Ethernet remote I/O modules available with different I/O formats.
|
|
|
|
|
|
ALTO RANGE
1/ HARDWARE PRESENTATION
Sturdy aluminium case.
Compact product : Width x Height x Depth = 128 x 145 x 72 mm
IP30
Disconnectable connectors.
A descriptive label and a LED per input/ouput.
Voltage : 24Vdc; 12Vdc (some models on demand) ; 85-264Vac (some models on demand)
Electromagnetic immunity EN50081-2
Operating temperature : -20°C +70°C
MTBF : 12 years min according to UTE2000 45°C
Quick anchoring clip on DIN symmetrical rail.
Communications
* 1 Ethernet 10 base T Channel
* 1 RS232/RS485 channnel
* 1 RS232 channel
* Digital inputs with sensor wire control : 4 informations per input : Normal open, normal close, open failure, short circuit.
* Digital static output : Type P, 500mA, redundant command
* Digital relay output : 1 contact single pole normally open; Coil 24V; 3A on resistive load, 2A on inductive load
* Tension analog input : +-100mV , +-1V , +-10V
* Current analog input : +-20mA ; 4-20mA
* PT100, PT1000
* Thermo couple : B C E J K N R S T
* Analog outputs : 0-20mA or 0-10V , 12 bits
2/ SOFTWARE USES : 2 possibilities
ALTO WEBIO
Alto webIO is a smart remote input output module. It needn't workbench for start up. It a Modbus TCP slave with a embedded HTTP server.
The menu allows
* to configure the products (server adresses, email wording, passwords, ...)
* to display input states on line
* to force outputs for test
* to configure filtering of inputs, blinking of outputs
* to configure withdrawn output positions if ethernet communication failure
ALTO ISAGRAF : IEC113163 programming
With the Isagraf workbench, ALTO Isagraf becomes a microPLC
It uses the IEC61131-3 languages.
|
|
|
|
|
|
Daisy-chained Ethernet I/O Connection
A new daisy-chained Ethernet I/O paradigm is now available. The ioLogik E1200 series industrial remote Ethernet I/O has two embedded Ethernet switch ports that allow information to flow to another local Ethernet device or connect to the next ioLogik in the daisy-chain. Applications such as factory automation, security and surveillance systems, and tunnel monitoring, can make use of daisy-chained Ethernet for building multi-drop I/O networks over standard Ethernet cables. Many industrial automation users are familiar with the multi-drop configuration typically used in fieldbus applications. The daisy-chain function on the remote Ethernet I/O ioLogik E1200 not only increases the connection between machines and panels, but also lowers the cost of buying separate Ethernet switches, and at the same time reduces labor fees and cabling by a large percentage.
Features:
•Built-in 2-port Ethernet switch for daisy-chain topologies
•Free support of Moxa’s push-based Active OPC Server Lite
- Seamlessly connect to any SCADA system
- Save 80% on network bandwidth
- I/O response that’s seven times faster
•User-defined Modbus/TCP addressing
•MXIO programming library for Windows and WinCE VB/VC.NET and Linux C APIs
•Web configuration with Import/Export function
|
|
APPLICATIONS :
Inputs/Outputs management over Ethernet. Functions : alarms, counters, and so on.
MANAGEMENT
Configuration and management over RS232 and Ethernet interfaces - TCP/IP.
PROTOCOLS :
- HTTP
- TCP/UDP
- SNMP
- ALARMS
- SNMPtraps
- TCP/UDP
- SMTP (Email)
The alarm conditions can be configured on inputs or counters states.
|
|
User can select
32 Input / Output / Latch function per each I/O point
(photocoupler isolation)
Remote I/O by Ethernet Interface
Reducing the wiring of FA machines
|
|
|
Expandable I/O, using 5 different I/O cards. Many I/O expansion cards can be attached to same device. I/O expands max. 72AI, 34AO, 72DI, 72DO/64RO. Two serial ports, one which supports AL Serial Plug-in modules.
|
|
MAXIFLEX is a versatile and powerful telemetry and remote I/O system suitable for a wide range of applications from RTU Outstations to Remote I/O on your DCS or SCADA software.
