loading in progress... Please wait

I/O modules

Advantech provides two different types of controllers with respective I/O modules for versatile applications, PC-based Controllers and Programmable Automation Controllers (PAC). The PC-based controllers are open development environment interface; the PACs are a single platform with multi-disciplined controller functionalities.

I/O module BRAINCHILD ELECTRONIC

Data Acquisition modules/ Distributed IO modules for SCADA / PLC/HMI

Good features:

- Portable
- Modbus connectivity
- Simple setup and easy handling
- Upto 128 Modules on RS485 network
- Isolated modules available for special applications
- Low-cost IO modules addition to existing PLC system
- Standard software for module configuration and trouble shooting
- Data acquisition software for data storage and Real-time analysis on PC
- IO modules used with the third party softwares via Modbus RTU Protocol
- Interface with field devices to provide real-time data for SCADA/PLC/HMI
- LEDs on every module for digital IO status, communication and power supply
- Different types of IO Modules AI, AO, DI, DO, RTD, Thermocouples all available
- Direct reading of temperature without scaling by using RTD and Thermocouple Modules

I/O module Baumer
AS-Interface

The solution Interface-HAVE is an alternative to the parallel beams of cables. It is the only system which can transfer the data and energy by means of one only cable with 2 drivers coded with protection against the inversion from polarity. The connection of the detectors and the actuateurs is carried out by the technique of perforation of the insulation.

I/O module Bosch Rexroth Electric Drives and Controls

Modular, Scalable I/O System in IP20

This I/O system offers complete scalability, easy wiring and powerful diagnostics. Choose from the following interfaces: PROFIBUS-DP, INTERBUS, DeviceNet or SERCOS. For the sensor/actuator connection, digital and analog I/O and corresponding infeed modules are available.

I/O module COMSOFT
PROFIBUS DP Master/Slave, cRIO

PROFIBUS DP Master/Slave Module for CompactRIO™
The COMSOFT cRIO PB module connects the CompactRIO chassis directly and for the first time to PROFIBUS DP networks.

The cRIO PB module features cyclic DPV0 Master class 1 services for the fast exchange of I/O data as well as acyclic DPV1 Master class 2 services for configuration and diagnosis purposes. The module additionally supports DP Slave mode for the integration in existing PROFIBUS DP networks, e.g. in combination with a PLC.

The small sized and rugged platform CompactRIO from National Instruments is a control and acquisition system designed for applications that require high performance and reliability. Using FPGA technology (Field Programmable Gate Arrays) the implementation of hard real-time-enabled systems is also possible. cRIO is a modular system and there is a wide range of industrial I/O modules available. This results in combination with the cRIO PB module in an extremely attractive solution for the realisation of PAC systems implementing high-complex data acquisition and control functions at the same time.

A direct LabVIEW™ VI interface for a seamless integration of the module and a full graphical Windows based PROFIBUS DP configuration tool are available.

The easy-to-use VI interface provides detailed examples incl. source code for DP Master and DP Slave.

I/O module GEFRAN

High-performance distributed I/O system

Gateway for GDNET network
Gateway for main field Busses
Entirely configurable via software
Completely remote from the field
Modular
Simple for cabling
Sturdy

I/O module Horner APG

Our modular SmartStack I/O expansion system allows the flexibility of using digital, analog and specialty I/O boards. You can choose from various I/O combinations and stack up to four different I/O boards onto a single OCS station, as well as our TIU200. This modular, quick stacking approach provides scalability and flexible design.

-Wide variety of I/O and Speciality Modules
-Massive Analogue range
-Compact and Stackable
-Communications Modules available

~ Cscape™: All Units are programmable with a Free Software ~

I/O module LENZE

The increasing level of automation in machines and systems and the consequent rise in the number of I/O devices have in turn increased the amount of wiring required. Decentralised I/O systems bring order to this chaos. Lenze offers two product concepts with IP 20 degree of protection which are suited to both simpler digital applications and more complex automation tasks.

