|
|
Bistable solenoids have two stable end positions which are maintained without current. Between the two end positions switching is effected with a current impulse of varying polarity.
90 % of our solenoids are made to customer’s specifications. Please do not hesitate to contact us concerning any solenoid specific questions.
|
|
Made according to the following norms: DIN VDE0580, NFC79300 y UNE-EN 60204-1..
Bistable solenoid is a simple effect product, the stroke from the initial position (s) to the end is made by a direct or retified electrical polarized signal. To return to the initial position it is necessary to send an electrical signal of inverse polarity (direct or alternating) equal to the nominal voltage, this signal will only vary the force of the magnet, it will not produce any returning or repulsion force. To make the plunger return to its initial position it is necessary to use external forces such as a spring.
CE-This product is made according to the 73/23/CEE Low Voltage European Guideline about electrical appliance for certain limits of voltage and modification 93/68/CEE. The fulfilment of the 89/336 CEE (electromagnetic compatibility) norms must be assured by the user.
|
|
Deltrol Controls specializes in providing custom solenoid designs for customer applications. We can provide solenoid only solutions, or value added assemblies. We also offer a wide range of standard linear solenoids in C-Frame, D-Frame, and tubular constructions.
Contact one of our sales engineers to discuss your specific application
Phone: (01) 414 671 6800
Fax: (01) 414 671 6809
Email: sales@deltrol.com
Website: www.deltrol-controls.com
|
|
An electromagnetic suction cup makes it possible to maintain a device (interdependent of a polar plate) in a given position and to release it by simple electrical signal. In the case of a suction cup with emission of current, the maintenance is ensured not under tension by a permanent magnet and the unlocking of the polar plate is caused by the powering of the reel which involves the demagnetization of the magnet.
Applications Fire protection Maintenance and release of fire doors, opening emergency exits of trap doors of smoke clearing, valves of ventilation… Industrial use Locking or unlocking, access control, maintenance or gripping of pièces… ...
|
|
DESCRIPTION:
The attraction and the lifting of the magnetic pieces is obtained by energising the coil inside the electromagnet.
When the energising stops the piece is removed.
When operating with loads the corresponding security rules must be respected by the user.
Options: Clamping screw for VEM25 and higher connector for VEM-65 and higher.
- NAFSA, reserves any possibility of modification.
|
|
CI SERIES
Double-coil linear solenoids, which, besidesa high pulling force, offer a holding function with a continuous duty cycle of 100% ED.
They can be customized with different accessoires and are suited for both traction and thrust applications.
|
|
|
Dexter Magnetic Technologies designs and manufacturers electromagnets using innovative and patented designs.
|
|
An electromagnetic suction cup makes it possible to maintain a device (interdependent of a polar plate) in a given position and to release it by simple electrical signal. In the case of a suction cup with emission of current, the maintenance is ensured not under tension by a permanent magnet and the unlocking of the polar plate is caused by the powering of the reel which involves the demagnetization of the magnet.
Applications Fire protection Maintenance and release of fire doors, opening emergency exits of trap doors of smoke clearing, valves of ventilation… Industrial use Locking or unlocking, access control, maintenance or gripping of pièces… ...
|
|
|
|
|
|
For over 40 years, The Ogallala Electronics Division of Arnold has manufactured electromagnets (shaped field magnets) made of thin-gauge copper or aluminum foils as well as the more economical wire wound type. The shaped field magnet, sometimes referred to as a solenoid, approaches the ideal for flexibility in generating magnetic fields so desirable for klystron, TWT, ion implantation, chemical etching, chemical dispersion, MRI and other wave guide applications.
Ogallala Electronics manufactures a wide variety of custom design electromagnets which generate uniform or proportioned magnetic field shapes and with a wide range of magnetic field intensities. These electromagnets are either made up of tape wound foil wafers or built up from coils of wire. In the tape wound electromagnets, each wafer is electrically controlled to the precise field strength desired. The resultant field distribution may be uniform or it may have peaks, plateaus and valleys along the axial length of the electromagnet as dictated by the customer requirement. When a specific field shape is desired, the shaped field electromagnet can be designed to that configuration with great precision. Wafers may be of various widths within the electromagnet and they can be made interchangeable. Nominal I.D. and O.D. may be selected to meet application size requirements.