Ease of use and powerful communications capability are the hall-mark of this range.
It is true that plant communications technology has advanced dramatically in the last decade. The range of instrumentation capable of being networked grows daily.
|
|
Field Bus System - Zone 1 mounting
Plug-in modules installed in field housing IP66 certified
Intelligent combination of hazardous area protection methods
Encapsulated modules for rough environment
Installation in zone 1 in polyester or stainless steel housing
Binary, analogue, RTD100, TC, voltage, frequency signals
24 Vdc, 110 Vac and 230 Vac power supplies
Modules 2 to 8 channels for binary signals (single or multichannels modules)
Modules 1 to 4 channels for analogue signals
Up to 96 analogue signals and 192 digital signals on the same remote I/O station
Interfaces for Eex d devices
Eex i et Eex e can be mixed on the same unit
No hot work permit required for maintenance
|
|
|
|
|
|
With the IS1 R. STAHL present the second generation of Remote I/O Systems with intrinsically safe inputs and outputs.
IS1 is extremely simple to use: A CPU & Power Module and several input/output modules are snapped on to the BusRail (35 mm DIN rail). The unique PowerBus power supply concept, developed especially for use in hazardous areas, makes system planning as simple as for normal industrial I/O systems.
IS1 is particularly flexible: It can be used for small and large signal quantities with the possibility of installing field stations in Zone 1 / Division 1 or Zone 2 / Division 2. Installation in control rooms is also possible. An intrinsically safe fieldbus using copper-wire or fibre-optic technology connects field stations in Zone 1 with the automation devices.
IS1 is extremely economical: Modules with 8 or 16 inputs lower the price per signal. The optional ServiceBus in connection with the "I.S. Wizard" software or a HART-Management System cuts down the time for commissioning, trouble shooting and maintenance.
The new I/O modules for Zone 2 applications can be mixed with the Zone 1 modules on the same BusRail. With this it is possible to design very cost effective field stations. IS1 is now available with Industrial Ethernet / Modbus TCP interface.
Modular Remote I/O System for 35 mm DIN rail mounting:
Installation in Zone 1 / Division 1 or Zone 2 / Division 2, Zone 21 and Zone 22, safe areas
Fieldbus communication: Modbus RTU, Profibus DP V0 and P V1 HART, Industrial Ethernet
Hot swap for all modules
Redundant internal system bus
Full redundancy (many control systems) or line redundancy (all control systems)
Field enclosures in many versions
|
|
|
|
|
|
S900 provides all input and output modules needed for intrinsically safe field signal connection. The field signals are amplified in every S900 functional module, electrically isolated, and then output via an internal serial bus. A communication interface converts the digitized signals to adapt them to the standardized PROFIBUS DPV1 fieldbus protocol. Supervisory process control systems, DCS or SCADA systems use an intrinsically safe fieldbus to communicate with the communication interface.
A single fieldbus network suffices for configuring the individual fieldbus nodes, for cyclic data exchange, for all acyclic services, and for communication with HART®-compatible field instruments. All functional modules can be replaced easily and quickly in the installation or maintenance phase. The functional modules and the - optionally redundant - communication interfaces of systems placed in Zone 1 can be removed and plugged in while operation is running, without affecting the communication of the remaining modules. Only the primary power for the plug-in type power supply modules requires increased safety EEx-e.
Integrated encapsulated switch-off mechanisms allow for hotswapping, i.e. the power supply units can be replaced without interrupting the primary power. Due to its little space requirements and robust design and its environmentally ruggedized case, the I/O system S900 is the best, cost-saving solution for use on site, in hazardous Zone 1 or Zone 2 areas.
|
|
Description
This module allows the connection of 16 digital signals to the PROFIBUS-DP, according to DIN EN 61158-2...6; DIN EN 61784-1, within the hazardous area. Signals from flameproof encapsulated limit switches and control devices can be injected directly.