Compact system
The compact version is available in 8, 16 and 32-channel modules with up to 24 inputs and 8 outputs, using single or three-wire technology.
more >>

Modular system
The modular version consists of three components: a gateway, electronic modules and a backplane bus. Up to 32 elements can be combined as desired.

I/O module Georg Schlegel GmbH Co KG
Profibus, EIB, Interbus-S, CAN

Option to network the Schlegel control units and pilot lights (control devices, operator consoles, panels...) to the most common Fieldbus systems (such as AS-Interface, CANopen, Profibus DP, ...).
The Fieldbus compatible Schlegel control units are particularly for applications using a large number of control units and pilot lights to be connected to the Fieldbus at less wiring effort.

I/O module WAGO
PROFIsafe

The WAGO-I/O-SYSTEM 753 PROFIsafe modules are binary inputs and outputs as per IEC 61508 for the application on the PROFIBUS with PROFIsafe and can be utilized without major modifications to the existing system of Series 753.

I/O module WAGO

WAGO-I/O-SYSTEM 750 - One system for all applications
The "optimum" fieldbus system.
With a fieldbus-independent design that features finely modular components, with its decentral fieldbus system, the WAGO-I/O-SYSTEM is approved for extremely diverse applications.

The system is optimized for process-oriented communication and is a scalable-performance solution for high integration density with an unbeatable price / performance ratio.

The diversity of possible applications are almost infinite.
The hardware and system costs have been reduced to a minimum in doing so.
For simple use that ensures maximum efficiency.

I/O module Woodhead

The BradControl family of I/O modules provides a reliable solution for connecting industrial controllers communicating on industrial networks to I/O devices. Both in-cabinet and on-machine harsh environment applications are supported.

In-Cabinet:
The BradControl Block I/O system is an effective way to connect industrial I/O devices to a PLC or PC controller over PROFIBUS. The BradControl interface solution is comprised of a network adapter and up to 32 expansion modules mounted in an enclosure close to the field devices.

On-Machine:
BradControl I/O modules provide a reliable solution for connecting industrial controllers communicating on PROFIBUS to I/O devices in harsh environments. Rated for IP67 environments, BradControl I/O modules can be machine mounted and are able to withstand areas where liquids, dust or vibration may be present.

I/O module Woodhead
Ethernet

The BradControl family of I/O modules provides a reliable solution for connecting industrial controllers communicating on industrial networks to I/O devices. Both in-cabinet and on-machine harsh environment applications are supported.

In-Cabinet:
The BradControl Block I/O system is an effective way to connect industrial I/O devices to a PLC or PC controller over Ethernet. The BradControl interface solution is comprised of a network adapter and up to 32 expansion modules mounted in an enclosure close to the field devices.

On-Machine:
BradControl I/O modules provide a reliable solution for connecting industrial controllers communicating on Ethernet to I/O devices in harsh environments. Rated for IP67 environments, BradControl I/O modules can be machine mounted and are able to withstand areas where liquids, dust or vibration may be present.

I/O module ifm electronic
AS-Interface

I/O modules for field applications
The ifm field modules are available in different versions for different applications. The ProcessLine for food and process automation with the protection rating IP69K, the CompactLine for robust applications and the ClassicLine for standard applications, both in IP67. Illuminated pushbutton modules complement the product range.

I/O module moxa
SMS, SNMP, TCP

Introduction
The ioLogik E4200 is suitable for remote monitoring and alarm systems, such as are used for water treatment systems, water supply systems, wastewater treatment systems, and power monitoring systems. These kinds of applications need more I/O points and a variety of I/O types, including temperature sensors, gas detectors, and water quality detectors, all of which can benefit from the versatile mixture of I/O features supported by the ioLogik E4200.