Special designs are available which utilize chilled oil or liquid nitrogen to allow higher than normal current, generating up to 200% greater field intensity than an uncooled design.
|
|
|
|
|
|
ENCAPSULATED COILS
These coils have a natural application in the field of solenoid valves for the most varied sectors.
The range is composed of numerous types, with different dimensions, powers, materials and electrical connections. The standard versions and the availability of developing new ones, allow optimum solutions for even the most complicated demands.
LINEAR SOLENOIDS
These solenoids are used in the most varied industrial applications where there are demands for linear actuations.
They are available with galvanised steel body or with encapsulated coils, allow an high number of hourly operations and guarantee an extremely long life cycle.
HOLDING SOLENOIDS
The holding solenoids, designed to operate in DC, are characterised by a rugged body in galvanised steel.
The range allows for external diameters from 19mm to 70mm. Holding force goes up to 1.300N. This feature is even more relevant considering the possibility of continually operating at ED100%.
LOCKING SOLENOIDS
DELTA production is aimed at constructive choices for both simplicity and robustness, guaranteeing maximum reliability and efficiency. They are available in three different sizes, all have a built-in return spring and are produced with encapsulated coils or with stainless steel body.
|
|
|
|
|
|
DICTATOR provides complete hold open systems for hazardous areas
They comprise explosion-proof smoke and heat detectors, door operators and the electromagnets. They comply with the requirements for group II products and can be installed in all zone 1 and 2 areas (according to VDE 0165). The explosion proof magnets are encapsulated (EEX m). Two series are available: with ex-proof connection box or with connection cable. The standard length of the cable is 2 m, but it can be delivered in the length required on site. The holding force of the magnets is either 550 N or 145N. The integrated release pin eliminates any remanence after switching off the power supply of the magnets, ensuring that the magnets always releases the door. All ex-proof magnets are equipped with diodes and polarity protection.
The DICTATOR ex-proof magnets have been tested both according to EN 1155:2005 for hold-open systems and the ATEX directive by the Physikalisch-Technische Bundesanstalt Braunschweig (certificates PTB 03 ATEX 2174 X and PTB 03 ATEX N060).
In addition to the ex-proof magnets DICTATOR also provides a large range of electromagnets for hold-open systems, that comply with the EN 1155:2005 and are approved for the use in hold-open systems.
|
|
Doorholder magnets, explosion proof
Doorholder magnets with 650 N, 1300 N and 2000 N force, explosionproof, in acc. with ATEX 94/9/EC, II2G EEx m II T6, II2D IP66 T85, for use in hazardous areas zone 1, 2, 21 and 22 for all kind of gas, mixtures, vapours and dust (in acc. to type). Protection class IP65.
|
|
Heavy duty solenoids feature a fully encapsulated design. Thanks to the high material fraction the solenoid system contains a lot of iron allowing optimum use of the available space in relation to the required output. We supply these solenoids in cylindrical or square design.
90 % of our solenoids are made to customer’s specifications. Please do not hesitate to contact us concerning any solenoid specific questions.
|
|
These industrial holding magnets are units with an electromagnetic
holding system without an armature that is an open magnetic
circle for the holding of ferro magnetic parts.
The greatest holding force is dependant on the surface roughness
and component thickness.
Devices with permanent magnets and rectangular holding magnets are also available.
Size: 15 - 250 mm diameter
Max. holding force: 36 - 30000 N
(please note catalogue indications)
Rated torque: 1.4 - 90 W
|
|
Electromagnetic holding solenoids are solenoid systems without armature. In the energized state any ferromagnetic material is held. We also supply series PHD permanent holding solenoids which generate a holding force in a non-energized state.
90 % of our solenoids are made to customer’s specifications. Please do not hesitate to contact us concerning any solenoid specific questions.
|
|
An electromagnetic suction cup makes it possible to maintain a device (interdependent of a polar plate) in a given position and to release it by simple electrical signal. In the case of a suction cup with emission of current, the maintenance is ensured not under tension by a permanent magnet and the unlocking of the polar plate is caused by the powering of the reel which involves the demagnetization of the magnet.
Applications Fire protection Maintenance and release of fire doors, opening emergency exits of trap doors of smoke clearing, valves of ventilation… Industrial use Locking or unlocking, access control, maintenance or gripping of pièces… ...
|
|
The electromagnetic suction cups are electrically ordered magnets.