In case of NAMUR sensors or other signalling contacts that are controlled in an intrinsically safe way, barriers or isolator amplifiers are connected on line side. LEDs on the front of the module output the input states as well as important status messages.
|
|
Description
This module allows the connection of 16 digital signals to the PROFIBUS-DP, according to DIN EN 61158-2...6; DIN EN 61784-1, within the hazardous area. Signals from flameproof encapsulated limit switches and control devices can be injected directly.
In case of NAMUR sensors or other signalling contacts that are controlled in an intrinsically safe way, barriers or isolator amplifiers are connected on line side. LEDs on the front of the module output the input states as well as important status messages.
|
|
|
|
|
|
Ascon’s Deltadue modules include
· analogue and digital I/O
· single and dual loop PID controller
· transmitter
· gateway
· WebSCADA
Applications include the use as complete control systems, multi loop PID controllers, I/Os, field interfaces of PC based systems, integration of PLC for any process or machine such as extruders, furnaces, kilns, cold rooms
Features include: universal inputs (Pt100, T/C, mA, mV, current transformer); digital I/Os; PID algorithm; heat/cool PID; Auto tuning; Set point management; universal control outputs (mA, relay, SSR); PWM and built-in RS485 Modbus RTU
Control system architectures can be realized by connecting the modules to
· a PLC or SCADA with MODBUS TCP via an Ethernet network or the web
· any web browser for the configuration of HTML management pages and to MODBUS TCP SCADAs via an Ethernet network
· a MODBUS TCP SCADA (via an Ethernet network) and to a PLC (PROFIBUS DP or MODBUS RTU or DeviceNet) simultaneously
· CANopen, PROFIBUS DP, DeviceNet networks
· MODBUS RTU networks with different baud rate, parity and stop bits
· two masters, such as Operator Panels, SCADA, PACs, simultaneously
Modules work as independent units
The optional Manager module provides
· automatic learning and back-up of the configuration data of the modules
· Hot Swapping to maximize process uptime
· automatic configuration of replaced modules to reduce machine downtime. While failed module is replaced, the other modules work normally
· offline configuration to simplify start-up. When the modules are inserted, they are recognised, configured and parameters downloaded
· diagnostics
|
|
|
Our modular Remote I/O systems - RPI, LB and FB - are the cost-effective connection of your field signals in the hazardous and the safe areas to your process control system via the fieldbus. A variety of gateways are available for the connection to different fieldbusses. Free combinable I/O modules and high modularity offers cost-saving installations. The systems are characterized by high functionality and simple handling.
|
|
The ISbus fieldbus system product series includes components and systems for use on Profibus PA and FOUNDATION fieldbus H1
Installation in Zone 1, Zone 2, Zone 21, Zone 22 and Division 2
Different field device couplers to connect intrinsically safe and non-intrinsically safe fieldbus
Integration of simple, binary signals in the fieldbus via intelligent digital I/O couplers
Redundant fieldbus power supply with galvanic isolation of fieldbus segments for FOUNDATION fieldbus H1
Field housings of different sizes and materials, such as plastic, stainless steel and aluminium
System solutions for field installations and integrated solutions in combination with remote I/O
|
|
|
|
|
|
Multifunctional I/O interface suitable for industrial process control,
building automation and complex domotic system
Featuring a standard Modbus protocol, the MXC700 module can be remotely controlled by any Modbus master, like operator terminals or PLC and it is compatible with the most famous HMI/SCADA software available on the market .
MXC700BIO is the easiest way to implement reliable but economical distributed systems for control and acquisition of plant data.
Also, up to 31 MXC700BIO modules can be connected on the same bus allowing to build even larger systems with more I/O as needed.
Each of the 48 digital outputs is capable of sourcing up to 0.7 Amps and all outputs are short circuit and overtemperature protected.
The inputs may be used to read dry contacts and push buttons (a debounce filter is present) or for counting applications, up to 100 pulses/second.
A dedicated input for fast counting applications
(up to 10 kHz) is also present.
The two D/A outputs and the two A/D inputs for 0-10V signals with 12 bit resolutions complete the features of this versatile I/O module.