Features
• Supports up to 16 I/O modules
• Dual Ethernet LANs and one RS-232 port
• Front-end intelligence that supports 80 Click&Go rules
•Unicode Active Messaging with real-time stamp, including SMS, SNMP Trap with I/O status, TCP, email
• Built-in web console
• PC utility: Auto detection of installed modules
• Windows/WinCE VB/VC.NET and Linux C APIs

I/O module GE Fanuc Intelligent Platforms

I/O Modules

Customize your FPGA Computing design with I/O modules which provide flexibility in the face plate connectors and transmission protocols available for use with the TS Series processing board

I/O module Measurement Computing

Analog I/O
14 and 16 bit resolution
CB COM Evaluation Kits
Temperature

Analog Output
12-bit or less resolution
14 and 16 bit resolution

Digital I/O
Counter-Timer
High Voltage
Parallel

Serial Communications
CB-COM Communication Interfaces

I/O module OSAI

RIO – (Remote Input Output) is a compact modular system of remote I/O modules available from OSAI for the management and control, through a field bus, of inputs and outputs distributed throughout the plant.
The modular structure of each RIO block guarantees a high degree of flexibility to reduce installation and maintenance costs. In the event of a malfunction, the electronic section of any block can easily be replaced without having to disconnect cables. The status of each input and output on every block is displayed with a LED indicator. External cables are easily connented by inserting wires into simple contact blocks thus avoiding the inconvenience and uncertainty associated with traditional screw terminals.
All units use a simple “snap on” connection to the DIN support rail connected to the bus coupler so that a series of RIO blocks (digital, analogue and intelligent), can be installed in a variety of combinations.
RIO bus coupler : is an interface unit that connects the RIO blocks to the bus. It manages up to 8 modules.
RIO I/O MODULES.

Digital versions:
- RIO 16 I /Kes - 16 Input module
- RIO 16 O /KEs - 16 Output module
- RIO 8 I/O - 8 I/O configurable module
- RIO 8I 8I/O /KEs - 8 Input + 8 I/O configurable module.

Analogical versions:
- RIO 4AI ±10V - 4 analogue input module (+-10Vdc)
- RIO 4AI 20mA - 4 analogue input module (0-20mA)
- RIO 4AI/4AO ±10V - 4 input + 4 analogue output module (+-10Vdc)
- RIO 4AI/4AO 20mA - 4 input + 4 analogue output module (0-20mA)

I/O module Omniflex

IEC 61131 Workbenches Control Strategy Programming

The WorkBenches are price structured according to I/O capability, with a range from 32I/O to unlimited. This allows the user to pay according to the scale of the system. The workbench is a once off cost and can be used with many CPUs. The workbenches are Windows operating systems based.

I/O module ROSS Controls

I/O Modules
The Serial Bus System is a completely integrated solution with an extremely fast I/O backplane that uses change-of-state (COS) connections to maximize performance

Power Type: Electro-Pneumatic

Modularity features allow easy module replacement with unique latching mechanisms and auto device replacement which allows OEMs to add I/O modules without making changes to the control software. A full set of I/O modules accept signals from sensors, photo eyes, limits and other field input devices as well as providing signals to remote solenoid valves and other output devices. There is a choice of digital, analog, and high-watt I/O modules, which include built-in short circuit and open circuit detection circuitry with electronic feedback. A single ROSS serial bus communication module supports up to a maximum of 63 I/O modules and up to 264 inputs and 264 outputs.

- Accepts signals from sensors, photo eyes, limits and other field input devices.
- Provides signals to remotely operating solenoid valves and other field operating output devices.
- Choice of digital, analog, high watt I/O Modules.
- Choice of connectors: 8mm, 12mm or M23.

I/O module Soft Servo Systems Inc

The IM-300 is a 64-point general I/O module with built-in wire-entry screw terminals and LEDs that extends the I/O capabilities of a Soft Servo system. It requires a VersioBus adapter board to connect to a VersioBus I/O network. Up to four IM-300s can be daisy-chained together for distributed control and multiple nodes with VersioBus fiber optics, to provide as many as 256 additional I/O points.