They make it possible to easily maintain a system in a determined position, and to slacken it at the desired time.
Forces of 45 with 680N, for diameters ranging between 25 and 45mm
|
|
Operating mode:
Locked in rotation through fork shaped
mechanical link
Released either by power-off or
power-on mode
Manuel reset
Typical application:
Fire protection: door retainers,
smoke damper
Benefit:
High torque level with low power
consumption
|
|
DESCRIPTION:
The attraction and the lifting of the magnetic pieces is obtained by the magnet mounted in.
By energising the coil inside the electromagnet the piece is removed.
When operating with loads the corresponding security rules must be respected by the user.
Remanence during the neutralize of the magnets is aproximately 2 % of the retention force at 0,015 air gap.
When handling loads a security factor of 3 is necessary, the weight of the piece must be half of the magnetic force of the electromagnet.
- Options: Clamping screw for VEM25 and higher connector for VEM-65 and higher.
- NAFSA, reserves any possibility of modification.
|
|
DICTATOR manufactures electromagnets tested and approved according to the EN 1155:2005.
An extensive product range of electromagnets and counter plates
covering most applications.
Holding forces up to 5000N
Voltage: Standard 24 VDC, other tensions also possible
Special designs
- Ex-proof magnets
- IP65
- Magnets with UV-resistant sealing resin for outside applications
- Magnets to be integrated in overhead door closers
- Customized designs
|
|
These electromagnetic holding magnets are used in electrically operated independent clamping devices to hold open fire protection doors and exits. The doors are held open either in a fixed position or in a manually adjustable angle until they are electrically released.
Magnets for EX applications with ATEX certification are available.
Size: 42 - 70 mm with quality control
Holding force: 300 - 1568 N by quality controlled
goods
Rated torque: 1.5 - 3.0
|
|
DESCRIPTION AND OPERATION
Assembled on a fixed part, these suction cups ensure the magnetic maintenance of the doors via a reinforcing plate. The release is obtained: by electric drive remotely cut of the supply voltage for the models with lack of tension powering for the models with emission of current manually via a pushbutton (models with lack of tension). The return to the position “maintenance” is obtained while bringing back the door in the initial position.
|
|
Material generally linked to a fire system which will automatically release the fire doors in case of a fire, by switching the power off.
Electromagnetic holder mounted in a metallic box painted with white epoxy, with cabled local release button, protection level IP42, delivered with an equipped magnetic pin
|
|
Floor Mounted
The unique design provides maximum protection for areas subject to vandalism or accidental damage.
- 200N or 500N holding force
- Zero residual force
- Robust aluminium construction
- Surface cable entry
- Supplied with Keeper Plate
|
|
Combination of an electromagnet (displacement) and an electromagnetic suction cup (locking)
These products are developed and manufactured by LUXALP to meet your specific needs
|
|
Part number 8.P29.45 8.02.51.19 8.04.AM.52 8.10.BM.28
Locking mode Power off Power off Power off Power off
Nominal stroke 3 mm 8 mm 5 mm 11 mm
Shearing strength (daN) 5 5 10 60
Return force (daN) 0,015 0,05 0,03 0,1
Absorbed
2 17 5,5 9
power (W)
Duty cycle 100 % 15 % 100 % 100 %
Total cycle time 2 mn
Standard voltage 24 Vdc 24 Vdc 24 Vdc 24 Vdc
|
|
Deltrol Controls offers a wide range of standard linear solenoids. We have C-Frame, D-Frame, and tubular constructions. In addition to our standard product line, we have the ability to offer custom solutions that range from simple modifications of a standard product to an entirely new solenoid designed for your application.
Many of our products utilize class F (155 C) thermoplastic encapsulated coils. This provides for excellent thermal properties and protection for the coil windings.
Our solenoids are thoroughly tested to insure you receive a high quality product. Additionally, many of our solenoids carry UL certification either as a component or for the insulation system used.
Contact one of our sales engineers to discuss your specific application
Phone: (01) 414 671 6800
Fax: (01) 414 671 6809
Email: brian-cahill@deltrol.com
Website: www.deltrol-controls.com
|
|
|
|
Electro-magnets