* RS485 Serial interface with Modbus protocol
* 48 digital outputs, optocoupled,
* for loads up to 0.7A at 24Vdc
* 24 optocoupled inputs, ESD protected
* 2 analog inputs, 0-10V with 12 bit resolution
* 2 analog outputs, 0-10V with 12 bit resolution
* 1 input for encoder fast counting, up to 10 kHz
* 2 analog inputs with resolution up to 24 bit for load cells, 4 : 20 mA or 0 -10 V sensors (optional)
|
|
|
|
|
|
RIO – (Remote Input Output) is a compact modular system of remote I/Omodules available from OSAI for the management and control, through a field bus, of inputs and outputs distributed throughout the plant.
The modular structure of each RIO block guarantees a high degree of flexibility to reduce installation and maintenance costs. In the event of a malfunction, the electronic section of any block can easily be replaced without having to disconnect cables. The status of each input and output on every block is displayed with a LED indicator. External cables are easily connented by inserting wires into simple contact blocks thus avoiding the inconvenience and uncertainty associated with traditional screw terminals.
All units use a simple “snap on” connection to the DIN support rail connected to the bus coupler so that a series of RIO blocks (digital, analogue and intelligent), can be installed in a variety of combinations.
RIO bus coupler : is an interface unit that connects the RIO blocks to the bus. It manages up to 8 modules.
RIO I/O MODULES.
Digital versions:
- RIO 16 I /Kes - 16 Input module
- RIO 16 O /KEs - 16 Output module
- RIO 8 I/O - 8 I/O configurable module
- RIO 8I 8I/O /KEs - 8 Input + 8 I/O configurable module.
Analogical versions:
- RIO 4AI ±10V - 4 analogue input module (+-10Vdc)
- RIO 4AI 20mA - 4 analogue input module (0-20mA)
- RIO 4AI/4AO ±10V - 4 input + 4 analogue output module (+-10Vdc)
- RIO 4AI/4AO 20mA - 4 input + 4 analogue output module (0-20mA)
|
|
|
Foundation Fieldbus H1 level has been designed as a digital replacement of the 4 to 20mA standard in the process industries. Foundation Fieldbus is also a LAN (Local Area Network) for instruments used in both process and manufacturing automation with built-in capability to distribute the control application across the network. The physical wiring is also fully compatible with intrinsic safety (IS) or nonincendive wiring standards and may be used in hazardous, as well as general purpose areas. In hazardous areas standard explosion-proofing or power limited concepts may be used, as well as IS concepts, offering greater cabling design flexibility.
|
|
|
Open, smart and seamless. Omron offers open networks such as DeviceNet and PROFIBUS-DP that allow easy integration in existing installations and ensure compatibility with third party systems. We also offer Compobus/S, Omron proprietary sensor/actuator bus, for cost efficient, fast and program-less configuration.
|
|
A complete range of extension modules for Touch PLCs: EXM modules range:
- 4 digital outputs modules
- 2 digital inputs modules
- 2 digital inputs/outputs modules
- 8 analog and temperature modules.
EXM range: 16 add-on modules for Touch PLCs.
Flow, pressure, temperature, speed, cadence, level,...
Pro-face : a wide range of Touch PLCs (4"..12", colour TFT/STN or monochrome, various interfaces: Ethernet, USB, cf-card, etc...),
DIO or on CANopen / Flex networks.
|
|
Analog Input & I/O
12-bit or less resolution
14 and 16 bit resolution
Analog Output
12-bit or less resolution
Digital I/O
Counter-Timer
Parallel
Special purpose
Serial Communications
LPT Port and 2
|
|
Analog Input & I/O
12-bit or less resolution
14 and 16 bit resolution
Analog Output
12-bit or less resolution
Digital I/O
Parallel
Quadrature Encoders and Interrupts
|
|
Analog I/O
12-bit or less resolution
14 and 16 bit resolution
Temperature
Analog Output
12 bit or less resolution
14 and 16 bit resolution
Digital I/O
Counter-Timer
High Voltage
Parallel
Quadrature Encoders and Interrupts
Serial Communications
16 Port
4-8 Port
Single & Dual Port
|
|
|
|
I/O modules