I/O module Stonel
Modbus

Foundation Fieldbus H1 level has been designed as a digital replacement of the 4 to 20mA standard in the process industries. Foundation Fieldbus is also a LAN (Local Area Network) for instruments used in both process and manufacturing automation with built-in capability to distribute the control application across the network. The physical wiring is also fully compatible with intrinsic safety (IS) or nonincendive wiring standards and may be used in hazardous, as well as general purpose areas. In hazardous areas standard explosion-proofing or power limited concepts may be used, as well as IS concepts, offering greater cabling design flexibility.

I/O module Stonel
AS-Interface

AS-Interface networks up to 62 field devices onto a single pair of wires that delivers both signal and power. Actuator Sensor Interface, or AS-Interface, was developed by a group of sensor manufacturers and introduced into the market in 1994. Since that time, it has become the de facto standard for discrete sensors in process industries throughout the world. AS-Interface may be used in hazardous process environments using explosion proof, tray cable, nonincendive and for nonincendive wiring protection concepts.

I/O module Stonel
DeviceNet

The DeviceNet protocol dramatically reduces costs by integrating up to 62 devices on a 4-wire trunk network. Communications data is carried over two wires with a second pair of wires carrying power. Discrete and analog devices may be connected into the DeviceNet protocol.

I/O module Bosch Rexroth Electric Drives and Controls

Rexroth Inline is the flexible, scalable and modular I/O system for time-saving control cabinet installation – be it locally on the IndraControl L itself or as a distributed I/O station.

Rexroth Inline is available in two different versions for all standard fieldbus systems:
• Inline Modular – with fine scalability for individual configuring
• Inline Block – a bus coupler with integrated I/Os as the ideal solution for nodes with a limited number of I/Os

Advantages

* simple – use and application
* integrated – as fieldbus or local I/O
* open-architecture – support for all common bus systems
* flexible – best modularity
* reliable – wide bandwidth and low temperature sensitivity
* time-saving – installation without tools and precise diagnostics
* space-saving – high-density modules

I/O module LENZE

I/O module NATIONAL INSTRUMENTS

- Customized control algorithms
- Reliable embedded operation for process equipment
- Built-in signal conditioning
- Remote Web browser and FTP interface
- Rugged, intelligent, distributed I/O for process automation
- Real-time performance for control applications

Learn about NI Compact FieldPoint! National Instruments FieldPoint is designed for measurement, industrial control, and data logging applications that require reliable, rugged systems involving diverse sensors and actuators located centrally or spread over large distances. NI FieldPoint includes networking capabilities for distributed I/O as well as an option to run a real-time operating system, which runs LabVIEW Real-Time applications. FieldPoint and Compact FieldPoint are easy-to-use data acquisition and control hardware composed of industrially rugged, dependable I/O modules and communication interfaces. With the FieldPoint family of distributed I/O, you can perform your process automation functions reliably even in electrically and environmentally harsh environments.

I/O module PMA

- RM 221-x: standard signals 0/4...20mA, -10/0...10V
- RM 222-x: standard signals 0/4...20mA, -10/0...10V + TPS with supply for transducers and potentiometric transmitters

Applications
Decentralized input/output modules RM 200
Modular system

Main attributes
4 channel per module
resolution: 12 Bit
configurable functions
standard signals: I = 0/4...20mA, U = -10/0...10V
variants: 4x I, 4x U, 2x I & 2x U
RM 222-x with internal transducer supply 24V/5V
LED indicators: 4x status
screw-/plug-in terminals
plug-in module

I/O module SIEMENS

Centralized PC IO peripherals

For especially high-speed and real-time-enabled measuring, open-loop and closed-loop control tasks, the SIMATIC Microbox PC can be expanded modularly and flexibly with centralized IO peripherals.

The encoders/counters and digital and analog IO modules are integrated extremely compactly via PCI-104 expansion slots using an expansion rack.

In the maximum configuration this allows the integration of up to 120 analog IO, 320 digital IO, and 12 encoder/counter interfaces.